How to Identify and Measure Fittings
Pipe size is an industry designation, not the actual size. View information about how to measure threaded and unthreaded pipe and pipe fittings.
More
About Metal Tubing
More
High-Pressure Nipples for Compressed Gas
Commonly used in high-pressure welding applications, these nipples connect your tank to the inlet of a pressure regulator. One side has a threaded pipe end and the other side has a rounded end that sits inside a threaded nut (sold separately) so you can make a threaded connection.
316 stainless steel nipples have excellent corrosion resistance.
For technical drawings and 3-D models, click on a part number.
- Maximum Pressure: See table
- Maximum Temperature: 120° F
Regulator Connection | ||||||
---|---|---|---|---|---|---|
For Number (Max. Pressure) | Pipe Size | Thread Type | Lg. | For Use With | Each | |
316 Stainless Steel—Tighten With Wrench | ||||||
CGA 705 (3,000 psi @ 72° F) | 1/4 | NPT | 2 1/2" | Ammonia | 000000000 | 000000 |
- Maximum Pressure: See table
- Maximum Temperature: 120° F
Number | Gender | Thread Size | Thread Type | Thread Direction | Max. Pressure | For Use With | Each | |
316 Stainless Steel | ||||||||
---|---|---|---|---|---|---|---|---|
CGA 705 | Female | 1.125"-14 | UNS | Right Hand | 3,000 psi @ 72° F | Ammonia | 000000000 | 000000 |
Nuts for High-Pressure Nipples for Compressed Gas
Slide a high-pressure hose nipple for compressed gas into one of these nuts to connect a pipe to the inlet of a pressure regulator. They are also known as CGA (Compressed Gas Association) nuts and inlet nuts.
316 stainless steel nuts have excellent corrosion resistance.
Note: Nuts have a CGA, BS, or DIN number that corresponds to a specific type of gas. Choose a nut with the same number as your tank and other system components.
For technical drawings and 3-D models, click on a part number.
- Maximum Pressure: See table
- Maximum Temperature: 120° F, except DIN 477 No. 9: 250° F
Number | Thread Size | Thread Type | Thread Direction | Max. Pressure | For Use With | Each | |
316 Stainless Steel | |||||||
---|---|---|---|---|---|---|---|
CGA 705 | 1.125"-14 | UNS | Right Hand | 3,000 psi @ 72° F | Ammonia | 000000000 | 000000 |
Stainless Steel Tubing for Corrosive Gases
- Temperature Range: -340° to 800° F
- Bending Method: Tube Bender
- Compatible Tube Fittings: Compression
A thin layer of silicon on the interior provides a smooth surface and offers protection against corrosive gases.
Seamless tubing is smoother and stronger than welded tubing and can be flared without splitting. Welded tubing is more economical than seamless tubing; it has a smoothed weld bead on the inside to reduce particle buildup.
304 stainless steel has very good corrosion resistance.
316 stainless steel offers excellent corrosion resistance.
For technical drawings and 3-D models, click on a part number.
OD | Wall Thick. | ID | Max. Pressure | Temper Rating | 1 ft. | 3 ft. | 6 ft. | |
Welded 304 Stainless Steel | ||||||||
---|---|---|---|---|---|---|---|---|
For Use With Ammonia, Nitrogen Oxide, Sulphur Oxide | ||||||||
1/8" | 0.02" | 0.085" | 3,000 psi @ 72° F | Soft | 00000000 | |||
1/4" | 0.02" | 0.21" | 2,000 psi @ 72° F | Soft | 00000000 | |||
Seamless 316 Stainless Steel | ||||||||
For Use With Ammonia, Nitrogen Oxide, Sulphur Oxide | ||||||||
1/8" | 0.035" | 0.055" | 8,500 psi @ 72° F | Soft | 00000000 | |||
1/4" | 0.035" | 0.18" | 4,300 psi @ 72° F | Soft | 00000000 |
Miniature Stainless Steel Tubing for Corrosive Gases
- Temperature Range: -340° to 800° F
- Bending Method: Tube Bender
- Compatible Tube Fittings: Compression
A thin layer of silicon on the interior provides a smooth surface and offers protection against corrosive gases. Tubing has thin walls and is made to tight tolerances for use in precision applications. It is welded with a smoothed weld bead on the inside to reduce particle buildup. It also has very good corrosion resistance. To cut this tubing, you can use abrasive cutoff wheels and deburring tools (not included).
