About Measuring Hose and Tube Clamps
What's the best way to determine the clamp size you'll need? Simply measure the outside diameter of your hose with the fitting installed. Some clamps accommodate a range of sizes, so be sure the size you need falls in the middle of that range.
More
Low-Profile Band Clamps for Firm Hose
Easier to install than our Extra-Strength Low-Profile Band Clamps, these clamps seal with a quick hammer blow to the buckle. They are also known as center-punch clamps.
Unlike worm-drive clamps and bolt clamps, these have a low profile with no protruding parts to get in your way during installation. The banding is double wrapped for extra strength. Use them to secure firm plastic and rubber hose, coaxial cable, and rope. Clamps require an installation tool (sold separately).
Galvanized steel clamps offer fair corrosion resistance.
201 and 300 series stainless steel clamps have very good corrosion resistance.
Note: When choosing a clamp, measure the outside diameter of your hose with the fitting installed.
For technical drawings and 3-D models, click on a part number.
Clamp ID Range | Band | Temperature Range, °F | ||||||
|---|---|---|---|---|---|---|---|---|
| Inch | mm | Wd. | Thick. | Min. | Max. | Reusable | Each | |
Galvanized Steel with 201 Stainless Steel Buckle | ||||||||
| 5/8" to 13/16" | 15.9 to 20 | 3/8" | 0.025" | -100° | 300° | No | 0000000 | 00000 |
| 5/8" to 1 3/8" | 15.9 to 35 | 3/8" | 0.025" | -100° | 300° | No | 0000000 | 000 |
| 3/4" to 1" | 19.1 to 25 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 000 |
| 3/4" to 1 1/4" | 19.1 to 32 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 000 |
| 3/4" to 1 1/2" | 19.1 to 38 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 000 |
| 3/4" to 1 3/4" | 19.1 to 44 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 000 |
| 3/4" to 2" | 19.1 to 51 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 000 |
| 3/4" to 2 1/4" | 19.1 to 57 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 000 |
| 3/4" to 2 1/2" | 19.1 to 63 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 0000 |
| 3/4" to 2 3/4" | 19.1 to 70 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 0000 |
| 3/4" to 3" | 19.1 to 76 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 0000 |
| 3/4" to 3 1/2" | 19.1 to 89 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 0000 |
| 3/4" to 4" | 19.1 to 101 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 0000 |
| 3/4" to 4 1/2" | 19.1 to 114 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 0000 |
| 3/4" to 5" | 19.1 to 127 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 0000 |
| 3/4" to 6" | 19.1 to 152 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 0000 |
| 3/4" to 6 1/2" | 19.1 to 165 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 0000 |
| 3/4" to 7" | 19.1 to 178 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 0000 |
| 3/4" to 8" | 19.1 to 203 | 5/8" | 0.025" | -100° | 300° | No | 0000000 | 0000 |
201 Stainless Steel with 201 Stainless Steel Buckle | ||||||||
