Assortments include various sizes of inserts, a soldering iron, a ceramic insulation tube, and installation tips.

With the male threaded end on these inserts, mount components directly to plastic parts.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.

Made from brass, these inserts are nonmagnetic, corrosion resistant, and electrically conductive.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

70% lighter than stainless steel, these aluminum inserts are mildly corrosion resistant and nonmagnetic.

Push down on the inside of these inserts with an installation tool and they expand to hold firm in surrounding material.

A black-phosphate finish provides mild corrosion resistance.

With a distorted internal thread and keys on the outside, these inserts create a strong hold on both fasteners and surrounding material.

Made of 18-8 stainless steel, these inserts have better corrosion resistance than black-phosphate steel.

These assortments include various sizes of thread-locking inserts.

Adhesive on both the internal and external threads keeps these inserts in place and holds screws tight.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

Eliminating the need for primer, these inserts are coated to resist corrosion when installed in different materials.

These inserts have a high strength-to-weight ratio and resist acids and salt water better than nickel alloy and stainless steel inserts.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

Without a prong to break off and retrieve, these inserts are often used where debris could cause damage.

A distorted thread grips the screw to resist loosening.

Assortments include various sizes of helical inserts and a tap, a drill bit, and an installation tool for each thread size.

Large threads cut into softwood such as particleboard for a strong hold.

Made from brass, these inserts are nonmagnetic, mildly corrosion resistant, and electrically conductive.

These 18-8 stainless steel inserts have excellent resistance to chemicals and may be mildly magnetic.

These 18-8 stainless steel tee nut inserts have better corrosion resistance than zinc-plated steel tee nut inserts.

Ridges on the barrel of these inserts make them less likely to split hardwood than inserts with prongs. They're often used in wood that has been cut across the growth rings.

Six prongs around the barrel of these inserts provide a strong hold and prevent them from loosening and twisting.

Use where vibration is a concern—these tee nut inserts have distorted threads that lock screws in place.

A closed end seals out elements and protects the threads on these inserts from debris.

Knurls hold these inserts in hardwoods such as oak, maple, and walnut to prevent twisting.

A wide flange distributes the load over a large area. Hammer these inserts into a drilled hole.

These nuts have good chemical resistance and may be mildly magnetic.

These press-fit nuts have a nylon insert that grips threads to resist loosening.

These press-fit nuts have a zinc plating for corrosion resistance in wet environments.

These press-fit nuts are tin plated to resist corrosion from chemicals and salt water.

The most corrosion resistant twist-resistant rivet nuts we offer, these stand up to chemicals.

A hex-shaped body provides the highest twist resistance of any rivet nut.

About twice as strong as aluminum rivet nuts, these low-profile rivet nuts have a cadmium or tin-zinc plating for corrosion resistance.

The most corrosion resistant low-profile rivet nuts we offer, these stand up to chemicals.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

Once installed these rivet nuts have a large back flange that distributes the load across a broad area for a strong hold in plastic and composites.

The coated flange seals out moisture and prevents corrosion.

A PVC foam seal under the flange keeps liquids and gasses from leaking between the nut and the surrounding material.

A nonconductive rubber coating insulates the nut from electricity, seals out moisture, and damps vibration.

Weld these nuts to stainless steel surfaces.

These nuts can be used in channels and tight spaces where round-base weld nuts won't fit.

A smooth base provides more contact with the mating surface than weld nuts with projections.

Weld these nuts to stainless steel surfaces.

Square weld nuts have more weld points than hex weld nuts for a stronger hold. Use them on flat surfaces.

You can weld these nuts to flat and uneven uncoated stainless steel surfaces for a strong permanent hold.

These nuts have three mounting holes to accept screws and rivets for use with thin materials.

Stainless steel adhesive-mount nuts have excellent corrosion resistance in most environments.

Stronger than stainless steel, these nuts are comparable in strength to Grade 9 bolts.

More corrosion resistant than 18-8 stainless steel anchors, these 316 stainless steel anchors have excellent resistance to chemicals and salt water.

A zinc plating provides corrosion resistance in wet environments.

Install like a stud anchor—just thread the anchor, a nut, and a washer onto the end of a threaded rod, drive into a hole, and turn the nut to expand the base. Also known as rod anchors, they're often used with threaded rod to hang pipe and wiring.

Also known as caulk-in anchors, these stay secure when there's not much material to hold.

A pivoting toggle bar creates a strong hold.

Create a strong joint in a blind hole.

These tools come with one high-speed steel insert for use on steel and stainless steel and one high-speed steel insert for use on softer materials, such as aluminum and brass. When one point of an insert dulls, rotate it to use a sharp point.

A carbide insert comes installed on these tools.

Yellow zinc-plated steel is more corrosion resistant than nickel-plated steel.

An economical choice for applications in corrosive environments that don't require high load capacities, these mounts have a plastic base.

Made entirely of 316 stainless steel, these mounts have superior corrosion resistance.

Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance.

Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance.

Nickel-plated steel has some corrosion resistance.

An economical choice for applications in corrosive environments that don't require high load capacities, these mounts have a plastic base.

Made entirely of 316 stainless steel, these mounts are our most resistant to corrosion from chemicals, solvents, and water.

Well-suited to damp environments, these mounts have a stainless steel nut for excellent corrosion resistance.