For technical drawings and 3-D models, click on a part number.
Supplied-Air Hood Respirators for Air Pumps
When connected to an air pump, respirators provide a continuous supply of clean air. They have a chemical-resistant Tychem 2000 (formerly known as Tyvek QC) hood that protects against light liquid splashes. Tuck the hood with outer bib and inner bib into your clothing for splash protection.
Pinlock suspension hats adjust with interlocking straps. Ratchet suspensions adjust with an easy-turn knob.
Add extension hose (sold separately) to increase your span up to 300 ft. To maintain NIOSH approval, respirators must be used with the hoses listed.
Lens | |||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Use With | NIOSH Approval | Adjustment Style | Hat Size | Material | Ht. | Wd. | Required Flow Rate, cfm | Flow Rate | Hose Lg., ft. | Motor Type | Power Source | Motor Power, hp | Voltage | Plug Type | Cord Lg., ft. | Each | |
Solid Particles, Organic Vapors, Acid Gases, Ammonia, Formaldehyde, Methylamine | TC-19C-0154 | Ratchet | 6 1/2-8 | PETG Plastic | 6" | 16" | 6-15 | __ | 50 | __ | __ | __ | __ | __ | __ | 000000 | 0000000 |
Solid Particles, Organic Vapors, Acid Gases, Ammonia, Formaldehyde, Methylamine | TC-19C-0154 | Pinlock | 6 1/2-8 | Acetate Plastic | 6" | 16" | 6-15 | 10 cfm @ 5 psi | 50 | Open Dripproof | Electric | 3/4 | 115V AC | Three Prong | 8 | 0000000 | 00000000 |
Supplied-Air Full-Face Respirators for Air Pumps
The portable pump on these respirators provides a continuous supply of clean air for one person.
Add extension hose (sold separately) to increase your span up to 300 ft. To maintain NIOSH approval, respirators must be used with the hoses listed.
Lens | |||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Use With | NIOSH Approval | Size | Mask Material | Material | Ht. | Wd. | Flow Rate | Hose Lg., ft. | Max. Span, ft. | Motor Type | Power Source | Motor Power | Voltage | Plug Type | Cord Lg., ft. | Each | |
Solid Particles, Organic Vapors, Acid Gases, Ammonia, Formaldehyde, Methylamine | TC-19C-0322 | M/L | Silicone Rubber | Polycarbonate Plastic | 10" | 7" | 10 cfm @ 5 psi | 50 | 300 | Open Dripproof | Electric | 3/4 hp | 115V AC | Three Prong | 8 | 0000000 | 000000000 |
Supplied-Air Helmet Respirators for Air Pumps
Good for use around abrasive blasters and paint sprayers, these respirators are made of high-density materials that protect against rough airborne particles. An air pump (sold separately) is required. The inner lens meets ANSI/ISEA standards for impact resistance. Respirators have a pinlock suspension that adjusts with interlocking straps.
Add extension hose (sold separately) to increase your span up to 300 ft. To maintain NIOSH approval, respirators must be used with the hoses listed.
Lens | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Use With | NIOSH Approval | Hat Size | Material | Ht. | Wd. | Required Flow Rate, cfm | Hose Lg., ft. | Max. Span, ft. | Connection Type | Quick-Disconnect Shape | Coupling Size | Specifications Met | Each | |
Solid Particles, Organic Vapors, Abrasive Blasting Media, Acid Gases, Ammonia, Formaldehyde, Methylamine | TC-19C-0293 | 6 1/2-8 | Acetate Plastic | 5" | 14" | 6-15 | 100 | 300 | Quick-Disconnect Hose Coupling | Industrial | 1/2 | ANSI/ISEA Z87.1+, ANSI/ISEA Z89.1 Class C | 00000000 | 000000000 |
Optional 100-ft. Extension Hose | 0000000 | Each | 0000000 |
Replacement Outer Lens (Pkg. of 10) | 00000000 | Pkg. | 0000 |
Replacement Breathing Tube | 00000000 | Each | 000000 |
Replacement Adhesive-Backed Lens Covers (Pkg. of 10) | 00000000 | Pkg. | 0000 |
Optional 50-ft. Extension Hose | 0000000 | Each | 000000 |
3/4-hp Pump | 00000000 | Each | 00000000 |
Replacement Inner Helmet Shell and Pinlock Suspension | 00000000 | Each | 00000 |
Replacement Cape | 00000000 | Each | 000000 |
Replacement Inner Lens | 00000000 | Each | 0000 |
Supplied-Air Helmet Respirators for Plant Air Lines
Good for use around abrasive blasters and painters, these respirators are made of high-density materials that protect against rough airborne particles. The inner lens meets ANSI/ISEA standards for impact resistance.