| 5/8" to 13/16" | 15.9 to 20 | 3/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 5/8" to 1 3/8" | 15.9 to 35 | 3/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 1" | 19.1 to 25 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 1 1/4" | 19.1 to 32 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 1 1/2" | 19.1 to 38 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 1 3/4" | 19.1 to 44 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 2" | 19.1 to 51 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 2 1/4" | 19.1 to 57 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 2 1/2" | 19.1 to 63 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 2 3/4" | 19.1 to 70 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 3" | 19.1 to 76 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 3 1/2" | 19.1 to 89 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 4" | 19.1 to 101 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 4 1/2" | 19.1 to 114 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 5" | 19.1 to 127 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 6" | 19.1 to 152 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 6 1/2" | 19.1 to 165 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 7" | 19.1 to 178 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
| 3/4" to 8" | 19.1 to 203 | 5/8" | 0.025" | -100° | 500° | No | 0000000 | 0000 |
300 Series Stainless Steel with 302 Stainless Steel Buckle | ||||||||
| 5/8" to 13/16" | 15.9 to 20 | 3/8" | 0.02" | Not Rated | 800° | No | 0000000 | 0000 |
| 5/8" to 1 3/8" | 15.9 to 35 | 3/8" | 0.02" | Not Rated | 800° | No | 0000000 | 0000 |
| 3/4" to 1" | 19.1 to 25 | 5/8" | 0.022" | Not Rated | 800° | No | 0000000 | 0000 |
| 3/4" to 1 1/4" | 19.1 to 32 | 5/8" | 0.022" | Not Rated | 800° | No | 0000000 | 0000 |
| 3/4" to 1 1/2" | 19.1 to 38 | 5/8" | 0.022" | Not Rated | 800° | No | 0000000 | 0000 |
| 3/4" to 1 3/4" | 19.1 to 44 | 5/8" | 0.022" | Not Rated | 800° | No | 0000000 | 0000 |
| 3/4" to 2" | 19.1 to 51 | 5/8" | 0.022" | Not Rated | 800° | No | 0000000 | 0000 |
| 3/4" to 2 1/4" | 19.1 to 57 | 5/8" | 0.022" | Not Rated | 800° | No | 0000000 | 0000 |
| 3/4" to 2 1/2" | 19.1 to 63 | 5/8" | 0.022" | Not Rated | 800° | No | 0000000 | 0000 |
| 3/4" to 2 3/4" | 19.1 to 70 | 5/8" | 0.022" | Not Rated | 800° | No | 0000000 | 0000 |
| 3/4" to 3" | 19.1 to 76 | 5/8" | 0.022" | Not Rated | 800° | No | 0000000 | 0000 |
| 3/4" to 3 1/2" | 19.1 to 89 | 5/8" | 0.022" | Not Rated | 800° | No | 0000000 | 0000 |
| 3/4" to 4" | 19.1 to 101 | 5/8" | 0.022" | Not Rated | 800° | No | 0000000 | 0000 |
| 3/4" to 4 1/2" | 19.1 to 114 | 5/8" | 0.022" | Not Rated | 800° | No | 0000000 | 0000 |
| 3/4" to 5" | 19.1 to 127 | 5/8" | 0.022" | Not Rated | 800° | No | 0000000 | 0000 |
| 3/4" to 6" | 19.1 to 152 | 5/8" | 0.022" | Not Rated | 800° | No | 0000000 | 0000 |
| 3/4" to 7" | 19.1 to 178 | 5/8" | 0.022" | Not Rated | 800° | No | 0000000 | 0000 |
| 3/4" to 8" | 19.1 to 203 | 5/8" | 0.022" | Not Rated | 800° | No | 0000000 | 0000 |
Extra-Strength Low-Profile Band Clamps for Firm Hose
The end of the band curls back into the buckle—this gives these clamps up to 25% more strength than other low-profile clamps. They are also known as JS-style clamps. Unlike worm-drive clamps and bolt clamps, these have a low profile with no protruding parts. A smooth interior prevents damage to the hose. Clamps are for firm plastic and rubber hose. They require an installation tool (sold separately).
Galvanized steel offers fair corrosion resistance.
201 stainless steel has good corrosion resistance.
316 stainless steel has excellent corrosion resistance.
Note: When choosing a clamp, measure the outside diameter of your hose with the fitting installed.
For technical drawings and 3-D models, click on a part number.
