Mount these clamps to a bench top or other surface to keep workpieces in place.

Push the lever to lock the handle and prevent accidental opening.

Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.

Reduce the chance of getting pinched when unclamping. These clamps have more space between the handle and the arm than other low-profile toggle clamps.

Push the lever to lock the handle and prevent accidental opening.

Often used when assembling small parts, these small clamps have the holding strength of a full-size clamp.

Weld these clamps to the side of an object or drill your own holes in the mounting plate and bolt into place.

Two sets of mounting holes allow mounting on the bottom or side.

The mounting base secures these clamps to a rail or bar.

Suitable for production applications, these clamps have double the service life of other air-powered toggle clamps.

These clamps have mounting holes on the bottom.

The base fits into round or square holes on most workholding tables for clamping anywhere on the work surface.

Push or pull the plunger to hold your workpiece from the side.

Smaller than standard push toggle clamps, these are often used for electronics and small fixturing applications.

Pull the handle backward to push the plunger forward. These clamps secure when the plunger is fully extended to hold your workpiece from the side.

Hold workpieces of different thicknesses without adjustment.

Moving parts are sealed to prevent dirt and dust from clogging the clamp.

Panel mount through a hole with the included nut, or drill and tap a hole to flush mount. A pushing or pulling motion holds workpieces from the side.

The plunger can be locked at any position along its travel.

Fit the draw arm over a latch plate and pull the handle to clamp.

Push the lever to lock the handle and prevent accidental opening.

Eliminating the need for step blocks or other rear support, the pivoting rocker clamps workpieces of various thicknesses.

Use with T-slot nuts or bolts and a support to secure a workpiece, vise, or fixture to a machine table.

Get everything needed for basic workholding on a machine table.

Making minimal contact with the workpiece while holding securely, these clamps are good for small parts and can clamp into holes and notches.

Position these clamps between two workpieces, vises, or fixtures and secure both to your machine table using T-slot nuts or bolts.

Keep setup clamps from falling out of position when they are unclamped—the spring holds them up for quick workpiece insertion and removal. Also known as spring lifters.

A plastic pad on the gripping surface of these clamps prevents workpiece marring, making them useful for holding polished surfaces and reducing the need for secondary finishing steps.

The built-in T-slot nut on these side clamps lets you clamp a part to a machine table quickly. Their small footprint leaves more free space on your table than standard side clamps.

An alternative to setup clamps, these heavy duty clamps have high holding power to secure workpieces during machining.

The spring-loaded tips on these clamps swivel in all directions to make maximum contact with angled and uneven workpieces.

Hold a workpiece securely from the side with minimal contact, leaving more of the workpiece free for machining.

Machine these clamps to match the contours of your workpiece and turn the screw to grip.

Install these clamps into a slot in your fixture to grip at the bottom of a workpiece edge, giving the cutting tool maximum access.

Machine these fixture clamps to match the contours of your workpieces for a stronger grip. Place the clamp between the two workpieces in a fixture and tighten the screw to extend the sides of the clamp, creating a secure hold against both workpieces.

Mount using the holes in the base.

Use the power of hydraulic fluid to quickly, consistently, and repeatedly clamp and release parts with a greater clamping force than air-powered hold-down fixture clamps.

Build these components into fixture plates, machine subplates, and tombstones for quick changes. The system clamps and locates at the same time for accurate positioning with repeatability of ±0.0005".

A removable, heavy duty steel base plate provides a flat, durable clamping surface. Carry it where needed or mount the base plate to your workbench.

With five times the capacity of standard corner clamps, these secure two workpieces at a 90° angle.

Clamp up to three workpieces at 90° angles.

Position workpieces at any angle from 0° to 180°.

Use the switch to engage and disengage the magnet for easy placement and removal of your workpiece.

Sized for small parts and tight spaces, these clamps have a pivoting pad at each end to hold workpieces at any angle up to 180°.

Hold and align up to three workpieces at 90° angles.