The tapered shape makes it easier to guide these inserts into a hole during installation. Use a drill bit to create a straight hole, then taper the top half.

With the male threaded end on these inserts, mount components directly to plastic parts.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

These 18-8 stainless steel inserts have better corrosion resistance than aluminum inserts and may be mildly magnetic.

Made of 18-8 stainless steel, these inserts have good corrosion resistance.

The strongest key-locking inserts we offer, these inserts are made to stringent military specifications.

These inserts come with an installation tool. Drive the keys into the surrounding material for a more secure hold than thread-locking inserts.

A dry film keeps the screw from sticking or binding in these inserts during installation.

Made of nickel alloy, these inserts are more resistant to acids and salt water than stainless steel inserts.

A dry film keeps the screw from sticking or binding in these inserts during installation.

Inserts come with a through-hole tap and installation tool.

A black-phosphate finish provides mild corrosion resistance.

These inserts are the most corrosion-resistant thread-locking inserts we offer.

The flange keeps these inserts from being pulled through a hole and provides a load bearing surface.

Made from brass, these inserts are nonmagnetic, mildly corrosion resistant, and electrically conductive.

Steel inserts have high strength for durability.

Press these metric nuts into a drilled or punched hole with an arbor press or similar pressure tool.

About twice as strong as aluminum rivet nuts, these steel rivet nuts are zinc plated for mild corrosion resistance.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

About twice as strong as aluminum rivet nuts, these low-profile rivet nuts have a cadmium or tin-zinc plating for corrosion resistance.

These low-profile rivet nuts are one-third the weight of steel and have mild corrosion resistance.

A PVC foam seal under the flange keeps liquids and gasses from leaking between the nut and the surrounding material.

A smooth base on these metric nuts provides more contact with the mating surface than weld nuts with projections

A smooth base provides more contact with the mating surface than weld nuts with projections.

Weld these nuts to uncoated steel surfaces.

You can weld these metric nuts to flat and uneven uncoated stainless steel surfaces for a strong permanent hold.

Threads float inside the retainer of these metric nuts so you can install a bolt at a slight angle to align with off center parts.

Stainless steel nuts have excellent corrosion resistance in most environments.

18-8 stainless steel studs have good chemical resistance.

Screw the threaded end of these metric studs into a tapped hole and use the unthreaded end as a pivot point, hinge, shaft, or locator pin.

316 stainless steel studs have excellent resistance to chemicals and salt water.

Place the tip of these tools into an insert and strike them with a hammer to drive the keys into the material. They’re compatible with Keensert® inserts.

Use these installation bits with power drills and drill presses as an alternative to a screwdriver for fast installation.

Place the tip of these tools into installed inserts and push down to trigger the spring-loaded punch to break off the prong.

Screw an insert onto these tools and drive them a quarter to half-turn below the material’s surface.

These installation bits can be used with power drills and drill presses as an alternative to a hex driver for fast installation.

Nickel-plated steel has some corrosion resistance.

Made entirely of 316 stainless steel, these metric mounts have superior corrosion resistance.

Use these metric mounts on heavy machines and equipment.

Made entirely of plastic, these mounts are resistant to oil and won't scratch your mounting surface.

Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Twist these bumpers into a threaded hole.

These bumpers withstand temperatures up to 300° F, which is twice as high as our other load rated bumpers. Use them in applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, these bumpers absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Twist them into a threaded hole.

Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Mount these bumpers on a threaded stud.

Designed to slide into T-slot tracks on machine tool tables, use these nuts to secure clamps and workpieces.

After sliding the nut into a T-slot, tighten the set screw to keep it in place.