Clamp ID Range | Band | |||||||
|---|---|---|---|---|---|---|---|---|
| Inch | mm | Wd. | Thick. | Temperature Range, °F | Reusable | Specifications Met | Each | |
Galvanized Steel with 201 Stainless Steel Buckle | ||||||||
| 5/8" to 13/16" | 15.9 to 20 | 3/8" | 0.025" | -100° to 300° | No | SAE J1508 | 0000000 | 00000 |
| 5/8" to 1" | 15.9 to 25 | 3/8" | 0.025" | -100° to 300° | No | SAE J1508 | 0000000 | 000 |
| 5/8" to 1 3/8" | 15.9 to 35 | 3/8" | 0.025" | -100° to 300° | No | SAE J1508 | 0000000 | 000 |
| 5/8" to 2" | 15.9 to 50 | 3/8" | 0.025" | -100° to 300° | No | SAE J1508 | 0000000 | 000 |
| 3/4" to 1" | 19.1 to 25 | 1/2" | 0.03" | -100° to 300° | No | SAE J1508 | 0000000 | 000 |
| 3/4" to 1 1/4" | 19.1 to 32 | 1/2" | 0.03" | -100° to 300° | No | SAE J1508 | 0000000 | 000 |
| 1 1/4" to 1 1/2" | 32 to 38 | 5/8" | 0.03" | -100° to 300° | No | SAE J1508 | 0000000 | 0000 |
| 1 1/4" to 1 3/4" | 32 to 44 | 5/8" | 0.03" | -100° to 300° | No | SAE J1508 | 0000000 | 0000 |
| 1 1/4" to 2" | 32 to 51 | 5/8" | 0.03" | -100° to 300° | No | SAE J1508 | 0000000 | 0000 |
| 1 1/4" to 2 1/4" | 32 to 57 | 5/8" | 0.03" | -100° to 300° | No | SAE J1508 | 0000000 | 0000 |
| 1 1/4" to 2 1/2" | 32 to 63 | 5/8" | 0.03" | -100° to 300° | No | SAE J1508 | 0000000 | 0000 |
| 1 3/4" to 2 3/4" | 44 to 70 | 3/4" | 0.03" | -100° to 300° | No | SAE J1508 | 0000000 | 0000 |
| 1 3/4" to 3" | 44 to 76 | 3/4" | 0.03" | -100° to 300° | No | SAE J1508 | 0000000 | 0000 |
| 1 3/4" to 3 1/2" | 44 to 89 | 3/4" | 0.03" | -100° to 300° | No | SAE J1508 | 0000000 | 0000 |
| 1 3/4" to 4" | 44 to 101 | 3/4" | 0.03" | -100° to 300° | No | SAE J1508 | 0000000 | 0000 |
| 1 3/4" to 4 1/2" | 44 to 114 | 3/4" | 0.03" | -100° to 300° | No | SAE J1508 | 0000000 | 0000 |
| 1 3/4" to 5" | 44 to 127 | 3/4" | 0.03" | -100° to 300° | No | SAE J1508 | 0000000 | 0000 |
| 1 3/4" to 7" | 44 to 178 | 3/4" | 0.03" | -100° to 300° | No | SAE J1508 | 0000000 | 0000 |
201 Stainless Steel with 201 Stainless Steel Buckle | ||||||||
| 1/2" to 1 3/8" | 12.7 to 35 | 1/4" | 0.02" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 5/8" to 13/16" | 15.9 to 20 | 3/8" | 0.025" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 5/8" to 1" | 15.9 to 25 | 3/8" | 0.025" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 5/8" to 1 3/8" | 15.9 to 35 | 3/8" | 0.025" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 5/8" to 2" | 15.9 to 50 | 3/8" | 0.025" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 3/4" to 1" | 19.1 to 25 | 1/2" | 0.03" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 3/4" to 1 1/4" | 19.1 to 32 | 1/2" | 0.03" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 13/16" to 1" | 20.6 to 25.4 | 1/4" | 0.02" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 13/16" to 2" | 20.6 to 50.8 | 1/4" | 0.02" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 1 1/4" to 1 1/2" | 32 to 38 | 5/8" | 0.03" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 1 1/4" to 1 3/4" | 32 to 44 | 5/8" | 0.03" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 1 1/4" to 2" | 32 to 51 | 5/8" | 