The toughest bits available, these withstand the shock and twisting force of impact drivers.

When you don't have exact alignment between the fastener and the bit, the ball end allows angled entry to turn screws in hard-to-reach areas. A retaining ring grips inside the recess to hold screws in place.

An opening at the tip accommodates the pin in the recess of tamper-resistant hex screws. These are also known as pin-in-hex or pin-in-socket bits.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

Assortments contain bits with multiple drive styles.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

The assorted drivers in these sets have a ball end that allows angled entry to turn screws in hard-to-reach areas.

Sets include an assortment of drivers with soft, contoured handles that provide comfort and the best possible grip for achieving maximum torque.

The assorted drivers in these sets have a holding mechanism at the tip that ensures the screw won’t slip off.

Sets include an assortment of nutdrivers.

Made of aluminum-bronze that is FM approved, these drivers help meet OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Press down on the handle’s collar to either adjust the shaft length or remove the shaft and replace it for a different tip. Sets include a handle and multiple reversible shafts.

Sets include an assortment of drivers that allow you to apply constant pressure to small hex nuts and cap screws. Press the rotating end cap on the handle with your palm while turning the body of the driver with your fingertips.

The handle on these assorted ESD-safe nutdrivers drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Press the rotating end cap to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Sets include assorted keys with long shafts that reach into tight spots. The plastic-covered handles provide a good grip for your whole hand.

Sets include an assortment of short keys that fit in tight spaces where others can't.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t.

These assorted keys have a textured grip that provides comfort, slip resistance, and maximum torque. They have a long shaft for reaching into tight spots to turn fasteners.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. The textured grip provides comfort, slip resistance, and maximum torque.

The economical choice, these sets include an assortment of keys with a simple loop handle. The long shaft reaches into tight spots and the T-handle provides a good grip for your whole hand when turning fasteners.

These assorted keys have an extra-long shaft that provides access to fasteners in deep recesses. To change tips, use a hex key to loosen the set screw.

The long shaft has a ball end for angled entry to turn screws in hard-to-reach areas. The short shaft provides additional torque.

The ball-end tip has a retaining ring that grips inside the recess to hold screws in place and allows angled entry to turn fasteners in hard-to-reach areas.

Protect your stainless steel screws by using a stainless steel key. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Sets include an assortment of keys with a long shaft for more reach and a short shaft for more torque. Use stainless steel keys to protect your stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC and ASTM standards. They have a long shaft that reaches into tight spots to turn fasteners.

Sets include an assortment of keys. These simple tools turn fasteners from either end and reach into tight spots.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. Use to turn screws in hard-to-reach spots.

A bright finish makes these tools stand out, so they're less likely to be misplaced. They turn fasteners from either end and reach into tight spots.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places. These keys have a bright gold-plated finish that makes them easy to see and less likely to be misplaced.

The ball end has a detent to grip inside the screw recess and allows angled entry to turn fasteners in hard-to-reach areas.

Each size of these keys is a different color for easy identification. When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places. These keys have a zinc coating that resists salt-spray exposure.

A flexible joint provides access to fasteners in hard-to-reach areas.

Protect your stainless steel screws by using a stainless steel L-key. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

These assorted keys are made of beryllium copper that is FM approved. They help meet OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. Keys turn fasteners from either end and reach into tight spots.

Made of beryllium copper that is FM approved, these keys help meet OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. They turn fasteners from either end and reach into tight spots.

These assorted shafts attach to a handle or can be used with socket wrenches and power tools. They have a ball end that allows angled entry to make good contact with the recess when a standard-tip shaft can’t.

Select any key without unfolding the others in the set. The assorted keys turn multiple fastener sizes.

Bright-colored handles make these tools stand out, so they’re less likely to be misplaced. Sets include an assortment of keys for turning multiple fastener sizes.

When working at heights, secure a lanyard to the ring on these tools and prevent drops. Sets include an assortment of keys for turning multiple fastener sizes.

Extra-long bits allow access to hard-to-reach fasteners.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

These sockets are also known as pin-in-hex or pin-in-socket bits.

Use bit sockets as an alternative to a screwdriver or L-key.

The short bit on these sockets fits in spaces where height clearance is limited.

Extra-long bits allow access to hard-to-reach fasteners.

Keep a convenient mix of hex, Torx, Phillips, and slotted bit sockets on hand.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

For high quality at a lower price, choose these U.S.A.-made sets.