Place the tip of these tools into an insert and strike them with a hammer to drive the keys into the material. They’re compatible with Keensert® inserts.

Extract heat-set inserts by attaching these tips to a soldering iron. The tips transfer heat from the soldering iron to the insert, softening the surrounding plastic to loosen the insert so it can be removed.

Place the tip of these tools into installed inserts and push down to trigger the spring-loaded punch to break off the prong.

Screw an insert onto these tools and drive them a quarter to half-turn below the material’s surface.

Use these installation bits with power drills and drill presses as an alternative to a screwdriver for fast installation.

Compatible with push-to-expand and Dodge inserts, these tools push down a plate inside the insert so the insert expands and stays secure in the surrounding material.

These installation bits can be used with power drills and drill presses as an alternative to a hex driver for fast installation.

Use these tools to install smooth and ribbed body rivet nuts. An indicator allows you to ensure your rivet nut installs correctly.

Smaller and lighter than cordless and hydraulic rivet nut tools, use these to install thin-walled bulbed, ribbed, sleeve, and smooth rivet nuts.

Install smooth body rivet nuts.

Turn these tools by hand to install low-profile rivet nuts.

A sleeve slides over the pin and holds it in place.

Use with internally threaded dowel pins.

Use these tools to drive the threaded stud into a solid surface.

Punch a hole in your material to prepare for the installation of fabric grommets. Strike these tools with a mallet.

Squeeze the adjustable handle to install standard and dual-sided fabric snaps and fabric grommets.

These punches set grommets that have a standard washer, tooth lock washer, or an extended-neck washer.

Assortments include various sizes of helical inserts and a tap, a drill bit, and an installation tool for each thread size.

Optimized for use on steel, these inserts can run at higher cutting speeds and will last longer than inserts for multiple materials.

Cut aluminum, copper, brass, and other non-ferrous materials with these premium inserts.

Heat resistant and shaped for turning stainless steel specifically, these inserts will last longer than inserts for multiple materials.

Replace clamps, screws, seats, and slotted pins in carbide insert holders.

These tools come with carbide inserts installed. When one edge of the insert dulls, rotate it to use a sharp edge.

Resisting wear and fractures when cutting hardened steel, these cubic boron nitride inserts last longer than carbide inserts.

Fit these holders directly into a lathe tool post or appropriately sized holder without the need for a tool block.

Pair these holders with a tool block for right- and left-hand mounting in a lathe.

The rounded nose on these inserts contours the outside of the workpiece and cuts grooves with rounded edges.

Pair these holders with a tool block for right- and left-hand mounting in a lathe.

These inserts can cut grooves on both the outside and inside of a workpiece depending on the holder used.

Pair these holders with a threading insert or a grooving insert to make cuts on the inside of a hollow workpiece.

These tools come with one high-speed steel insert for use on steel and stainless steel and one high-speed steel insert for use on softer materials, such as aluminum and brass. When one point of an insert dulls, rotate it to use a sharp point.

Use these tools to enlarge existing holes to precise diameters. They come with an insert installed. When one edge of the insert dulls, rotate it to use a sharp edge.

Deliver coolant through the holder to keep workpieces cool while boring tough materials, such as steel, stainless steel, and nickel-based alloys.

Contour the interior wall of a hollow workpiece when you pair a holder with a compatible insert.

Machine circular grooves onto the end of a workpiece.

Cut small grooves inside a workpiece for insertion and removal of O-rings.

An extra-long shank provides additional reach.

Solid carbide provides more rigidity than carbide-tipped tools.

The diamond tip on these tools offers superior cutting performance on nonferrous and nonmetallic materials, such as aluminum, copper, fiberglass, and plastic.

A carbide tip brazed onto a ground steel shank makes these tools less brittle than solid carbide tools.

The carbide tip brazed onto the ground steel shanks of these tools is more wear resistant than high-speed steel.

Use these tools to enlarge existing holes to precise diameters.

Insert the square shank of these tools into the slot of a boring tool holder and use them to enlarge existing holes to precise diameters.

Contour the interior wall of a hollow workpiece.

The long steel shank on these tools can reach farther inside the workpiece than standard boring tools.

These sets contain some of the smallest boring tools we offer.

Create a knurled pattern on the end of a workpiece.

Attach these tools to a manual lathe.

Insert pin-and-sleeve contacts into connectors.

Extract pin-and-sleeve contacts from connectors.

An insulated handle protects against accidental contact with live electrical circuits. These picks are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

The handle has a magnet at the end to pick up small steel objects. Use these picks to hold and position wire, springs, and other small parts.

The handles of these assorted picks have a magnet at the end to pick up small steel objects. Use to hold and position wire, springs, and other small parts.

Sets include a handle and an assortment of tips for holding and positioning wire, springs, and other small parts.

Change tips to use a different size or style pick for holding and positioning wire, springs, and other small parts.

Reach around obstructions and into tight spaces with picks that have long, angled tips. Use these tools to hold, separate, and position wire, springs, and other small parts.

Made of beryllium copper that is FM approved, these picks satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Install and position tiny springs and wires. Unlike conventional picks that have pointed tips, these are rounded to prevent damage to sensitive components.

A different tip at each end installs and positions tiny springs and wires. Unlike conventional picks that have pointed tips, these are rounded to prevent damage to sensitive components.

Replace tips when they become worn or to use a different style. The corkscrew tip twists into material to provide a firm hold while the handle provides the necessary leverage for pulling.

Pull material out of tight spots. Similar to removing a cork from a bottle, the tip twists into material to provide a firm hold while the handle provides the necessary leverage for pulling.

Shaped for removing the seals around bearings, insert the tip of these tools behind the seal and pull. The curved head provides leverage to remove stuck and stubborn material.

The assorted needle-sharp picks in these sets are similar to dental instruments and suitable for work around delicate circuits and components.

The angled tip and large handle make it easy to pry out cotter pins.

Sets include assorted tweezers with each style a different color for easy identification.

Hold small parts without the need to apply pressure. Squeeze these tweezers to open the tips and release to close them.

Lock the tips closed to use these tweezers like a clamp.

These general purpose tweezers grip a variety of objects.

Extra-long tips provide access to material in hard-to-reach areas.

A PTFE coating on the tips prevents material from sticking to these tweezers.

Hold small components such as wire, capacitors, and screws in the cylindrical tips.

Prevent buildup from electrostatic discharge (ESD) that can damage sensitive equipment. The cushioned grips drain static from your application and provide comfort and heat protection.

Extend the life of these tweezers by replacing the tips when they become worn. Tips are carbon fiber, which insulates against heat and won’t nick or scratch components.

Sets include an assortment of tweezers used to remove chips and other delicate components from circuit boards.

These assorted tweezers have tips that can be replaced when they become worn. Tips are carbon fiber, which insulates against heat and won’t nick or scratch components.

Designed for placing chips and electronic components on circuit boards, these tweezers have rectangular-shaped tips that are angled to reach over and around obstructions. They are also known as SMD (surface-mount device) tweezers.

Remove chips and other delicate components from circuit boards.