Install these inserts into plastic parts to create a secure base for fasteners.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.

These inserts are made to stringent military specifications.

These inserts come with an installation tool. Drive the keys into the surrounding material for a more secure hold than thread-locking inserts.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

Eliminating the need for primer, these inserts are coated to resist corrosion when installed in different materials.

A dry film keeps the screw from sticking or binding in these inserts during installation.

Without a prong to break off and retrieve, these inserts are often used where debris could cause damage.

A distorted thread grips the screw to resist loosening.

Assortments include various sizes of helical inserts and a tap, a drill bit, and an installation tool for each thread size.

These kits have short-, normal-, and long-reach inserts, an installation tool, and a tap.

These inserts are the most corrosion-resistant thread-locking inserts we offer.

These 18-8 stainless steel tee nut inserts have better corrosion resistance than zinc-plated steel tee nut inserts.

These metric nuts have good chemical resistance and may be mildly magnetic.

These press-fit nuts have a nylon insert that grips threads to resist loosening.

Also known as broach style captive nuts, these metric nuts have good chemical resistance and may be mildly magnetic.

The most corrosion resistant twist-resistant rivet nuts we offer, these stand up to chemicals.

Weld these nuts to stainless steel surfaces.

Weld these nuts to stainless steel surfaces.

You can weld these metric nuts to flat and uneven uncoated stainless steel surfaces for a strong permanent hold.

Stainless steel adhesive-mount nuts have excellent corrosion resistance in most environments.

Stainless steel nuts have excellent corrosion resistance in most environments.

More corrosion resistant than 18-8 stainless steel anchors, these 316 stainless steel anchors have excellent resistance to chemicals and salt water.

Used with adhesive in bricks and hollow blocks, such as cinder blocks, these mesh tubes create a stronger hold for rods and studs than other anchors.

Screw these studs into a tapped hole and use them as a pivot point, hinge, shaft, or locator pin.

18-8 stainless steel studs have good chemical resistance and may be mildly magnetic. Also known as hanger bolts, use them to hang, mount, and fasten parts to wood structures.

Turn these studs with a hex key for ease of installation.

A hollow center allows these studs to be used as an axle, a vent, or a passageway for wiring.

These include a barrel and a screw.

Angled under the head for a flush finish in countersunk holes.

Install these binding barrels and screws with a standard slotted screwdriver. They require a special tool to remove.

More corrosion resistant than 18-8 stainless steel binding barrels and screws, these have excellent resistance to chemicals and salt water.

Be prepared with ring shims in a variety of thicknesses. These shims fit around fasteners and shafts to precisely align, level, and adjust spacing.

These shims are made of layers of metal bonded with adhesive. Remove layers with a utility knife until you get the thickness you need.

Spin these shims onto screw threads to extend the shoulder length.

Adjust spacing between bearings and other components on shafts. These shims are sized to fit the outer rim of a bearing.

Precisely shaped to fit snugly on keyed shafts, these shims align, level, and space components. Because of their tight fit, they also help components rotate in unison with the shaft.

Place these shims under sharpened dies to restore their original height and extend their life.

Be prepared with slotted shims in a variety of thicknesses. The slot lets you insert, remove, and adjust the shims without disassembling your machinery.

Level dies, plates, presses, and other machine tools—this shim tape conforms to curves and uneven surfaces.

Send us a drawing, and we'll cut your custom shim.

When you can't drill a through hole, use one of these flanged receptacles to provide a permanent, blind hole for a quick-release pin.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

Also known as freeze plugs, these are commonly used to permanently seal the shallow holes left in a component during the casting process.

Give open-ended standoffs a finished look and protect them from dirt and debris.

Install these mounts with a socket head cap screw—the counterbored hole ensures the screw sits flush with or below the top of the mount.

Screw and nut sets or nuts secure brackets and other accessories to rails.

Instead of a step block, support these clamps using a screw, leveling mount, or any other threaded object.