McMaster-Carr logo
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    9 Products

    Thin-Profile Hex Nuts

    About half the height of standard-profile nuts, these fit in spaces with low clearance. You can also use them as jam nuts by threading them against another hex nut to hold it in place.
    Medium-Strength Steel
    Image of Product. Front orientation. Hex Nuts. Thin-Profile Hex Nuts.
    These Grade 5 or Class 04 nuts are your go-to for fastening most machinery and equipment. To avoid stripped threads during installation, make sure your screw has a comparable strength rating.
    Zinc-Plated Steel—A step up from plain steel, the zinc plating withstands occasional exposure to moisture.
    Steel—Best for dry environments since moisture will cause these nuts to rust.
    Thread Size
    Wd.,
    mm
    Ht.,
    mm
    Fastener Strength
    Grade/Class
    Specs. Met
    Pkg.
    Qty.
    Pkg.
    Zinc-Plated Steel
    M42 × 4.5 mm6521ISO Class 04
    		DIN 439B, ISO 40351000000000000000
     
    Steel
    M42 × 1.5 mm6516—DIN 936100000000000000
    M42 × 3 mm6516—DIN 936100000000000000
    M42 × 3 mm6521ISO Class 04
    		DIN 439B, ISO 4035100000000000000
    M42 × 4.5 mm6516—DIN 936100000000000000
     
    Corrosion-Resistant Stainless Steel
    Image of Product. Front orientation. Hex Nuts. Thin-Profile Hex Nuts.
    18-8 Stainless Steel—The choice for wet and outdoor environments, these nuts resist rust. However, they won't hold up to the harsh chemicals that 316 stainless steel can.
    Thread Size
    Wd.,
    mm
    Ht.,
    mm
    Specs.
    Met
    Pkg.
    Qty.
    Pkg.
    18-8 Stainless Steel
    M42 × 4.5 mm6516DIN 9361000000000000000
     

    Bearing Nuts

    Image of Product. Front orientation. Bearing Nuts. Bearing Nuts, Carbon Steel, Stepped Face.

    Carbon Steel

    Stepped Face

    Often paired with spring lock washers to strengthen their hold, these bearing nuts—also known as shaft nuts—keep vibration from shifting bearings, bushings, pulleys, and gears on your threaded shaft or spindle. They have slotted sides, so you can tighten and loosen them with a spanner wrench or spanner socket.
    Carbon Steel—Carbon steel bearing nuts are strong and resist wear.
    Stepped Face—Use stepped-face bearing nuts with DIN 462 spring lock washers. You can also use them in pairs or with other bearing nuts. For the nut closer to the bearing, position the stepped face towards the bearing. All meet DIN standards for bearing lockout dimensions.
    Thread Spacing—When choosing your thread spacing, consider the precision of your application. The finer the threads, the more control you have when making adjustments.
    Nuts
    Bearing
    Lock Washers
    Thread
    Size
    Spacing
    OD,
    mm
    Wd.,
    mm
    Specs.
    Met
    For Lock Washer
    Specs. Met
    Each
    Each
    Carbon Steel
     
    Stepped Face
    M42 × 1.5 mmExtra Fine
    		6212DIN 1804DIN 462000000000000000000000000000
     

    Thin-Profile Bearing Nuts

    Image of System. Front orientation. Contains Annotated. Bearing Nuts. Thin-Profile Bearing Nuts.
    Image of Product. Front orientation. Bearing Nuts. Thin-Profile Bearing Nuts.
    Used in pairs or with another bearing nut, these thin-profile nuts—often called shaft nuts—hold bearings, bushings, pulleys, and gears in place on your threaded shaft or spindle. Threading two nuts tightly against each other makes it harder for vibration to loosen your assembly than if you used only one nut. For the nut closer to the bearing, position the stepped face towards the bearing. These thin-profile nuts have holes on the side, so you can tighten and loosen them with a pin spanner wrench. All meet DIN 1816, an international standard for bearing locknut dimensions.
    Carbon Steel—Carbon steel bearing nuts are strong and resist wear.
    Thread Spacing—When choosing your thread spacing, consider the precision of your application. The finer the threads, the more control you have when making adjustments.
    Thread
    Size
    Spacing
    OD,
    mm
    Wd.,
    mm
    Specs.
    Met
    Each
    Carbon Steel
     
    Stepped Face
    M42 × 1.5 mmExtra Fine
    		6212DIN 18160000000000000
     
    back to top