0.03" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 1 1/4" to 2 1/4" | 32 to 57 | 5/8" | 0.03" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 1 1/4" to 2 1/2" | 32 to 63 | 5/8" | 0.03" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 1 3/4" to 2 3/4" | 44 to 70 | 3/4" | 0.03" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 1 3/4" to 3" | 44 to 76 | 3/4" | 0.03" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 1 3/4" to 3 1/2" | 44 to 89 | 3/4" | 0.03" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 1 3/4" to 4" | 44 to 101 | 3/4" | 0.03" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 1 3/4" to 4 1/2" | 44 to 114 | 3/4" | 0.03" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 1 3/4" to 5" | 44 to 127 | 3/4" | 0.03" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 1 3/4" to 6" | 44 to 152 | 3/4" | 0.03" | -100° to 500° | No | SAE J1508 | 0000000 | 0000 |
| 1 3/4" to 7" | 44 to 178 | 3/4" | 0.03" | -100° to 500° | No | SAE J1508 | 0000000 | 00000 |
316 Stainless Steel with 316 Stainless Steel Buckle | ||||||||
| 5/8" to 13/16" | 15.9 to 20 | 3/8" | 0.025" | -100° to 600° | No | SAE J1508 | 0000000 | 0000 |
| 5/8" to 1 3/8" | 15.9 to 35 | 3/8" | 0.025" | -100° to 600° | No | SAE J1508 | 0000000 | 0000 |
| 5/8" to 2" | 15.9 to 50 | 3/8" | 0.025" | -100° to 600° | No | SAE J1508 | 0000000 | 0000 |
| 3/4" to 1 1/4" | 19.1 to 32 | 1/2" | 0.03" | -100° to 600° | No | SAE J1508 | 0000000 | 0000 |
| 1 1/4" to 1 1/2" | 32 to 38 | 5/8" | 0.03" | -100° to 600° | No | SAE J1508 | 0000000 | 0000 |
| 1 1/4" to 1 3/4" | 32 to 44 | 5/8" | 0.03" | -100° to 600° | No | SAE J1508 | 0000000 | 00000 |
| 1 1/4" to 2 1/2" | 32 to 63 | 5/8" | 0.03" | -100° to 600° | No | SAE J1508 | 0000000 | 00000 |
| 1 3/4" to 3" | 44 to 76 | 3/4" | 0.03" | -100° to 600° | No | SAE J1508 | 0000000 | 00000 |
| 1 3/4" to 4" | 44 to 101 | 3/4" | 0.03" | -100° to 600° | No | SAE J1508 | 0000000 | 00000 |
| 1 3/4" to 4 1/2" | 44 to 114 | 3/4" | 0.03" | -100° to 600° | No | SAE J1508 | 0000000 | 00000 |
| 1 3/4" to 5" | 44 to 127 | 3/4" | 0.03" | -100° to 600° | No | SAE J1508 | 0000000 | 00000 |
| Each | ||
| Wing-Handle Installation Tool | 0000000 | 0000000 |
Banding for Build-Your-Own Low-Profile Band Clamps for Firm Hose
Keep this banding on hand for both permanent connections and emergency repairs. You'll need an installation tool and a buckle (both sold separately) to create a band clamp. Banding comes in a dispenser carton. It has smooth, rounded edges to protect your hose from cuts.
Galvanized steel banding has fair corrosion resistance.
201 stainless steel banding has good corrosion resistance.
304 stainless steel banding has very good corrosion resistance.
316 stainless steel banding has excellent corrosion resistance.
Black polyester-coated 201 stainless steel banding has excellent abrasion and UV resistance.
Note: The breaking strength listed is the maximum tension that can be applied to the banding. For an extra-strong clamp, wrap the banding around twice, threading it through the buckle each time.
For technical drawings and 3-D models, click on a part number.
