Assortments include various sizes of inserts, a soldering iron, a ceramic insulation tube, and installation tips.

With the male threaded end on these inserts, mount components directly to plastic parts.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

These 18-8 stainless steel inserts have better corrosion resistance than aluminum inserts and may be mildly magnetic.

The barbed sides keep these securely in place even before a screw is installed.

Also known as Trisert inserts, these cut threads into plastic and have better holding power than press-fit inserts.

A black-phosphate finish provides mild corrosion resistance.

The strongest key-locking inserts we offer, these inserts are made to stringent military specifications.

These inserts come with an installation tool. Drive the keys into the surrounding material for a more secure hold than thread-locking inserts.

Made of 18-8 stainless steel, these inserts have better corrosion resistance than black-phosphate steel.

These assortments include various sizes of thread-locking inserts.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

Eliminating the need for primer, these inserts are coated to resist corrosion when installed in different materials.

These inserts have a high strength-to-weight ratio and resist acids and salt water better than nickel alloy and stainless steel inserts.

A dry film keeps the screw from sticking or binding in these inserts during installation.

Without a prong to break off and retrieve, these inserts are often used where debris could cause damage.

Inserts come with a through-hole tap and installation tool.

Large threads cut into softwood such as particleboard for a strong hold.

Made from brass, these inserts are nonmagnetic, mildly corrosion resistant, and electrically conductive.

These 18-8 stainless steel inserts have excellent resistance to chemicals and may be mildly magnetic.

These 18-8 stainless steel tee nut inserts have better corrosion resistance than zinc-plated steel tee nut inserts.

Ridges on the barrel of these inserts make them less likely to split hardwood than inserts with prongs. They're often used in wood that has been cut across the growth rings.

Six prongs around the barrel of these inserts provide a strong hold and prevent them from loosening and twisting.

An open end allows long screws and bolts to pass through the insert.

Mount these inserts flush or below the material's surface.

These nuts have good chemical resistance and may be mildly magnetic.

Also known as broach style captive nuts, these nuts have good chemical resistance and may be mildly magnetic.

These tools include everything you need to install press-fit nuts by hand.

The most corrosion resistant twist-resistant rivet nuts we offer, these stand up to chemicals.

A hex-shaped body provides the highest twist resistance of any rivet nut.

About twice as strong as aluminum rivet nuts, these low-profile rivet nuts have a cadmium or tin-zinc plating for corrosion resistance.

These low-profile rivet nuts are one-third the weight of steel and have mild corrosion resistance.

Once installed these rivet nuts have a large back flange that distributes the load across a broad area for a strong hold in plastic and composites.

A PVC foam seal under the flange keeps liquids and gasses from leaking between the nut and the surrounding material.

A nonconductive rubber coating insulates the nut from electricity, seals out moisture, and damps vibration.

Weld these nuts to stainless steel surfaces.

These nuts can be used in channels and tight spaces where round-base weld nuts won't fit.

A smooth base provides more contact with the mating surface than weld nuts with projections.

Weld these nuts to stainless steel surfaces.

Square weld nuts have more weld points than hex weld nuts for a stronger hold. Use them on flat surfaces.

Threads float inside the retainer so you can install a bolt at a slight angle to align with off center parts.

Stronger than stainless steel, these nuts are comparable in strength to Grade 9 bolts.

The fastest way to install shallow-hole female-threaded anchors. Just push the tip of the tool into the anchor and turn the tool with a power drill.

Create a strong joint in a blind hole.

These rivet nuts have a smooth body and fit in smaller holes than twist-resistant rivet nuts. Assortments include rivet nuts, mandrels, nosepieces, and a plier-style installation tool.