The flange keeps these inserts from being pulled through a hole and provides a load bearing surface.

Assortments include various sizes of tapping inserts for softwood.

These 18-8 stainless steel inserts have excellent resistance to chemicals and may be mildly magnetic.

Steel inserts have high strength for durability.

The most corrosion resistant tee nut inserts we offer, these inserts stand up to chemicals and salt water.

Fewer prongs than other tee nut inserts reduce the risk of splitting hardwood—these inserts have three short prongs.

Hooked prongs give these inserts excellent holding power even when removing screws.

An open end allows long screws and bolts to pass through the insert.

Mount these inserts flush or below the material's surface.

Made of 18-8 stainless steel, these inserts have good corrosion resistance.

These inserts are made to stringent military specifications.

These inserts come with an installation tool. Drive the keys into the surrounding material for a more secure hold than thread-locking inserts.

A black-phosphate finish provides mild corrosion resistance.

These inserts are the most corrosion-resistant thread-locking inserts we offer.

Adhesive on both the internal and external threads keeps these inserts in place and holds screws tight.

Eliminating the need for primer, these inserts are coated to resist corrosion when installed in different materials.

Made of nickel alloy, these inserts are more resistant to acids and salt water than stainless steel inserts.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

A distorted thread grips the screw to resist loosening.

Without a prong to break off and retrieve, these inserts are often used where debris could cause damage.

Kits include helical inserts, a tap, and an installation tool.

Inserts come with a through-hole tap and installation tool.

Install these inserts into plastic parts to create a secure base for fasteners.

The tapered shape makes it easier to guide these inserts into a hole during installation. Use a drill bit to create a straight hole, then taper the top half.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.

Made from brass, these inserts are electrically conductive, nonmagnetic, and have good corrosion resistance.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

The flange keeps these inserts from pulling through a hole. Press them in from the underside of material, and install a screw from the top of material.

The barbed sides keep these securely in place even before a screw is installed.

70% lighter than stainless steel, these aluminum inserts are mildly corrosion resistant and nonmagnetic.

Press these inserts into a drilled hole and the flexible metal teeth anchor them in the material. Use them with carbon fiber, fiberglass, and garolite.

The coated flange seals out moisture and prevents corrosion.

A PVC coating minimizes the chance of scratching the surface of your material. These rivet nuts are more corrosion resistant than zinc-plated steel rivet nuts.

About twice as strong as aluminum rivet nuts, these low-profile rivet nuts have a cadmium or tin-zinc plating for corrosion resistance.

These low-profile rivet nuts are one-third the weight of steel and have mild corrosion resistance.

A PVC foam seal under the flange keeps liquids and gasses from leaking between the nut and the surrounding material.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

Wedges under the flange lock the nut in place in soft materials such as brass and aluminum.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

Threads float inside the nut so you can install a screw at a slight angle to align with off-center parts. They’re also known as Riv-Float nuts.

Square weld nuts have more weld points than hex weld nuts for a stronger hold. Use them on flat surfaces.

Weld these metric nuts to flat and uneven uncoated steel surfaces for a strong permanent hold.

You can weld these nuts to flat and uneven uncoated stainless steel surfaces for a strong permanent hold.

Weld these nuts to uncoated steel surfaces.

A smooth base provides more contact with the mating surface than weld nuts with projections.

Weld these nuts to stainless steel surfaces.

Threads float inside the retainer so you can install a bolt at a slight angle to align with off center parts.

Weld these nuts to stainless steel surfaces.

A smooth base on these metric nuts provides more contact with the mating surface than weld nuts with projections

These nuts have three mounting holes to accept screws and rivets for use with thin materials.

These adhesive-mount nuts have a zinc plating for corrosion resistance in wet environments.

Also known as broach style captive nuts, these metric nuts have good chemical resistance and may be mildly magnetic.

These press-fit nuts are tin plated to resist corrosion from chemicals and salt water.

These metric nuts have good chemical resistance and may be mildly magnetic.

These press-fit nuts have a zinc plating for corrosion resistance in wet environments.

These press-fit nuts have a nylon insert that grips threads to resist loosening.

A flat hex head sits flush against the material surface for use in low-clearance applications.

Stainless steel nuts have excellent corrosion resistance in most environments.

About half the strength of medium-strength steel coupling nuts, these metric nuts are for light duty fastening applications.

For narrow holes and small cavities where toggle anchors won't fit.

The fastest way to install shallow-hole female-threaded anchors. Just push the tip of the tool into the anchor and turn the tool with a power drill.

Drive these tools with a hammer to expand anchors.

These 18-8 stainless steel anchors have good chemical resistance.

A zinc plating provides corrosion resistance in wet environments.

A zinc plating provides corrosion resistance in wet environments.

Install like a stud anchor—just thread the anchor, a nut, and a washer onto the end of a threaded rod, drive into a hole, and turn the nut to expand the base. Also known as rod anchors, they're often used with threaded rod to hang pipe and wiring.

These 316 stainless steel anchors have excellent resistance to chemicals and salt water.

A ribbed-shaped body holds the nut in place so it won't move when tightening a screw. Assortments contain rivet nuts, mandrels, nosepieces, and a plier-style installation tool.

Use these rivet nuts for light duty fastening in low-clearance applications. Assortments include rivet nuts, mandrels, and an installation tool.