Choose these hinges for their adherence to strict military standards for material and construction.

Made of carbon fiber, these hinges are as strong as aluminum yet lighter in weight. All have leaves that are connected by a strip of flexible Kevlar instead of a pin.

No need for drilling holes or welding, slip these hinges onto panel and door edges for a secure fit.

When the door is closed, the distance between the leaves is larger than the pin diameter, creating an offset to accommodate a gasket or trim.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Turn a set screw to adjust the door 1/8" up or down after it's hung.

Hinge leaves fit into two cutouts (mortises) to mount flush with the door and frame.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Turn a set screw to adjust the door up or down after it's hung.

Turn a set screw to adjust the door 1/8" up or down after it's hung.

These hinges are made of metal.

Hinge leaves fit into two cutouts (mortises) to mount flush with the door and frame.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Also known as bullet hinges, these hinges are the right size for tight spaces and narrow frames.

These hinges with holes are spring loaded—pull the handle to retract the pin and disconnect a door; release the handle and the pin snaps back.

A keeper holds the pin in a retracted position to make reconnecting doors easier than other pull-release quick-disconnect hinges.

To retract the pin and disconnect a door, squeeze the hinge handles together. Release the handles and the pin snaps back.

Springs in these hinges with holes automatically swing doors and gates closed behind you.

After a light push on the door, springs in these hinges swing doors and gates fully open.

Only one cutout (mortise) is needed for these hinges—the offset design allows surface mounting the door leaf and mortise mounting the frame leaf.

Tighten or loosen an adjustment screw to change the hinge resistance.

These hinges allow 360° of motion.

In addition to rotating 360°, these hinges tilt up and down.

A stop keeps these hinges open at a set angle; push past the stop to open them to 180°.

Longer than other entry door hinges, these piano-style hinges run the entire length of doors for strength and durability.

Bearings allow these hinges to open and close doors smoothly. The mounting holes form an industry-standard half-moon shape.

No need for oil or grease, these hinges are maintenance free. The mounting holes form an industry-standard half-moon shape.

A stud projects from the back of each hinge leaf to prevent the door from being forced open. The mounting holes form an industry-standard half-moon shape.

Only one cutout (mortise) is needed to mount these hinges—the offset design allows surface mounting the door leaf and mortise mounting the frame leaf.

The mounting hole pattern does not follow an industry standard, which means you can work around worn mounting holes when replacing template hinges.

Create precise outlines for hinge mortises (cutouts). Position the cutter on a wood door or frame and hit it with a hammer to imprint the outline.

The mounting holes form an industry-standard half-moon shape.

Plastic bushings on these metal hinges prevent metal-to-metal contact that can release particles as hinges open and close.

Designed to wrap around the edge of the partition frame, these hinges provide a stronger hold than other toilet partition door hinges.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

With large pin diameters for added strength, these hinges can hold heavier doors and gates than other strap hinges.

The hinge pin attaches to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

Bearings allow these hinges to open and close doors smoothly.

These hinges have a standard range of motion of 100° to 120°.

With a 170° range of motion, these hinges are for doors that need to open wide.

Easier to install than other concealed cabinet hinges, these do not require a cutout.

Hinge leaves fit into two cutouts (mortises) to mount flush with door and frame edges.

Instead of mounting to the side of a door, mount these hinges to the top and bottom to allow doors to open wide.

Surface-mount these hinges to the side of a cabinet.

Build test fixtures, prototypes, and other small structures with this miniature version of T-slotted framing and fittings.

Turn the padlock eye to fasten these hasps without a padlock.

Designed for use with cut-resistant padlocks, these hasps have a padlock shackle protector on the strike plate for added cut and pry resistance.

Mount these padlockable eyes to the front of a door and door frame.

Choose this hasp if you need several hasps that open with the same key.