Strong and durable, these multipurpose bits are for use with bit screwdrivers.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

A retaining ring at the tip grips inside the recess to ensure screws won't slip off the bit.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

Ribs forged into the wings of these bits grip the screw recess to reduce stripping. They're also known as ACR® bits.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

Remove screws in hard-to-reach places. A spring-loaded sleeve guides bits onto the screw head and keeps them from slipping out.

A wide tip makes good contact in shallow and coated screw recesses, such as those filled with paint.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

The slightly tapered tip wedges into the screw recess for a secure hold. Also known as Torx-Align bits.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

The small-diameter shaft can access screws in narrow recessed holes.

Bits have a different size at each end.

The toughest bits available, these withstand the shock and twisting force of impact drivers. Designed for screws with a square recess in the head, they are also known as Robertson bits.

Bits have a different size at each end.

An opening at the tip accommodates the pin in the recess of tamper-resistant Torx screws. These are also known as pin-in-Torx bits.

An opening at the tip accommodates the pin in the recess of tamper-resistant hex screws. These are also known as pin-in-hex or pin-in-socket bits.

Turn two drive styles with one reversible bit. Remove and replace to change the tip.

Ribs forged into the wings of these offset-cross-shaped bits grip the screw recess to reduce stripping. They are also known as ACR® bits.

The six rounded points fit the star-shaped recess of Torx-Plus screws. These bits have a similar profile to Torx but are not recommended for use with standard Torx screws.

Also known as Reed and Prince bits.

Strong and durable, these multipurpose bits are for use with bit screwdrivers.

These are also known as known as butterfly and Type G bits.

A three-winged tip fits triangular slotted screw recesses.

While screws with a square/Phillips combination drive can be turned with either a square or Phillips bit, these make the best contact so you can apply high torque without slipping and stripping the recess. They are also known as Quadrex bits.

A magnet or retaining ring holds the nut in place.

Turn hex nuts and cap screws.

Use hex-shank bits (also known as insert bits) in powered tools.

Bend these adapters up to 90° to access hard-to-reach fasteners. Use them to hold hex-shank bits (also known as insert bits) in powered tools.

Keep bits from slipping. Insert a bit into the adapter, place a screw on the end of the bit, and slide the adapter sleeve over the screw. The sleeve retracts as the screw is driven. These adapters hold hex-shank bits (also known as insert bits) in powered tools.

Lock your bit into the adapter to prevent accidental disengagement. These adapters attach to square-drive tools.

A retaining ring grips inside the recess to hold screws in place. These bits have a ball end that allows angled entry to drive screws in hard-to-reach areas.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

The knurled shank on these bits allows finger tightening. They can also be used with the included screwdriver.

The slightly tapered tip wedges into the screw recess for a secure hold. These are also known as Torx-Align bits.

A magnet holds the nut in place.

A three-winged tip fits triangular slotted screw recesses.

These bits have an offset cross shape.

Grip the indentations on the head of tri-groove fasteners.

An opening at the tip accommodates the pin in the recess of tamper-resistant hex screws. These are also known as pin-in-hex or pin-in-socket bits.

Use sockets with tools that accept hex shanks, such as impact drivers and power drills.