Hammer-Driven Hole Punches
Strengthened edges cut holes in soft metal. These punches are also known as arch punches.
For technical drawings and 3-D models, click on a part number.
For Hole Dia. | Lg. | Material | Each | |
For Use On Brass, Copper, Fabric, Leather, Rubber | ||||
---|---|---|---|---|
7/16" | 4 3/4" | Steel | 0000000 | 000000 |
Hammer-Driven Small Hole Punches
Use these punches to make round holes in soft, nonmetallic materials.
For technical drawings and 3-D models, click on a part number.
For Hole Dia. | Lg. | Material | Each | |
For Use On Fabric, Leather, Rubber | ||||
---|---|---|---|---|
7/16" | 4 1/2" | Steel | 0000000 | 000000 |
One-Step Hammer-Driven Gasket and Washer Punch Sets
Attach two punch heads to the handle at the same time to punch a gasket or washer in a single strike.
Includes | For Hole Dia. | Material | Container Type | Each | |
For Use On Aluminum, Cork, Fabric, Leather, Plastic, Rubber | |||||
---|---|---|---|---|---|
10 Punches, Handle | 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4" | Steel | Plastic Case | 00000000 | 0000000 |
15 Punches, Handle | 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", 7/8", 1", 1 1/16", 1 1/8", 1 3/16" | Steel | Plastic Case | 00000000 | 000000 |
25 Punches, Handle | 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", 7/8", 1", 1 1/16", 1 1/8", 1 3/16", 1 1/4", 1 5/16", 1 3/8", 1 7/16", 1 1/2", 1 5/8", 1 11/16", 1 3/4", 1 7/8", 2" | Steel | Plastic Case | 00000000 | 000000 |
For Hole Dia. | Material | Each | |
1/8" | Steel | 00000000 | 000000 |
3/16" | Steel | 00000000 | 00000 |
1/4" | Steel | 00000000 | 00000 |
5/16" | Steel | 00000000 | 00000 |
3/8" | Steel | 00000000 | 00000 |
7/16" | Steel | 00000000 | 00000 |
1/2" | Steel | 00000000 | 00000 |
9/16" | Steel | 00000000 | 00000 |
5/8" | Steel | 00000000 | 00000 |
3/4" | Steel | 00000000 | 00000 |
7/8" | Steel | 00000000 | 00000 |
1" | Steel | 00000000 | 00000 |
1 1/16" | Steel | 00000000 | 00000 |
1 1/8" | Steel | 00000000 | 00000 |
1 3/16" | Steel | 00000000 | 00000 |
1 1/4" | Steel | 00000000 | 00000 |
1 5/16" | Steel | 00000000 | 00000 |
1 3/8" | Steel | 00000000 | 00000 |
1 7/16" | Steel | 00000000 | 00000 |
1 1/2" | Steel | 00000000 | 00000 |
1 5/8" | Steel | 00000000 | 00000 |
1 11/16" | Steel | 00000000 | 00000 |
1 3/4" | Steel | 00000000 | 00000 |
1 7/8" | Steel | 00000000 | 00000 |
2" | Steel | 00000000 | 00000 |
Economy Hammer-Driven Gasket and Washer Punch Sets
This set includes common ID and OD sizes to create gaskets and washers in two strikes.
For technical drawings and 3-D models, click on a part number.
Includes | For Hole Dia. | Material | Container Type | Each | |
For Use On Brass, Cork, Fabric, Leather, Plastic, Rubber | |||||
---|---|---|---|---|---|
10 Punches, Handle | 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", 7/8", 1" | Steel | Plastic Case | 0000000 | 000000 |
Quick-Release Hammer-Driven Gasket and Washer Punch Sets
Quickly switch between inner and outer punches to create washers faster than with standard sets.
For technical drawings and 3-D models, click on a part number.
Includes | For Hole Dia. | Material | Container Type | Each | |
For Use On Cork, Fabric, Fiberglass, Leather, Plastic, Rubber | |||||
---|---|---|---|---|---|
13 Punches, Centering Pin, Handle, Punch Cutting Pad | 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16", 7/8", 15/16", 1" | Steel | Plastic Case | 0000000 | 0000000 |
Self-Aligning Hammer-Driven Gasket and Washer Punch Sets for Thin Materials
For accurate punching of inner and outer holes, these sets come with pilots that attach to the outer hole punch.
Includes | For Hole Dia. | Pilot Dia. | For Max. Steel Thick. | Material | Container Type | Each | |
For Use On Aluminum, Brass, Copper, Cork, Fiberglass, Iron, Leather, Plastic, Rubber, Stainless Steel, Steel | |||||||
---|---|---|---|---|---|---|---|
9 Punches, 8 Pilots | 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 5/8", 3/4" | 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 5/8" | 1/64" | Steel | Plastic Case | 0000000 | 0000000 |
Hammer-Driven Gasket and Washer Punch Sets for Thin Materials
Slide thin sheets of material into the included die block then punch an inner and outer hole to create a shim or washer.
