Hammer-Driven Hole Punches
Strengthened edges cut holes in soft metal. These punches are also known as arch punches.
For technical drawings and 3-D models, click on a part number.
For Hole Dia. | Lg. | Material | Each | |
For Use On Brass, Copper, Fabric, Leather, Rubber | ||||
---|---|---|---|---|
7/8" | 5 1/4" | Steel | 0000000 | 000000 |
Hammer-Driven Small Hole Punches
Use these punches to make round holes in soft, nonmetallic materials.
For technical drawings and 3-D models, click on a part number.
For Hole Dia. | Lg. | Material | Each | |
For Use On Fabric, Leather, Rubber | ||||
---|---|---|---|---|
7/8" | 5" | Steel | 0000000 | 000000 |
One-Step Hammer-Driven Gasket and Washer Punch Sets
Attach two punch heads to the handle at the same time to punch a gasket or washer in a single strike.
Includes | For Hole Dia. | Material | Container Type | Each | |
For Use On Aluminum, Cork, Fabric, Leather, Plastic, Rubber | |||||
---|---|---|---|---|---|
15 Punches, Handle | 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", 7/8", 1", 1 1/16", 1 1/8", 1 3/16" | Steel | Plastic Case | 00000000 | 0000000 |
25 Punches, Handle | 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", 7/8", 1", 1 1/16", 1 1/8", 1 3/16", 1 1/4", 1 5/16", 1 3/8", 1 7/16", 1 1/2", 1 5/8", 1 11/16", 1 3/4", 1 7/8", 2" | Steel | Plastic Case | 00000000 | 000000 |
For Hole Dia. | Material | Each | |
1/8" | Steel | 00000000 | 000000 |
3/16" | Steel | 00000000 | 00000 |
1/4" | Steel | 00000000 | 00000 |
5/16" | Steel | 00000000 | 00000 |
3/8" | Steel | 00000000 | 00000 |
7/16" | Steel | 00000000 | 00000 |
1/2" | Steel | 00000000 | 00000 |
9/16" | Steel | 00000000 | 00000 |
5/8" | Steel | 00000000 | 00000 |
3/4" | Steel | 00000000 | 00000 |
7/8" | Steel | 00000000 | 00000 |
1" | Steel | 00000000 | 00000 |
1 1/16" | Steel | 00000000 | 00000 |
1 1/8" | Steel | 00000000 | 00000 |
1 3/16" | Steel | 00000000 | 00000 |
1 1/4" | Steel | 00000000 | 00000 |
1 5/16" | Steel | 00000000 | 00000 |
1 3/8" | Steel | 00000000 | 00000 |
1 7/16" | Steel | 00000000 | 00000 |
1 1/2" | Steel | 00000000 | 00000 |
1 5/8" | Steel | 00000000 | 00000 |
1 11/16" | Steel | 00000000 | 00000 |
1 3/4" | Steel | 00000000 | 00000 |
1 7/8" | Steel | 00000000 | 00000 |
2" | Steel | 00000000 | 00000 |
Economy Hammer-Driven Gasket and Washer Punch Sets
This set includes common ID and OD sizes to create gaskets and washers in two strikes.
For technical drawings and 3-D models, click on a part number.
Includes | For Hole Dia. | Material | Container Type | Each | |
For Use On Brass, Cork, Fabric, Leather, Plastic, Rubber | |||||
---|---|---|---|---|---|
10 Punches, Handle | 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", 7/8", 1" | Steel | Plastic Case | 0000000 | 000000 |
Quick-Release Hammer-Driven Gasket and Washer Punch Sets
Quickly switch between inner and outer punches to create washers faster than with standard sets.
For technical drawings and 3-D models, click on a part number.
Includes | For Hole Dia. | Material | Container Type | Each | |
For Use On Cork, Fabric, Fiberglass, Leather, Plastic, Rubber | |||||
---|---|---|---|---|---|
7 Punches, Centering Pin, Handle, Punch Cutting Pad | 1/4", 3/8", 1/2", 5/8", 3/4", 7/8", 1" | Steel | Plastic Case | 0000000 | 0000000 |
13 Punches, Centering Pin, Handle, Punch Cutting Pad | 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16", 7/8", 15/16", 1" | Steel | Plastic Case | 0000000 | 000000 |
Self-Aligning Hammer-Driven Gasket and Washer Punch Sets for Thin Materials
For accurate punching of inner and outer holes, these sets come with pilots that attach to the outer hole punch.
Includes | For Hole Dia. | Pilot Dia. | For Max. Steel Thick. | Material | Container Type | Each | |
For Use On Aluminum, Brass, Copper, Cork, Fiberglass, Iron, Leather, Plastic, Rubber, Stainless Steel, Steel | |||||||
---|---|---|---|---|---|---|---|
4 Punches, 4 Pilots | 7/8", 1", 1 1/8", 1 1/4" | 3/4", 7/8", 1", 1 1/8" | 1/64" | Steel | Plastic Case | 0000000 | 0000000 |
Hammer-Driven Hole Punch Sets
The handle and punch are one complete tool.