Band | 100-ft. Lg. | 200-ft. Lg. | |||||
|---|---|---|---|---|---|---|---|
| Wd. | Thick. | Breaking Strength, lbs. | Reusable | Each | Each | ||
Galvanized Steel | |||||||
| 1/2" | 0.03" | 1,125 | No | 0000000 | 000000 | 000000 | 00 |
| 5/8" | 0.03" | 1,400 | No | 0000000 | 00000 | 000000 | 00 |
| 3/4" | 0.03" | 1,600 | No | 0000000 | 000000 | 000000 | 00 |
201 Stainless Steel  | |||||||
| 1/4" | 0.02" | 500 | No | 0000000 | 00000 | 000000 | 00 |
| 3/8" | 0.025" | 900 | No | 0000000 | 000000 | 000000 | 00 |
| 1/2" | 0.03" | 1,500 | No | 0000000 | 000000 | 000000 | 00 |
| 5/8" | 0.03" | 1,800 | No | 0000000 | 000000 | 000000 | 00 |
| 3/4" | 0.03" | 2,250 | No | 0000000 | 000000 | 000000 | 00 |
| 3/4" | 0.044" | 3,300 | No | 0000000 | 000000 | 000000 | 00 |
| 1" | 0.044" | 4,400 | No | 0000000 | 000000 | 000000 | 00 |
| 1 1/4" | 0.044" | 5,500 | No | 0000000 | 000000 | 000000 | 00 |
304 Stainless Steel | |||||||
| 3/8" | 0.02" | 600 | No | 000000 | 00 | 0000000 | 0000000 |
| 1/2" | 0.02" | 850 | No | 000000 | 00 | 0000000 | 000000 |
| 5/8" | 0.02" | 1,000 | No | 000000 | 00 | 0000000 | 000000 |
| 3/4" | 0.02" | 1,275 | No | 000000 | 00 | 0000000 | 000000 |
316 Stainless Steel | |||||||
| 1/4" | 0.02" | 400 | No | 0000000 | 000000 | 000000 | 00 |
| 3/8" | 0.025" | 750 | No | 0000000 | 000000 | 000000 | 00 |
| 1/2" | 0.03" | 1,200 | No | 0000000 | 000000 | 000000 | 00 |
| 5/8" | 0.03" | 1,500 | No | 0000000 | 000000 | 000000 | 00 |
| 3/4" | 0.03" | 1,800 | No | 0000000 | 000000 | 000000 | 00 |
Black Polyester-Coated 201 Stainless Steel | |||||||
| 3/4" | 0.03" | 2,250 | No | 0000000 | 000000 | 000000 | 00 |
Buckles for Build-Your-Own Low-Profile Band Clamps for Firm Hose
Designed for both permanent connections and emergency repairs, use these buckles with banding to create your own low-profile hose clamps.
Clip On—Buckles have ears for strong, reliable clamping.
Clip On with Teeth—Buckles have teeth, as well as ears, for extra gripping power.
Set Screw—Buckles are reusable.
Galvanized steel buckles have fair corrosion resistance.
201 stainless steel buckles have good corrosion resistance.
316 stainless steel buckles have excellent corrosion resistance.
For technical drawings and 3-D models, click on a part number.
For Band | |||||
|---|---|---|---|---|---|
| Wd. | Thick. | Reusable | Pkg. Qty. | Pkg. | |
Clip On | |||||
201 Stainless Steel | |||||
| 1/4" | 0.02" | No | 1 | 0000000 | 00000 |
| 1/4" | 0.02" | No | 100 | 0000000 | 00000 |
316 Stainless Steel | |||||
| 1/4" | 0.02" | No | 1 | 0000000 | 0000 |
| 1/4" | 0.02" | No | 100 | 0000000 | 000000 |
Clip On with Teeth | |||||
Galvanized Steel | |||||
| 1/2" | 0.03" | No | 1 | 0000000 | 0000 |
| 1/2" | 0.03" | No | 100 | 0000000 | 00000 |
| 5/8" | 0.03" | No | 1 | 0000000 | 0000 |
| 5/8" | 0.03" | No | 100 | 0000000 | 00000 |
| 3/4" | 0.03" | No | 5 | 0000000 | 0000 |
| 3/4" | 0.03" | No | 100 | 0000000 | 00000 |
201 Stainless Steel | |||||
| 3/8" | 0.025" | No | 1 | 0000000 | 0000 |
| 3/8" | 0.025" | No | 100 | 0000000 | 00000 |
| 1/2" | 0.03" | No | 1 | 0000000 | 0000 |
| 1/2" | 0.03" | No | 100 | 0000000 | 00000 |
| 5/8" | 0.03" | No | 1 | 0000000 | 0000 |
| 5/8" | 0.03" | No | 100 | 0000000 | 000000 |
| 3/4" | 0.03" | No | 1 | 0000000 | 0000 |
| 3/4" | 0.03" | No | 100 | 0000000 | 000000 |
| 3/4" | 0.044" | No | 1 | 0000000 | 0000 |
| 3/4" | 0.044" | No | 25 | 0000000 | 000000 |