Includes | For Hole Dia. | For Max. Steel Thick. | Material | Container Type | Each | |
For Use On Aluminum, Brass, Copper, Cork, Fabric, Fiberglass, Iron, Leather, Plastic, Rubber, Stainless Steel, Steel | ||||||
---|---|---|---|---|---|---|
9 Punches | 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 5/8", 3/4" | 1/64" | Steel | Plastic Case | 0000000 | 0000000 |
Hammer-Driven Hole Punch Sets
The handle and punch are one complete tool.
For technical drawings and 3-D models, click on a part number.
Includes | For Hole Dia. | Material | Container Type | Each | |
For Use On Brass, Copper, Fabric, Leather, Rubber | |||||
---|---|---|---|---|---|
7 Punches | 3/16", 5/16", 7/16", 9/16", 11/16", 13/16", 15/16" | Steel | Nylon Pouch | 0000000 | 0000000 |
For Use On Brass, Copper, Cork, Fabric, Leather, Rubber | |||||
6 Punches | 3/16", 1/4", 5/16", 3/8", 7/16", 1/2" | Steel | Plastic Pouch | 0000000 | 00000 |
Hand-Driven Hole Punch Sets
This set includes all six sizes of our individually sold hand-driven hole punches plus a tool to remove punched out material. Turn the handle of these punches while pushing down to punch holes in cork and rubber. Also known as cork borers, these tools have precision-ground edges that can be sharpened.
Includes | For Hole Dia. | Lg. | Material | Handle Material | Each | |
For Use On Cork, Rubber | ||||||
---|---|---|---|---|---|---|
6 Punches, Material Removal Tool | 3/16", 1/4", 5/16", 3/8", 7/16", 1/2" | 4 1/2" | Zinc-Plated Brass | Plastic | 0000000 | 000000 |
Hand-Driven Hole Punches
Turn the handle of these punches while pushing down to punch holes in cork and rubber. Also known as cork borers, these tools have precision-ground edges that can be sharpened.
For Hole Dia. | Lg. | Material | Handle Material | Each | |
For Use On Cork, Rubber | |||||
---|---|---|---|---|---|
7/16" | 4 1/2" | Zinc-Plated Brass | Plastic | 0000000 | 000000 |
Hydraulic Hole Punches
Our strongest punch, this tool has 35 tons of force to punch through tough materials such as bus bars, railings, and I-beams. It requires a 10,000 psi hydraulic pump (sold separately).
For Hole Dia. | For Max. Steel Thick. | Punching Force, lbs. | Throat Dp. | Ht. | Wd. | Dp. | Material | Includes | Each | |
For Use On Aluminum, Brass, Copper, Steel | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
7/16", 9/16", 11/16", 13/16" | 1/2" | 70,000 | 2 3/4" | 14" | 3 1/2" | 8" | Steel | 4 Punches, 4 Dies | 0000000 | 000000000 |
Max. Air Pressure, psi | Power, hp | Voltage | Frequency, Hz | Ht. | Wd. | Dp. | Power Source | Cord Lg., ft. | Plug Type | Includes | Each | |
10,000 | 1/2 | 120V AC | 60 | 15 1/2" | 10 1/2" | 9 1/2" | Plug In | 16 | Three Prong | 10-ft. Hydraulic Hose, Fittings, Hydraulic Oil, Pump Controls with 10-ft. Cable | 0000000 | 000000000 |
Hammer-Driven Cutting Punches for Grommets
Punch a hole in your material to prepare for the installation of fabric grommets. Strike these tools with a wooden or rawhide mallet.
For Grommet Trade Size | For Hole Dia. | Material | For Use On | Each | |
3 | 7/16" | Steel | Fabric, Leather, Plastic | 0000000 | 000000 |
Hammer-Driven Installation Punches for Grommets
These punches set grommets that have a standard washer or a tooth lock washer. Strike the punch with a wooden or rawhide mallet. Punch and die are stamped with the corresponding grommet trade size.
For Grommet Trade Size | For Hole Dia. | Each | |
3 | 7/16" | 0000000 | 000000 |
Hammer-Driven Installation Punches for Grommets with Extended-Neck Washer
These punches set grommets that have an extended-neck washer or an extended-neck tooth lock washer. Strike the punch with a wooden or rawhide mallet. Punch and die are stamped with the corresponding grommet trade size.
For Grommet Trade Size | For Hole Dia. | Each | |
2 | 7/16" | 0000000 | 000000 |