A swivel caster lets you reposition your load.

Wrench-adjustable jacks require less clearance to turn than bar-adjustable jacks.

These jacks can be used to lift, spread, push, pull, and clamp.

Pump the handle by hand to raise the jack. Turn the release valve to lower the load.

These jacks have a short body to fit in low-clearance spaces. The handle pumps from side to side, requiring less vertical space than other bottle jacks.

Jacks include a ram, a hand pump with hydraulic oil, a pressure gauge, and a hydraulic hose.

Push or pry apart material with these rams by attaching them to a hydraulic pump.

Connect a hose to a ram or pump.

Connect up to four rams and a gauge to a pump. Ram connections have flow-adjustment valves to adjust ram speed, or shut it off to temporarily hold a load.

This steel-reinforced hose has male threads.

Monitor hydraulic oil pressure levels to guard against overload. These gauges are liquid filled to reduce needle vibration and include an adapter to mount the gauge in line with the hose.

Fit these compact jacks under low-height loads.

As versatile as bottle jacks, but with two lifting points—a toe for lifting loads low to the ground, and a saddle for a higher, more stable lifting point.

Roll from job to job and under hard-to-reach places.

An extra-long, reinforced tabletop gives you plenty of room for oversized loads.

The top extends beyond the base for easier access to tight spaces and bench tops.

The hand crank on these tables has two speeds for fast and slow adjustment.

An electric motor and a hydraulic pump lift loads with the push of a button.

The tabletop can go as low as 3", making loading and unloading from the floor and pallets easier.

The turntable rotates to reduce reaching.

Choose your table based on capacity, then choose the type of control that best suit your application.

A hydraulic pump and an air-driven motor do the work for you.

The screw adjustment allows you to make small changes to the height of your load.

With no legs in front, these cranes let you lift close to your load. They are also known as engine cranes, and have a hydraulic hand pump that raises and lowers the arm (boom) to lift items without the need for a hoist.

Use one to three springs (included) to automatically keep pallets at a convenient height.

The mounting plate provides a flat surface for supporting loads.

Attach these fittings to the end of a screw jack to create pivoting connections with clevis rod ends and other linkages.

Add a flat mounting surface to a ball screw jack to support loads.

Isolate vibration and absorb shock from moving equipment, even with changing loads. Also for leveling and lifting, use compressed air to adjust air springs to the height and force required for your application.

Connect audio equipment. These connectors mount to panels of any thickness, as long as you drill a mounting hole first.

The snap-on wire connection pierces the insulation to eliminate the need for wire stripping.

Install these connectors in a panel cutout to create a port for transferring data.

Use an Ethernet cable crimper to terminate these plugs.

Pull wires all the way through the connector face, and then use the crimper to cut and crimp wires in one step.

Instead of tossing Ethernet cords with a broken locking tab on their RJ45 plug, fix them with these clips.

Add ix Industrial connections to printed circuit boards (PCBs).

Lock Ethernet cords in place to prevent unauthorized removal from ports.

Push these connectors together for secure Ethernet connections that are quick and easy to connect and disconnect with just one hand. You’ll know when the plug and socket are locked in place when you hear a click.

Audio/video HDMI connectors and cords are rated IP67 when mated.

These D- and X-coded M12 connectors are desgined for high-speed Ethernet cable in damp environments.

Create various data connector configurations by snapping these adapters into the ports of keystone wall plates.

Join two Ethernet cords—these adapters have an RJ45 female connection on both ends.

Bring USB connections closer to where you need them.

Extend the reach of USB devices.

Extend audio connections by plugging a cord into each end of these adapters. Drill mounting holes to install them directly into panel cutouts.

Screw these connectors together for a more secure connection than push-in connectors.

These connectors withstand corrosion, abrasion, and welding slag. Screw them together for a secure connection. They're often used with 12 mm proximity switches, valves, and power supply units.

Plug these connectors into hazardous location devices. Using a NAMUR signal, they operate at a low current and voltage, so they prevent the risk of sparks and ignition in volatile areas.

Quickly mate these connectors by pushing them together. They're often used with 12 mm proximity switches and valves in automated systems.

Join M8 connections to M12 connections.

Push these connectors together to quickly create signal and data connections in tight spaces. All are smaller than M5 and M8 connectors. They also need less space to mate than screw-together connectors, which require two hands to twist them in place.

Reduce the number of cords needed to send and receive signals where space is tight—these splitters have an M8 plug and two M8 sockets, which are smaller than M12 plugs and sockets.

Reduce the number of electrical connections in sanitary areas, such as food plants—these connectors combine Ethernet, a power cable, and wire for signals into a single connection point.

Play audio from one source on two different speakers.

The shielding blocks signal interference from nearby equipment and devices.

The plugs on these cords pivot up to 90° in each direction to fit Ethernet jacks at awkward angles or in tight spots, such as behind equipment or in enclosures.

Connect sensors, switches, I/O modules, and computers in tight spaces.

Often used in automated applications such as robotics, these cords withstand continuous motion without degrading data transmission. They have an RJ45 plug on each end.

Securely connect equipment in data or signal applications. These cords have A- or B-coded plugs to meet the needs of your device.

Often used in assembly line networks and Fieldbus connections, these cords have B-coded M12 connections.

Send DC power to multiple electronics from one source. With industry standard barrel-style connections, these splitters are compatible with many power supplies and other devices.

Often used with 12 mm proximity switches, console lights, and valves.

FDA compliant for direct contact with food, these cords are good for use in food, beverage, and pharmaceutical plants.

These cords have an M8 connector on one end and an M12 connector on the other.

These cords have a Nano M8 connector (also known as a pico connector) on one end and an USB Type-A connector on the other.

Connect multiple M8 and M12 cords to create a network between equipment. These blocks are often used to send signal and power to proximity switches and sensors.

Place stand on a work surface to position pipe perpendicular and parallel to the frame.

Rollers support and help guide material into machinery.

Choose from mounts that support 3,000 to 110,000 lbs. for heavy machinery.

Sectional or telescoping masts on these trucks allow you to lift loads higher than standard lift trucks. Crank the handle to raise and lower loads.

A hydraulic pump powered by a rechargeable battery raises and lowers the load with the push of a button.