Even at high temperatures, these tubes remain flexible to stretch over components without tearing. They restrict absorption of water, air, and gas and are typically used on hot and cold water lines and electrical components.

Hook-and-loop fasteners make it easy to install, remove, and reuse this flexible insulation. Use on steam, hot water, and process pipes and fittings.

Melamine has a lightweight construction that allows quick and easy installation. Use on cold and hot water piping and with refrigeration systems.

These rigid, lightweight melamine foam tubes are wrapped in an ISO Class 5 and Fed. Spec. Class 100 clean room jacket that is suitable for sanitary and washdown applications. They’re typically used on cold and hot water piping and with refrigeration systems.

These kits insulate one P-trap and two stop valves to reduce the risk of burns from accidental contact with hot pipes under your sink. The molded, flexible pipe covers are ADA compliant when properly installed.

Superior in strength and durability, these thin strips insulate as well as protect personnel from accidental contact with hot pipes. Use for exhaust, hot water, and process pipes.

Lightweight and super thin, these fiber-reinforced silica aerogel sheets and strips flex into tight spaces other insulation can't. Use on process piping and in power-generating applications.

Able to withstand temperatures as low as -290° F, these super-thin, lightweight sheets are made of fiber-reinforced silica aerogel that can flex into tight spaces other insulation can't. Use in process piping and power-generating applications.

Protect insulation from light impact and moisture with this durable PVC jacketing.

Save installation time with banding that’s ready to use. It has an easy-to-close fastener on one end.

An alternative to jacketing, these coatings create a vapor barrier and protect from conditions outdoors. They are often used on irregularly shaped surfaces, such as fittings, flanges, and valves.

Spray on this clear gel to protect components and surfaces from heat damage and discoloration caused by soldering, welding, and brazing. It is nonstaining and won't leave a residue.

Lay, coat, and bond firebricks. Apply this mortar with a trowel.

This two-part expanding foam insulation meets ASTM standards for flame and smoke and covers large areas.

Cover large areas with this two-part expanding foam insulation.

A silicone rubber coating on this fiberglass sleeving protects against sparks and molten metal splash.

A specially formulated silicone rubber coating allows this sleeving to stretch over items during installation; it then tightens around its contents for a secure fit.

Use this PTFE sleeving in applications where temperatures reach up to 500° F.

With a temperature rating of 1800°F or higher, this sleeving can withstand hotter temperatures than fiberglass and most ceramic.

Unlike fiberglass and silica, this sleeving won't irritate skin, so it's easier to handle. It has a temperature rating of 1100° F or higher.

Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.

Braided from thick plastic strands, this sleeving has excellent abrasion resistance. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Tight braiding makes this sleeving resistant to fraying when cut with scissors. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Tested to meet MIL-STD-202, this sleeving meets performance standards for flame retardance. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Rated UL 2024 and NFPA 262, this sleeving is approved for use in plenum spaces such as duct work and above a drop ceiling. It self-extinguishes and emits minimal amounts of smoke and gas during combustion. Stretch to fit over items for easy installation; it tightens around its contents for a secure fit.

Made of aluminum with a fiberglass liner, this sleeving reflects heat away from contents and withstands temperatures up to 390°F. A slit along the entire length makes it easy to install around wire, cable, and hose without disconnecting them.

Zip this sleeving around wire, cable, or hose that are connected at both ends to quickly bundle them.

Wrap this sleeving around wire, cable, and hose without disconnecting them. It has a slit along the entire length and wraps over itself to stay closed without an adhesive strip or other closure.

Often used to protect wire, cable, and hose in robotics and other automated applications, this highly flexible sleeving withstands continuous motion without tearing or fraying.

Use this shielded sleeving to protect wire and cable from signal distortion caused by nearby equipment and devices. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.

Unlike traditional sleeving that bunches wire and cable into a circle, this sleeving holds them flat, so it’s good for tight spaces such as vehicle interiors. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.

The corrugated construction gives this sleeving impact and abrasion resistance similar to conduit, but with more flexibility.

A slit along the length makes this sleeving easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.

Rated UL 94 V-2, this sleeving resists combustion and minimizes the spread of flames. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. It has impact and abrasion resistance similar to conduit, with more flexibility.

A hinge along the entire length makes this one-piece sleeving easy to open for installation. Interlocking ridges overlap along the opening to protect contents from dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

Made of neoprene rubber, this sleeving has excellent abrasion resistance. It can be quickly applied to hose or cable like tape, so it's a good option for emergency patches.

This sleeving absorbs UV light, so it can be used in direct sunlight without getting damaged. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Protect cables, cords, and wire and form them into bundles in your food-processing plant while lowering the risk of contaminating the food.

Extra-thick walls provide better protection against abrasion and tears than standard moisture-seal tubing, as well as creating a water-resistant seal.

This PTFE tubing withstands temperatures up to 450° F and has an inner lining that creates a water-resistant seal when heated.

Made of woven polyolefin/polyester fabric, this tubing has excellent abrasion resistance so it can be dragged over rough surfaces without damage.

Resistant to diesel fuel, hydraulic fluid, and lubricating oil, this tubing is often used in vehicles.

Also known as halogen-free tubing, this tubing produces minimal amounts of smoke and gas if exposed to an open flame, so it can be used in enclosed areas such as ships and tunnels.

This tubing shrinks down to a quarter of its original ID, so it creates a tight seal over irregularly shaped objects. It withstands up to 500° F.

After being cleaned with alcohol, this tubing is bagged and sealed in a clean room. It's certified for material quality and purity.

Made of PVDF, this tubing has excellent cut and abrasion resistance. It has a flame-retardant additive that resists combustion and minimizes the spread of flames.

Approved for contact with food, this tubing is FDA Compliant 21 CFR 177.1330.

Identify ground wire with this green-and-yellow striped tubing.

Protect bus bars and other high-voltage devices—this tubing withstands voltages up to 5,000 volts.

Extra-thick walls provide more protection against abrasion and tears than standard high-shrink-ratio tubing. This tubing shrinks down to 1/6th of its original ID, so it creates a tight seal over irregularly shaped objects.

With thin walls, this tubing shrinks faster than other high-temperature tubing. It withstands up to 500° F.

Create a permanent seal without applying heat. This tubing is also known as cold-shrink tubing.

Organize and route wire and cable in an enclosure—this tubing bundles wires together while allowing them to reach different connection points.

Maintain a supply of tubing in a variety of sizes that withstand abrasion, moisture, and chemicals.

Seal the end of crimped connections, such as motor coils, to protect them from moisture.