We will reply to your message within an hour.
More
Very rigid with a 0% water absorption rate, this insulation is unaffected by corrosive environments, organic solvents, and most acids. It is typically used in chemical-processing systems and underground lines.
Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.
Add a layer of insulation to prevent electricity and heat from dissipating from wire and cable.
Use this PTFE sleeving in applications where temperatures reach up to 500° F.
Access connections more easily than with standard heat-shrink tubing. Make a small slit in this tubing to peel it away.
Use this tubing in applications where temperatures reach up to 500° F. It's often used to insulate electronic components.
With thin walls, this tubing shrinks faster than other high-temperature tubing. It withstands up to 500° F.
This tubing shrinks down to a quarter of its original ID, so it creates a tight seal over irregularly shaped objects. It withstands up to 500° F.
Made of PVC, this tubing resists chemicals, oil, and solvents. The adhesive lining creates a water-resistant seal when heated.
This PTFE tubing withstands temperatures up to 450° F and has an inner lining that creates a water-resistant seal when heated.
With excellent resistance to tears and cuts, this tubing withstands demanding use.
Use this tubing where wire and cable may be exposed to chemicals, oil, and acids.
Often used to bundle batteries, capacitors, and other electronics, this tubing tightly conforms to objects, similar to shrink wrap. It has excellent resistance to chemicals, oil, and acids.
Resistant to diesel fuel, hydraulic fluid, and lubricating oil, this tubing is often used in vehicles.
Made of PVDF, this tubing has excellent cut and abrasion resistance. It has a flame-retardant additive that resists combustion and minimizes the spread of flames.
Often used in automated applications such as robotics, this highly flexible silicone rubber tubing withstands continuous motion without cracking and tearing. It resists abrasion and can be dragged over rough surfaces without damage.
Maintain a supply of tubing in a variety of sizes that withstand abrasion, moisture, and chemicals.
Create a permanent seal without applying heat. This tubing is also known as cold-shrink tubing.
Alumina ceramics withstand higher temperatures than any other ceramic and are highly chemical resistant. Powder is often used in casting processes. Add it to slurries to create custom parts and tools such as crucibles, cutting tools, and laboratory ware.
Highly pure, this green silicon carbide powder is consistent between batches and bonds better than less pure powders, yielding less cracking and wear in finished products.
This film is made with virgin Teflon® PTFE resins. It can handle extreme temperatures and resists most solvents.
Known for its naturally slippery surface, PTFE surpasses most plastics when it comes to chemical resistance and performance in extreme temperatures.
Made with Teflon® PTFE resins, these sheets and bars surpass most plastics when it comes to chemical resistance and performance in extreme temperatures.
Often used in assemblies that rub against each other, this powder blends into plastic, rubber, composites, and lubricants to keep them from sticking.
Also called reprocessed and mechanical-grade PTFE, this material is an economical alternative to standard PTFE.
Protect sensitive equipment from damaging electrical static charges.
Manufactured from Rulon PTFE, a PTFE that's modified with filler material for a super-slippery, impact-resistant surface that resists wear.
Kapton® polyimide film is an excellent electrical insulator.
This film conducts electricity to prevent the buildup of static charges.
Because this film dissipates heat, it is often used for printed circuit boards and power supplies.
Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.
A glass filler is added to this this PEEK material to offer increased durability over standard PEEK in high-stress structural applications.
Use PFA in place of PTFE and FEP for durability in repetitive processes, such as pump parts. It is chemical resistant across a wide temperature range.
Offering excellent resistance to shock, PPSU is frequently fabricated into vehicle parts and machine components that are subject to vibration. It withstands higher temperatures than polysulfone and can handle repeated autoclaving cycles.
Often used as gaskets and bearings, this slippery-surface material absorbs virtually no moisture. PCTFE is equivalent to Kel-F and Neoflon.
When excellent chemical resistance is combined with an ability to hold tight tolerances, the result is PPS—a material that’s widely machined into parts for chemical-processing applications. It is comparable to Techtron and Ryton.
Stronger than PTFE, PVDF offers good chemical resistance. Comparable to Kynar and Solef, it’s widely used for pump parts, tank liners, and seals.
In addition to a low-friction surface that prevents sticking and binding, this tough material is impact and wear resistant to handle the scuffs, scrapes, and strikes that other plastics can’t.
The addition of glass fibers makes this material more abrasion resistant than standard UHMW. It’s also known as Tivar 88.
Also known as Tivar H.O.T., this material lasts up to 10 times longer in high-temperature applications than standard UHMW.
If a chip of this material breaks off, it can be located by metal detectors to reduce contamination risks.
Practically nonabsorbent, HDPE won't swell when exposed to moisture. It is denser and more rigid than LDPE, plus it's more chemical resistant.
This nylon stays lubricated over time because it’s filled with oil. Use it to fabricate parts for hard-to-reach places where adding lubricants would be difficult.
Use these cast nylon 6 rods to make sheaves, bushings, and pulleys. All withstand higher temperatures and are easier to machine than standard nylon 6/6 rods.
This cast nylon 6 material is easier to machine than other types of nylon. It’s comparable to Nylatron and Nycast.
A good choice for making sprockets and pulleys, these cast nylon 6 tubes withstand higher temperatures and are easier to machine than standard nylon 6/6 tubes.
The addition of MDS results in a nylon with exceptional wear resistance as well as self-lubricating properties.
Often used to make gears and wear strips, these cast nylon 6 sheets and bars withstand higher temperatures and are easier to machine than standard nylon 6/6 sheets and bars.
Use Noryl PPO for electrical insulating applications where moisture is a concern. It remains dimensionally stable over time, even when temperatures fluctuate.
Because PVC resists many acids and alkalies, it’s widely used for tanks and in chemical-processing applications. Also known as PVC Type 1.
Offering greater impact resistance than standard PVC Type 1 with similar chemical resistance, this PVC Type 2 is widely used for parts that are subject to shock.
CPVC is just as chemical resistant as standard PVC Type 1 and can handle hotter temperatures up to 200° F.
This film is often used as a separator when heating parts in an oven.
Polyester resists swelling in wet environments.
These black polyester sheets protect from UV rays better than off-white polyester. Strong and semi-rigid, they won't swell in moist environments, so they're often made into pump components and spacers.
These black polyester rods protect from UV rays better than off-white polyester. Strong and semi-rigid, they won't swell in moist environments, so they're often made into valves, pump components, and spacers.
Known for its electrical insulating properties, this polystyrene is often used for cable connectors, electrical housings, and in microwave applications. It is also known as Rexolite.
A satin texture on one side of these PETG sheets makes them semiclear. You can see light from the other side, but not detailed shapes. They are more resistant to scratching and glare than standard PETG.
This polycarbonate has a static-dissipative coating that prevents electrostatic discharge from damaging sensitive electronic equipment.
PETG can be formed into complex shapes without sacrificing durability.
The slippery surface on this FEP film prevents sticking. Use it as a release film when making molded parts.
Stronger and more chemical resistant than FEP and PFA film, ETFE film resists cracking over time.
Because PVC resists acids and alkalies, it is often used in tanks and chemical-processing applications where visibility is essential.
Carbon mesh is embedded into this clear PVC film to dissipate electrostatic discharge and protect sensitive electronic equipment.
Absorbing impact without cracking or breaking, these plastic pellets are molded into parts that endure bumps, scrapes, and falls.
With a low coefficient of friction, these pellets won't wear away from abrasion that’s often caused by contact with moving parts. Melt and mold them into desired shapes.