These clamps are easier to install than worm-drive clamps—crimp the pinch points with pinch-clamp pincers for a secure hold. They are also known as ear clamps.

A double ring of thick wire provides a complete seal around large-diameter hose.

Not as bulky as our other constant-tension clamps, these round-wire clamps easily fit in cramped spaces. Use in low-pressure applications.

The end of the band curls back into the buckle—this gives these clamps up to 25% more strength than other low-profile clamps. They are also known as JS-style clamps.

Designed for both permanent connections and emergency repairs, use these buckles with banding to create your own low-profile hose clamps.

The bolt design provides high strength and creates a 360° seal to prevent leaks.

Flip the toggle latch to install and remove these clamps in seconds.

Floor-mount brackets swivel 345°. Beam-mount brackets easily mount overhead on I-beams or H-beams. Wall-mount brackets pivot 180°

Bolt or weld these rails to the mounting surface, then attach clamps with a rail nut.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.

For areas with low clearance, these clamps have the mounting fastener to the side of the material, rather than on top.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.

Use these clamps to route insulated pipe through floors. They have a plastic insert that creates a seal around the pipe's insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.

Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.

Reduce movement in your line with hangers that are more rigid than strap hangers and fit tighter around pipe, conduit, and tube than loop hangers.

Use these close-fitting hangers for a more rigid hold around material than when using straps alone.

Mount these beams across parallel roof joists to hang threaded rod and route pipe, duct, and other overhead systems in areas where there’s no anchoring point.

Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.

Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.

Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.

Temporarily mount routing rings and other threaded components to steel and iron surfaces.

Hang these S-hooks from fencing and railing to route large bundles of material, such as cable, hose, and wire through your facility or worksite to avoid tripping hazards.

Hang cable and other flexible material beneath wire to prevent it from sagging and swaying. To install, hook the two ends of the ring around the wire—no fasteners required.

The tips adjust to accommodate the clamps often found on heater and radiator hoses.

Curved, serrated jaws firmly grip hose and tube for installation and removal without damage.

Use these accessories to mount carriers to your machinery without creating an obstruction.

Cut, bend, and connect these wire mesh tray systems to route cable and hose in configurations such as curves, slopes, and tees.