Respirators have a pinlock suspension that adjusts with interlocking straps.
Add extra hose to span up to 300 ft. To maintain NIOSH approval, respirators must be used with the hoses listed.
Use a cooling tube (sold separately) to cool incoming air by as much as 30° F.
Lens | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Use With | NIOSH Approval | Hat Size | Material | Ht. | Wd. | Required Flow Rate, cfm | Hose Lg., ft. | Connection Type | Quick-Disconnect Shape | Coupling Size | Specifications Met | Each | |
Solid Particles, Organic Vapors, Abrasive Blasting Media, Acid Gases, Ammonia, Formaldehyde, Methylamine | TC-19C-0293 | 6 1/2-8 | Acetate Plastic | 5" | 14" | 6-15 | 25 | Quick-Disconnect Hose Coupling | Industrial | 1/4 | ANSI/ISEA Z87.1+, ANSI/ISEA Z89.1 Class C | 00000000 | 000000000 |
Replacement Outer Lens (Pkg. of 10) | 00000000 | Pkg. | 00000 |
Optional 25-ft. Extension Hose | 0000000 | Each | 000000 |
Replacement Breathing Tube | 00000000 | Each | 000000 |
Optional 50-ft. Extension Hose | 0000000 | Each | 000000 |
Replacement Cape | 00000000 | Each | 000000 |
Replacement Adhesive-Backed Lens Covers (Pkg. of 10) | 00000000 | Pkg. | 0000 |
Replacement Inner Lens | 00000000 | Each | 0000 |
Replacement Inner Helmet Shell and Pinlock Suspension | 00000000 | Each | 00000 |
Optional Cooling Tube with Temperature Control Valve | 0000000 | Each | 000000 |
Supplied-Air Hood Respirators for Plant Air Lines
Made of chemical-resistant Tychem 2000 (formerly known as Tyvek QC), these hood respirators have both an outer bib and an inner bib that tucks into your clothing for splash protection. They hook up to your plant's air lines—because you don’t need to draw air through a filter or cartridge, resistance and fatigue are minimized. Respirators have a ratchet suspension that adjusts with an easy-turn knob.
Add extension hose (sold separately) to increase your span up to 300 ft. To maintain NIOSH approval, respirators must be used with the hoses listed.
Use a cooling tube (sold separately) to cool incoming air by as much as 30° F.
Lens | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Use With | NIOSH Approval | Size | Hat Size | Material | Lens Construction | Ht. | Wd. | Required Flow Rate, cfm | Hose Lg., ft. | Connection Type | Quick-Disconnect Shape | Coupling Size | Each | |
Solid Particles, Organic Vapors, Acid Gases, Ammonia, Formaldehyde, Methylamine | TC-19C-0154 | One Size | 6 1/2-8 | PETG Plastic | Solid | 6" | 16" | 6-15 | 25 | Quick-Disconnect Hose Coupling | Industrial | 1/4 | 000000 | 0000000 |
Optional 25-ft. Extension Hose | 0000000 | Each | 0000000 |
Optional 50-ft. Extension Hose | 0000000 | Each | 000000 |
Optional Cooling Tube with Temperature Control Valve | 0000000 | Each | 000000 |
Replacement Ratchet Suspension | 0000000 | Each | 00000 |
Replacement Hood | 000000 | Each | 00000 |
Optional Adhesive-Backed Lens Covers (Pkg. of 5) | 00000000 | Pkg. | 00000 |