Push or pull the plunger to hold your workpiece from the side.

Secure your workpiece from the side by fully extending the plunger, and push a lever to lock the handle in place.

Moving parts are protected by a metal cover when the clamp is engaged to prevent dirt and dust from clogging the clamp.

Pull the handle backward to push the plunger forward. These clamps secure when the plunger is fully extended to hold your workpiece from the side.

The handle can be rotated 125° for easier access or extra clearance above the clamp.

Push the lever to lock the handle and prevent accidental opening.

Drill a hole to mount these clamps through a surface and secure the mounting flange with screws. The plunger can be locked at any position along its travel.

Hold workpieces at a 90° angle.

Position workpieces at any angle from 0° to 180°.

The handle locks in a horizontal position for more clearance above the clamp than standard hold-down toggle clamps.

Push the lever to lock the handle and prevent accidental opening.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

A nonreflective black oxide finish prevents glare that can interfere with machine vision systems.

Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.

Push the lever to lock the handle and prevent accidental opening.

Weld these clamps to the side of an object or drill your own holes in the mounting plate and bolt into place.

Two sets of mounting holes allow mounting on the bottom or side.

The mounting base secures these clamps to a rail or bar.

Attach one of these nonmarring rubber or plastic tips to prevent a metal holding screw from damaging workpiece surfaces.

The base fits into round or square holes on most workholding tables for clamping anywhere on the work surface.

Eliminating the need for step blocks or other rear support, the pivoting rocker clamps workpieces of various thicknesses.

Instead of a step block, support these clamps using a screw, leveling mount, or any other threaded object.

Good for occasional machining, economy kits contain lower-strength components than standard kits.

A plastic pad on the gripping surface of these clamps prevents workpiece marring, making them useful for holding polished surfaces and reducing the need for secondary finishing steps.

Position these clamps between two workpieces, vises, or fixtures and secure both to your machine table using T-slot nuts or bolts.

Unlike other setup clamps that grip the horizontal surface of a workpiece, these clamps have a pivoting ball in the tip to get a firm hold on angled parts.

Keep setup clamps from falling out of position when they are unclamped—the spring holds them up for quick workpiece insertion and removal. Also known as spring lifters.

The built-in T-slot nut on these side clamps lets you clamp a part to a machine table quickly. Their small footprint leaves more free space on your table than standard side clamps.

Use these clamps to hold large round parts for machining. Each clamp comes with five lengths of chain that combine to accommodate different size workpieces.

Each arm has a handle for turning the magnets on and off.

Sized for small parts and tight spaces, these clamps have a pivoting pad at each end to hold workpieces at any angle up to 180°.

Switch the magnets on these clamps on and off for easy placement and removal of your workpiece.

The spring-loaded tips on these clamps swivel in all directions to make maximum contact with angled and uneven workpieces.

Hold a workpiece securely from the side with minimal contact, leaving more of the workpiece free for machining.

Machine these clamps to match the contours of your workpiece and turn the screw to grip.

Machine these fixture clamps to match the contours of your workpieces for a stronger grip. Place the clamp between the two workpieces in a fixture and tighten the screw to extend the sides of the clamp, creating a secure hold against both workpieces.

Machine these fixture clamps to match the contours of your workpiece for a stronger grip.

Mount using the holes in the base.

These clamps wedge against the workpiece ID to grip cast, unfinished, or uneven parts, leaving the outside clear for machining.

A removable, heavy duty steel base plate provides a flat, durable clamping surface. Carry it where needed or mount the base plate to your workbench.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Fit the draw arm over a latch plate and pull the handle to clamp.

As the face of these plungers is pushed in, the internal spring applies outward pressure to hold a workpiece in position against stops and rails.

Threading makes these guide pins easier to remove and replace than press fit, so they're useful for high-wear applications.

Use these tools for easier guide pin installation.

Thread in a screw, handle, or other part to create the right size and shape guide pin for your application.

Mount through the counterbored hole with a socket head cap screw to support and position workpieces and fixtures from the bottom or side.

Support rounded or irregularly shaped workpieces from the bottom or side with minimal contact.

Maintain consistent alignment in mating parts by installing a pin in one part and a liner in the other.

The shoulder provides a consistent height reference point and keeps the pin from being pressed through the fixture.

Encase these pins while molding plastic or composite parts. Once set, the knurls resist movement, letting you align the workpiece with precision on a plate or table.

Use the handle on these retractors to extend and retract a locating pin, protecting the pin from damage in applications where fixtures move through a process, such as along a conveyor belt.

Precisely align drilled holes in two parts.

The head on these pins slides side-to-side in one direction. Use one of these pins and one standard round-head pin to prevent jamming when loading and unloading workpieces with inconsistent hole spacing.

Adjust the horizontal screw to hold workpieces of varying sizes in precise positions.

When working with large or flexible workpieces that could bow under machining pressure, use these screws as easy-to-install support points. Also known as jack screws or jig screws.

For locating the side of a workpiece without milling a permanent slot into your fixture, screw these easily repositioned rails into threaded holes.

Drill precise holes without building a fixture. Clamp the jig onto your material and lift and turn the turret to select the hole size you need.

Build fixtures on multiple sides of these squares.

Ensure accurate right angles and hold workpieces and fixtures perpendicular to a machine table by securing them to these plates with clamps.

The handle extends the full length and height of these plates for use on any of their six sides.

Turn the handle to switch the magnet on and secure steel parts—no need for clamps or screws.

Precision ground to the tightest parallel tolerance, these steel plates have threaded and unthreaded holes in a grid pattern to support precise positioning and repeatability when machining.

Add components such as clamps, brackets, stops, rests, mounting plates, fixturing squares, risers, and V-blocks to build fixtures for welding and assembly.

Mount workpiece holders, light machinery, collaborative robots, and other components onto these tables to create custom workspaces, no drilling or tapping required.

Insert a plasma or oxyacetylene torch in these guides for balance and stability when cutting straight, circular, and irregular shapes. They’re designed to cut as well as bevel at the same time.

Retract the nose by pulling the knob.

Quickly align, join, or hold machine components in place in food, pharmaceutical, and other sanitary environments. Pulling the plunger knob and twisting it 90° will lock the nose into its retracted position.

Install by hand or with a hex key in low-clearance applications.

The ring allows you to attach these spring plungers to a lanyard.

An L-handle takes up less space than a T-handle.

A quarter turn of the handle locks these plungers in the retracted position. The T-handle is easy to grip.

A quarter turn of the handle locks these plungers in the retracted position. The smooth ball handle is easy to grip and won't catch on other parts.

Lock the nose into the retracted position by pulling the knob and rotating it 90°.

Press these catches into a hole.

Install with a hex key for more torque than slotted ball-nose spring plungers.