Reduce the risk of burns from accidental contact with hot pipes under your sink. These molded, flexible pipe covers are ADA compliant when properly installed.

Typically used as duct wrap, these flexible sheets consist of polyethylene bubbles covered with aluminum polyester foil that prevent 96% of heat from radiating into or away from duct. Use on rectangular and round ductwork.

Reflect sound and block noise from traveling to other parts of your facility.

With thin walls, this tubing shrinks faster than other high-temperature tubing. It withstands up to 500° F.

Use this general purpose tubing to insulate and protect wire and cable.

This tubing creates a tight seal over irregularly shaped objects.

Identify ground wire with this green-and-yellow striped tubing.

Use this tubing where wire and cable may be exposed to chemicals, oil, and acids.

Often used to bundle batteries, capacitors, and other electronics, this tubing tightly conforms to objects, similar to shrink wrap. It has excellent resistance to chemicals, oil, and acids.

This PTFE tubing withstands temperatures up to 450° F and has an inner lining that creates a water-resistant seal when heated.

Extra-thick walls provide better protection against abrasion and tears than standard moisture-seal tubing, as well as creating a water-resistant seal.

Made of PVDF, this tubing has excellent cut and abrasion resistance. It has a flame-retardant additive that resists combustion and minimizes the spread of flames.

A flame-retardant additive makes this polyolefin tubing combustion resistant and minimizes the spread of flames.

A layer of conductive cloth protects wire and cable from signal interference caused by nearby equipment and devices.

Organize and route wire and cable in an enclosure—this tubing bundles wires together while allowing them to reach different connection points.

Seal the end of crimped connections, such as motor coils, to protect them from moisture.

Keep general purpose tubing in a variety of sizes on hand.

Protect wire and cable without disconnecting them from an assembly. For a water-resistant seal, this wrap has an adhesive lining that melts when the tubing is heated and bonds to the underlying surface.

These washers have a flat bottom and high walls to protect metal screw heads from electrical current.

As you tighten your screw, the rolled collar compresses under the head to create an insulating barrier between a screw shank and a mating surface.

Apply this liquid for a skin-tight protective coating that insulates and resists moisture, acids, and corrosion.

This polyester tape has a woven mesh edge that conducts electricity. Use it to shield cables and electronic components from EMI (electromagnetic interference).

Quickly conduct heat away from electronic components. Kapton® polyimide gives this tape excellent electrical isolation.

Low-Friction Tape Shapes Made with Teflon® PTFE.

Also known as skived tape, this low-friction tape stretches to conform to irregular surfaces.

Our most slippery tape, the slick surface allows items to glide smoothly over it.

Cover chutes, packaging lines, and slides with this tape for a slippery, nonstick surface that resists abrasion and impact.

Dissipate static and create a slick surface.

PEEK offers the best wear and abrasion resistance of our low-friction tapes. Use it for wire wraps and sliding bearing surfaces.

Use this tape to wrap and splice cables, mask components while soldering, or as a 3D printing surface.

At half the thickness of our other masking tape for electronics, this polyimide tape conforms easily to components.

Providing all-weather corrosion protection, this vinyl tape resists salt water, UV light, acids, and alkalies. Use it to wrap pipes and electrical conduit both above and below ground.

Because this film dissipates heat, it is often used for printed circuit boards and power supplies.

This film is made with virgin Teflon® PTFE resins. It can handle extreme temperatures and resists most solvents.

Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.

Package food, textiles, and other products in wet environments. This film won’t absorb or swell from water.

Apply this vinyl film directly to your window to block the view.

Keep windows from producing flying glass if they break.

Also known as build sheets, stick these sheets to your printer bed for more accurate 3D printed parts than those made on bare printer beds, masking tape, and glue.

Mount brushes by sliding them into a holder. Holders can be cut to size with a hacksaw.

This trim has a metal core for added strength and stability. Made of plastic, it's also chemical resistant. Use it to protect the edges of panels, boards, signs, and mirrors from impact.

With a slippery surface, this trim minimizes friction between parts and is often used on conveyor rails, chutes, and guides. Made of plastic, it's also chemical resistant.

This trim is suitable for use in food preparation and processing environments. It's also chemical resistant. Use it to protect the edges of panels, boards, signs, and mirrors from impact in food processing applications.

With a surface resistivity of 10 ⁵ ohms this trim safeguards equipment from static electricity by diverting electrostatic charges quickly. Made of plastic, it's also chemical resistant. Use it to protect the edges of of electronics equipment and circuit boards from impact.

With a raised bulb to absorb greater impact than standard corner guards, these guards protect walls, cabinets, and other surfaces.

The raised bulb adds cushioning to absorb more impact than other surface guards to protect walls and other flat surfaces from impact.

The guards in this system have a metal core for added strength and stability. Combine corner guards and surface guards to create a system that protects walls and equipment from impact and wear. Often used in warehouse and manufacturing areas, these systems protect against damage from carts and vehicles.

Press this optically clear film into place on windows, mirrors, and glass surfaces. When one layer gets scratched or marred, peel it away to expose a new layer.

With its reflective, mirror-like finish, this film is often used to repair or create new decorative finishes on edge trim, panels, and other flat surfaces.

Easily attach, move, and replace these magnetic wear strips on metal surfaces to minimize friction—simply press them on and peel them off as needed. Often found on conveyor systems and chutes, use these strips where friction between two parts or materials is wearing down equipment to extend equipment life.

Protect the connection point of 9V batteries with these caps.