When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

A magnet or retaining ring holds the nut in place.

Because they make contact on the flat sides of fasteners rather than only on the corners, these magnetic bits significantly reduce slipping and stripping. They’re also known as lobular bits.

Assortments contain bits with multiple drive styles.

These bits are also known as nut setters.

The assorted drivers in these sets have a ball end that allows angled entry to turn screws in hard-to-reach areas.

A holding mechanism at the tip of the tool ensures the screw won’t slip off.

When working in tight spaces, these short drivers fit where others can't.

A scaled-down version of standard nutdrivers, these tools are shorter, slimmer, and easy to take with you.

Sets include an assortment of drivers that are drilled all the way through the shaft and handle for turning nuts on any length of threaded rod. They have a magnet in the tip to hold nuts in place.

Press down on the handle’s collar to adjust the shaft length or remove and replace the shaft to change sizes. Sets include a handle and multiple shafts.

The assorted drivers in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. They are tested to 1,000 volts to meet ASTM and IEC standards.

Made of aluminum-bronze that is FM approved, these drivers help meet OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

When working in tight spaces, these short drivers fit where others can't. Bits have a different tip at each end and snap into the shaft, which is also a nutdriver.

Sets include an assortment of keys. These simple tools turn fasteners from either end and reach into tight spots.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. Use to turn screws in hard-to-reach spots.

The extra-short leg of these keys fits in tight spaces other tools can't and the long-leg ball end allows angled entry to turn screws in hard-to-reach areas.

All of the keys in these sets have an extra-short leg to fit into tight spots and a ball end to turn screws at an angle in hard-to-reach places. Their bright chrome-plated finish makes them easy to see, reducing the chance you’ll lose them.

These keys have an extra-short leg to fit into tight spaces that other tools can’t, and a ball on the long leg for angled entry to turn screws in hard-to-reach places. A bright chrome-plated finish makes them easy to see and less likely to be misplaced.

These assorted keys have a bright finish that's easy to see, so they’re less likely to be misplaced. They turn fasteners from either end and reach into tight spots.

Sets include assorted keys with each size a different color for easy identification. When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.

These assorted keys have a detent that grips inside the recess to ensure screws won’t fall off. The ball end allows angled entry to drive fasteners in hard-to-reach areas.

The zinc coating on these keys resists salt-spray exposure. They turn fasteners from either end and reach into tight spots.

The ball end allows angled entry to turn screws in hard-to-reach areas. Protect your stainless steel screws by using a stainless steel L-key. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Sets include an assortment of stainless steel keys, which protect stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

These assorted keys are made of beryllium copper that is FM approved. They help meet OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. Keys turn fasteners from either end and reach into tight spots.

Sets include assorted keys with long shafts that reach into tight spots. The plastic-covered handles provide a good grip for your whole hand.

Sets include an assortment of short keys that fit in tight spaces where others can't.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. The textured grip provides comfort, slip resistance, and maximum torque.

These assorted keys have a textured grip that provides comfort, slip resistance, and maximum torque. They have a long shaft for reaching into tight spots to turn fasteners.

The economical choice, these sets include an assortment of keys with a simple loop handle. The long shaft reaches into tight spots and the T-handle provides a good grip for your whole hand when turning fasteners.

These sets include an assortment of keys with a ball end on the long shaft, which allows angled entry to turn screws in hard-to-reach areas. The short shaft provides additional torque.

The ball-end tip has a retaining ring that grips inside the recess to hold screws in place and allows angled entry to turn fasteners in hard-to-reach areas.

Protect your stainless steel screws by using a stainless steel key. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Sets include an assortment of keys with a long shaft for more reach and a short shaft for more torque. Use stainless steel keys to protect your stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

The assorted keys in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900 and ASTM F1505-01. They have a long shaft that reaches into tight spots to turn fasteners.

These assorted shafts attach to a handle or can be used with socket wrenches and power tools. They have a ball end that allows angled entry to make good contact with the recess when a standard-tip shaft can’t.

Keep a set of keys neatly in your tool box or pocket to turn multiple fastener sizes.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet ASTM F1505 and IEC 60900.

The short bit on these sockets fits in spaces where height clearance is limited.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

These short sockets fit spaces where height clearance is limited.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet IEC 60900.

Turn many sizes of square, hex, and 8-point fasteners with one socket. Place over the fastener and 54 pins move to grip it securely.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the socket.

Achieve the best possible grip on hex fasteners and prevent rounding.

With a smaller OD than standard sockets, these fit between tightly spaced fasteners.

A magnet holds the fastener securely enough to drive self-tapping screws.

Extra-long bits allow access to hard-to-reach fasteners.

Extra-long bits allow access to hard-to-reach fasteners.

Keep a convenient mix of hex, Torx, Phillips, and slotted bit sockets on hand.

Suitable for occasional maintenance work, these sets are imported.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the socket.

The hex shape grips hex fasteners and prevents rounding. These sockets are made to withstand the high torque and force of impact tools.

One head is angled 60° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

These wrenches are made of stainless steel for excellent corrosion resistance.

One head is angled for access to hard-to-reach fasteners. These are also known as ignition wrenches.

When turning fasteners in small spaces, these short wrenches fit where others can't.

Made of stainless steel, these wrenches have excellent corrosion resistance.

When turning fasteners in small spaces, these short wrenches fit where others can't.

When working in tight spaces, these short wrenches fit where others can't.

A lever reverses the ratchet direction.

Flip these wrenches over to ratchet in the opposite direction.

Flip these wrenches over to ratchet in the opposite direction.

Pivot the box end for access to fasteners in tight spots.

Suitable for occasional maintenance work, these sets are imported.

When working in tight spaces, these short wrenches fit where others can't.

The offset head gives you additional clearance to turn hard-to-reach fasteners.

Ratchet mechanisms allow you to turn fasteners in tight spaces without removing and repositioning the tool.

A ratchet mechanism allows you to turn fasteners in tight spaces without removing and repositioning the wrench.

The heads are offset to provide clearance for reaching over obstructions.