We will reply to your message within an hour.
More
Approved for contact with food, this tubing is FDA Compliant 21 CFR 177.1330.
This film is made with virgin Teflon® PTFE resins. It can handle extreme temperatures and resists most solvents.
Known for its naturally slippery surface, PTFE surpasses most plastics when it comes to chemical resistance and performance in extreme temperatures.
Made with Teflon® PTFE resins, these sheets and bars surpass most plastics when it comes to chemical resistance and performance in extreme temperatures.
Manufactured from Rulon PTFE, a PTFE that's modified with filler material for a super-slippery, impact-resistant surface that resists wear.
Often used for circuit-breaker housings, manifolds, and semiconductor components, Ultem PEI offers excellent electrical-insulating properties.
Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.
Widely used to make parts that require autoclaving, polysulfone is a hard, rigid material that’s easy to machine and thermoform. It maintains its physical properties when heated, even when exposed to steam.
Offering excellent resistance to shock, PPSU is frequently fabricated into vehicle parts and machine components that are subject to vibration. It withstands higher temperatures than polysulfone and can handle repeated autoclaving cycles.
Often used as gaskets and bearings, this slippery-surface material absorbs virtually no moisture. PCTFE is equivalent to Kel-F and Neoflon.
When excellent chemical resistance is combined with an ability to hold tight tolerances, the result is PPS—a material that’s widely machined into parts for chemical-processing applications. It is comparable to Techtron and Ryton.
Stronger than PTFE, PVDF offers good chemical resistance. Comparable to Kynar and Solef, it’s widely used for pump parts, tank liners, and seals.
In addition to a low-friction surface that prevents sticking and binding, this tough material is impact and wear resistant to handle the scuffs, scrapes, and strikes that other plastics can’t.
Also known as Tivar H.O.T., this material lasts up to 10 times longer in high-temperature applications than standard UHMW.
This oil-filled material is self-lubricating for an extra-slippery surface.
If a chip of this material breaks off, it can be located by metal detectors to reduce contamination risks.
Delrin® acetal resin, also known as acetal homopolymer, is stronger and stiffer than acetal copolymer.
The addition of PTFE provides a more slippery, wear-resistant surface than standard Delrin® acetal resin. It’s commonly fabricated into pump components, gears, and bearings.
An economical alternative to Delrin® acetal resin, this acetal copolymer offers similar wear resistance.
Because this polypropylene resists swelling when exposed to water, it’s often fabricated into containers and parts for laboratory equipment.
Practically nonabsorbent, HDPE won't swell when exposed to moisture. It is denser and more rigid than LDPE, plus it's more chemical resistant.
These black polyester rods protect from UV rays better than off-white polyester. Strong and semi-rigid, they won't swell in moist environments, so they're often made into valves, pump components, and spacers.
These black polyester sheets protect from UV rays better than off-white polyester. Strong and semi-rigid, they won't swell in moist environments, so they're often made into pump components and spacers.
Polyester resists swelling in wet environments.
Also known as nylon 6/6, this general purpose material is often used for bearings, gears, valve seats, and other high-wear parts.
This cast nylon 6 material is easier to machine than other types of nylon. It’s comparable to Nylatron and Nycast.
Polycarbonate maintains good impact resistance across a wide temperature range. It's comparable to Lexan, Hyzod, Tuffak, and Makrolon.
The addition of glass fibers to this polycarbonate increases tensile strength for use in structural applications.
Because ABS maintains its toughness even after thermoforming, it’s often made into storage cases, tote trays, equipment housings, and protective gear.
Known for its electrical insulating properties, this polystyrene is often used for cable connectors, electrical housings, and in microwave applications. It is also known as Rexolite.
Often fabricated into signs, packaging, and light duty housings, polystyrene is easy to thermoform.
A satin texture on one side of these PETG sheets makes them semiclear. You can see light from the other side, but not detailed shapes. They are more resistant to scratching and glare than standard PETG.
Cast acrylic is easier to machine than extruded acrylic. It's comparable to Lucite and Plexiglas® Acrylic.
At only half the weight of glass, polycarbonate maintains excellent impact resistance across a wide temperature range. It's comparable to Lexan, Hyzod, Tuffak, and Makrolon.
PETG can be formed into complex shapes without sacrificing durability.
Because PVC resists acids and alkalies, it is often used in tanks and chemical-processing applications where visibility is essential.
Absorbing impact without cracking or breaking, these plastic pellets are molded into parts that endure bumps, scrapes, and falls.