| 1" | 0.044" | No | 1 | 0000000 | 0000 |
| 1" | 0.044" | No | 25 | 0000000 | 000000 |
| 1 1/4" | 0.044" | No | 1 | 0000000 | 0000 |
| 1 1/4" | 0.044" | No | 25 | 0000000 | 000000 |
316 Stainless Steel | |||||
| 3/8" | 0.025" | No | 1 | 0000000 | 0000 |
| 3/8" | 0.025" | No | 100 | 0000000 | 000000 |
| 1/2" | 0.03" | No | 1 | 0000000 | 0000 |
| 1/2" | 0.03" | No | 100 | 0000000 | 000000 |
| 5/8" | 0.03" | No | 1 | 0000000 | 0000 |
| 5/8" | 0.03" | No | 100 | 0000000 | 000000 |
| 3/4" | 0.03" | No | 1 | 0000000 | 0000 |
| 3/4" | 0.03" | No | 100 | 0000000 | 000000 |
| Each | |||||
Set Screw | |||||
201 Stainless Steel | |||||
| 1/4" | 0.02" | Yes | __ | 0000000 | 0000 |
| 3/8" | 0.025" | Yes | __ | 0000000 | 0000 |
| 1/2" | 0.03" | Yes | __ | 0000000 | 0000 |
| 5/8" | 0.03" | Yes | __ | 0000000 | 0000 |
| 3/4" | 0.044" | Yes | __ | 0000000 | 0000 |
General Purpose Bolt Clamps for Firm Hose
One clamp fits a wide range of diameters, so you can always have the right size on hand. Clamps are for firm plastic and rubber hose. Do not exceed the maximum torque or clamps may be damaged.
Smooth Band—Clamps lock with a screw on the banding.
Slotted Band—Clamps lock with a screw on the banding and a notch in the slot.
Galvanized steel and zinc-plated steel have fair corrosion resistance.
301 and 305 stainless steel have very good corrosion resistance.
Note: When choosing a clamp, measure the outside diameter of your hose or tube with the fitting installed.
For technical drawings and 3-D models, click on a part number.
Clamp ID Range | Band | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Inch | mm | Wd. | Thick. | Temp. Range, ° F | Max. Torque, in.-lbs. | Hex Size | Reusable | Specifications Met | Each | |
Smooth Band | ||||||||||
Galvanized Steel with Zinc-Plated Steel Bolt | ||||||||||
| 1" to 3 1/2" | 25 to 89 | 1/2" | 0.017" | -40° to 375° | 20 | 5/16" | No | __ | 000000 | 00000 |
| 1" to 4 1/2" | 25 to 114 | 1/2" | 0.017" | -40° to 375° | 20 | 5/16" | No | __ | 000000 | 0000 |
| 1" to 5" | 25 to 127 | 1/2" | 0.017" | -40° to 375° | 20 | 5/16" | No | __ | 000000 | 0000 |
| 1" to 7" | 25 to 178 | 1/2" | 0.017" | -40° to 375° | 20 | 5/16" | No | __ | 000000 | 0000 |
| 1" to 9" | 25 to 229 | 1/2" | 0.017" | -40° to 375° | 20 | 5/16" | No | __ | 000000 | 0000 |
| 1" to 14 1/2" | 25 to 368 | 1/2" | 0.017" | -40° to 375° | 20 | 5/16" | No | __ | 000000 | 0000 |
Slotted Band | ||||||||||
301 Stainless Steel with Zinc-Plated 305 Stainless Steel Bolt | ||||||||||
| 11/16" to 2 5/8" | 17 to 67 | 1/2" | 0.015" | -40° to 375° | 20 | 5/16" | No | Fed. Spec. WW-C-440B, IPC Compliant, SAE J1508 | 0000000 | 0000 |
| 1 3/4" to 5" | 44 to 127 | 1/2" | 0.015" | -40° to 375° | 20 | 5/16" | No | Fed. Spec. WW-C-440B, IPC Compliant, SAE J1508 | 0000000 | 0000 |
| 4" to 7 1/4" | 102 to 184 | 1/2" | 0.015" | -40° to 375° | 20 | 5/16" | No | Fed. Spec. WW-C-440B, IPC Compliant, SAE J1508 | 0000000 | 0000 |
Wide-Seal Plastic Clamps for Firm Hose
Slide these clamps over your hose and heat-shrink them with a heavy duty heat gun (not included). This process lets them conform to any shape hose. Clamps never need tightening because when the hose contracts with cold temperatures, the clamps adjust themselves to maintain tension. Use clamps with firm plastic and rubber coolant hose; however, they are not recommended for use with wire-reinforced coolant hose.
