For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Secure two pressurized hydraulic lines with a single clamp. Mount these clamps directly onto rails, no adhesive or welding required. They fit tightly around the lines to reduce vibration.

A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

Backed with foam adhesive tape, these clamps mount to any smooth surface—no fasteners required. They are noncorrosive, nonconductive nylon.

Flexible grooves inside these polypropylene clamps allow material to expand and contract. Clamps are moisture and chemical resistant.

Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.

Compared to metal loop clamps, plastic loop clamps reduce wear on soft materials, such as tubing and cable. Clamps are nonconductive and noncorrosive.

Tighten the bolt for an exact fit around material. Clamps secure vertical pipes in sanitation drain applications and prevent them from coming in contact with the mounting surface.

Use these clamps to route insulated pipe through floors. They have a plastic insert that creates a seal around the pipe's insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.

These hangers fit a range of material sizes. Push them closed to lock at the size you need. They provide a more secure hold on material than loop hangers.

Connect these hangers to organize multiple lines of pipe, tubing, and conduit. The tight-fitting, santoprene body reduces vibration and prevents corrosion caused by metal-to-metal contact.

Clip these hangers onto the side of threaded rod. Unlike other threaded-rod-mount hangers, you can use more than one hanger on the same rod to organize multiple lines of pipe, tubing, and conduit.

Use these hangers in corrosive environments and where chemicals are present. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.

Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.

Cut as much strap as you need to hang duct, pipe, and other materials.

A versatile solution for temporary hanging of pipe and tubing at work sites as well as anywhere welding and fastening are not possible. Feed material through the strap, then use the D-rings to adjust the hanging height.

Route bundles of wire and cable through a single hook. A wide opening allows access for installation, adjustment, and removal.

Temporarily mount routing rings and other threaded components to steel and iron surfaces.

Hang these S-hooks from fencing, railing, and wire to route large bundles of material through temporary and unfinished work areas, such as mining and construction sites, then unhook them when the job's done. A PVC coating protects material from abrasion.

These plastic rings won't conduct electricity. Also known as distribution rings, they have a large opening for routing multiple cables. A smooth surface prevents damage to wire and cable.

Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.

Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.

Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.

Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.

Suspend material at any angle from the beam. Clamps have a fixed jaw that secures to the beam and a hanger that swivels 360° to position material and accommodate for misalignment.

Support strut channel at a right angle to the beam.