About twice as strong as aluminum rivet nuts, these steel rivet nuts are zinc plated for mild corrosion resistance.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

Wedges under the flange lock the nut in place in soft materials such as brass and aluminum.

These kits include one size of low-profile rivet nuts.

These low-profile rivet nuts are one-third the weight of steel and have mild corrosion resistance.

About twice as strong as aluminum rivet nuts, these rivet nuts are zinc plated for mild corrosion resistance.

These rivet nuts are mildly corrosion resistant.

A PVC coating minimizes the chance of scratching the surface of your material. These rivet nuts are more corrosion resistant than zinc-plated steel rivet nuts.

A PVC foam seal under the flange keeps liquids and gasses from leaking between the nut and the surrounding material.

Press these metric nuts into a drilled or punched hole with an arbor press or similar pressure tool.

These nuts have good chemical resistance and may be mildly magnetic.

A flat hex head sits flush against the material surface for use in low-clearance applications.

These press-fit nuts have a zinc plating for corrosion resistance in wet environments.

Also known as broach style captive nuts, these nuts have good chemical resistance and may be mildly magnetic.

These nuts can be used in channels and tight spaces where round-base weld nuts won't fit.

Weld these nuts to stainless steel surfaces.

Projections on the base concentrate the weld and provide room for heat to dissipate.

Weld these nuts to uncoated steel surfaces.

A smooth base on these metric nuts provides more contact with the mating surface than weld nuts with projections

Projections on the base concentrate the weld and provide room for heat to dissipate.

Weld these metric nuts to flat and uneven uncoated steel surfaces for a strong permanent hold.

You can weld these metric nuts to flat and uneven uncoated stainless steel surfaces for a strong permanent hold.

Threads float inside the retainer so you can install a bolt at a slight angle to align with off center parts.

These nuts have three mounting holes to accept screws and rivets for use with thin materials.

These adhesive-mount nuts have a zinc plating for corrosion resistance in wet environments.

Stainless steel nuts have excellent corrosion resistance in most environments.

Use these tube-end weld nuts with left-hand threaded fasteners.

The flange keeps these inserts from being pulled through a hole and provides a load bearing surface.

Assortments include various sizes of tapping inserts for softwood.

Made from brass, these inserts are nonmagnetic, mildly corrosion resistant, and electrically conductive.

Steel inserts have high strength for durability.

These 18-8 stainless steel tee nut inserts have better corrosion resistance than zinc-plated steel tee nut inserts.

Ridges on the barrel of these inserts make them less likely to split hardwood than inserts with prongs. They're often used in wood that has been cut across the growth rings.

Hooked prongs give these inserts excellent holding power even when removing screws.

An open end allows long screws and bolts to pass through the insert.

Mount these inserts flush or below the material's surface.

70% lighter than stainless steel, these aluminum inserts are mildly corrosion resistant and nonmagnetic.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.

The flange keeps these inserts from pulling through a hole. Press them in from the underside of material, and install a screw from the top of material.

The barbed sides keep these securely in place even before a screw is installed.

Install these inserts into plastic parts to create a secure base for fasteners.

The tapered shape makes it easier to guide these inserts into a hole during installation. Use a drill bit to create a straight hole, then taper the top half.

These inserts are the most corrosion-resistant thread-locking inserts we offer.

A black-phosphate finish provides mild corrosion resistance.

Adhesive on both the internal and external threads keeps these inserts in place and holds screws tight.

Eliminating the need for primer, these inserts are coated to resist corrosion when installed in different materials.

Made of nickel alloy, these inserts are more resistant to acids and salt water than stainless steel inserts.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

A distorted thread grips the screw to resist loosening.

A dry film keeps the screw from sticking or binding in these inserts during installation.

Kits include helical inserts, a tap, and an installation tool.

Inserts come with a through-hole tap and installation tool.

Forming the strongest hold of any of our threaded inserts, these inserts have a distorted internal thread to lock screws into place and keys that drive into surrounding material to prevent slipping and rotating.

Made of 18-8 stainless steel, these inserts have good corrosion resistance.

These inserts come with an installation tool. Drive the keys into the surrounding material for a more secure hold than thread-locking inserts.

A wide flange distributes the load over a large area. Hammer these inserts into a drilled hole.

A ribbed-shaped body holds the nut in place so it won't move when tightening a screw. Assortments contain rivet nuts, mandrels, nosepieces, and a plier-style installation tool.

Also known as insert nuts, these convert slotted holes to threaded round holes and keep them centered in the channel.

A spring plus serrated grooves that grip the lip of the channel provide a more secure hold than standard strut channel nuts.

In addition to serrated grooves for gripping the lip of the channel, these nuts have wings for easy positioning.

There's no need for additional fasteners with these nuts—they combine a strut channel nut with a spring and a threaded stud.

Insert these nuts into the long open side of strut channel and twist to secure. A built-in washer enables one-handed installation.