For technical drawings and 3-D models, click on a part number.
Stud-Driven Round Hole Punches
Create holes in metal, plastic, and fiberglass by using a wrench or driver to draw the punch onto the included stud. Drill pilot holes slightly larger than the size of the stud. These punches are also known as knockout and chassis punches.
Hole Punches | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Stud | Replacement Studs | Replacement Dies | Replacement Punches | |||||||||||
For Conduit Trade Size | For Hole Dia. | For Max. Steel Thick. | Dia. | Lg. | Material | Includes | Each | Each | Each | Each | ||||
For Use On Aluminum, Brass, Copper, Fiberglass, Plastic, Steel | ||||||||||||||
1/2 | 7/8" | 1/8" | 7/16" | 3" | Steel | Punch, Die, Stud | 000000000 | 000000 | 000000000 | 000000 | 00000000 | 000000 | 00000000 | 000000 |
Stud-Driven Round Hole Punches for Pipe and Conduit
Create holes in metal, plastic, and fiberglass by using a wrench or driver to draw the punch onto the included stud. Drill pilot holes slightly larger than the size of the stud. These punches are also known as knockout and chassis punches.
Hole Punches | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Stud | Replacement Studs | Replacement Dies | Replacement Punches | ||||||||||||
For Pipe Size | For Hole Dia. | For Conduit Trade Size | For Max. Steel Thick. | Dia. | Lg. | Material | Includes | Each | Each | Each | Each | ||||
For Use On Aluminum, Brass, Copper, Fiberglass, Plastic, Steel | |||||||||||||||
1/2 | 7/8" | 1/2 | 1/8" | 7/16" | 3" | Steel | Punch, Die, Stud | 000000000 | 000000 | 000000000 | 000000 | 00000000 | 000000 | 00000000 | 000000 |
Self-Centering Stud-Driven Round Hole Punches
Make accurate holes every time. Drill a pilot hole into your workpiece—the center of these punches fits inside the pilot hole to keep cuts aligned. The pilot hole should be slightly larger than the size of the stud. The die’s design splits the punched out plug in two for easy removal. All punches require a hydraulic driver. They are also known as knockout and chassis punches.
For Conduit Trade Size | For Hole Dia. | For Panel Cutout Dia., mm | For Max. Steel Thick. | Material | Includes | Each | |
For Use On Aluminum, Brass, Copper, Stainless Steel, Steel | |||||||
---|---|---|---|---|---|---|---|
1/2 | 7/8" | 22 | 1/8" | Steel | Punch, Die, Stud | 0000000 | 0000000 |
Self-Centering Stud-Driven Round Hole Punches for Pipe and Conduit
Make accurate holes every time. Drill a pilot hole into your workpiece—the center of these punches fits inside the pilot hole to keep cuts aligned. The pilot hole should be slightly larger than the size of the stud. The die’s design splits the punched out plug in two for easy removal. These are also known as knockout and chassis punches. These punches require a hydraulic driver.
For Pipe Size | For Conduit Trade Size | For Hole Dia. | For Panel Cutout Dia., mm | For Max. Steel Thick. | Material | Includes | Each | |
For Use On Aluminum, Brass, Copper, Stainless Steel, Steel | ||||||||
---|---|---|---|---|---|---|---|---|
1/2 | 1/2 | 7/8" | 22 | 1/8" | Steel | Punch, Die, Stud | 0000000 | 0000000 |
Metric Self-Centering Stud-Driven Round Hole Punches for Conduit
Make accurate holes every time. Drill a pilot hole into your workpiece—the center of these punches fits inside the pilot hole to keep cuts aligned. The pilot hole should be slightly larger than the size of the stud. The die’s design splits the punched out plug in two for easy removal. These are also known as knockout and chassis punches. These punches can be used with any 8- or 11-ton hydraulic driver.
For Hole Dia. | For Panel Cutout Dia., mm | For Max. Steel Thick. | Material | Includes | Each | |
For Use On Aluminum, Brass, Copper, Stainless Steel, Steel | ||||||
---|---|---|---|---|---|---|
7/8" | 22 | 1/8" | Steel | Punch, Die, Stud | 0000000 | 0000000 |
Hammer-Driven Cutting Punches for Grommets
Punch a hole in your material to prepare for the installation of fabric grommets. Strike these tools with a wooden or rawhide mallet.
For Grommet Trade Size | For Hole Dia. | Material | For Use On | Each | |
7 | 7/8" | Steel | Fabric, Leather, Plastic | 0000000 | 000000 |