Note: When choosing a clamp, measure the outside diameter of your hose with the fitting installed.
The removal tool (sold separately) is spring loaded to quickly cut through the clamp without damaging the hose. Slip the blade below the clamp and squeeze for easy removal.
For technical drawings and 3-D models, click on a part number.
Clamp ID Range | Band | |||||||
|---|---|---|---|---|---|---|---|---|
| Inch | mm | Wd. | Thick. | Temperature Range, ° F | Color | Reusable | Each | |
Plastic | ||||||||
| 1/2" to 11/16" | 12.7 to 17.5 | 3/4" | 0.075" | -40° to 300° | Black | No | 0000000 | 00000 |
| 11/16" to 13/16" | 17.5 to 20.6 | 3/4" | 0.075" | -40° to 300° | Black | No | 0000000 | 0000 |
| 13/16" to 15/16" | 20.6 to 23.8 | 3/4" | 0.065" | -40° to 300° | Black | No | 0000000 | 0000 |
| 15/16" to 1 1/16" | 23.8 to 27 | 1" | 0.065" | -40° to 300° | Black | No | 0000000 | 0000 |
| 1 1/16" to 1 3/16" | 27 to 30.2 | 1" | 0.065" | -40° to 300° | Black | No | 0000000 | 0000 |
| 1 3/16" to 1 5/16" | 30.2 to 33.3 | 1" | 0.09" | -40° to 300° | Black | No | 0000000 | 0000 |
| 1 5/16" to 1 1/2" | 33.3 to 38.1 | 1" | 0.065" | -40° to 300° | Black | No | 0000000 | 0000 |
| 1 1/2" to 1 3/4" | 38.1 to 44.5 | 1 1/4" | 0.065" | -40° to 300° | Black | No | 0000000 | 0000 |
| 1 3/4" to 2" | 44.5 to 50.8 | 1 1/4" | 0.065" | -40° to 300° | Black | No | 0000000 | 0000 |
| 2" to 2 1/4" | 50.8 to 57.2 | 1 1/4" | 0.065" | -40° to 300° | Black | No | 0000000 | 0000 |
| 2 1/4" to 2 1/2" | 57.2 to 63.5 | 1 1/4" | 0.065" | -40° to 300° | Black | No | 0000000 | 0000 |
| 2 1/2" to 2 3/4" | 63.5 to 69.9 | 1 1/2" | 0.085" | -40° to 300° | Black | No | 0000000 | 0000 |
| 2 3/4" to 3" | 69.9 to 76.2 | 1 1/2" | 0.085" | -40° to 300° | Black | No | 0000000 | 0000 |
| 3" to 3 1/4" | 76.2 to 82.6 | 1 1/2" | 0.085" | -40° to 300° | Black | No | 0000000 | 0000 |
| 3 1/4" to 3 1/2" | 82.6 to 88.9 | 1 1/2" | 0.09" | -40° to 300° | Black | No | 0000000 | 00000 |
| 3 1/2" to 3 5/8" | 88.9 to 92.1 | 1 1/2" | 0.09" | -40° to 300° | Black | No | 0000000 | 00000 |
| Material | Opening Style | Each | |
| Steel | Spring Assisted | 0000000 | 0000000 |
Guards for Hose and Tube Clamps
Cover the ends of hose and tube clamps to prevent them from cutting people and nearby objects. Made of flexible TPE plastic, these guards can be cut to size for shorter bands or T-bolts.
For technical drawings and 3-D models, click on a part number.
