Connect Wilkerson modular filter/regulator/lubricator components with the same series number.

Smaller than standard push/pull toggle clamps, these are often used for electronics and small fixturing applications.

Pull the handle backward to push the plunger forward. These clamps secure when the plunger is fully extended to hold your workpiece from the side.

Secure your workpiece from the side by fully extending the plunger, and push a lever to lock the handle in place.

Moving parts are protected by a metal cover when the clamp is engaged to prevent dirt and dust from clogging the clamp.

Panel mount through a hole with the included nut, or drill and tap a hole to flush mount. A pushing or pulling motion holds workpieces from the side.

Hold workpieces at a 90° angle.

Grip all four corners of a rectangular workpiece.

Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.

The handle locks in a horizontal position for more clearance above the clamp than standard hold-down toggle clamps.

Push the lever to lock the handle and prevent accidental opening.

Often used when assembling small parts, these small clamps have the holding strength of a full-size clamp.

Weld these clamps to the side of an object or drill your own holes in the mounting plate and bolt into place.

Attach one of these nonmarring rubber or plastic tips to prevent a metal holding screw from damaging workpiece surfaces.

These clamps have mounting holes on the bottom.

Press the trigger to slide the clamping arm along the bar. Release the trigger and squeeze the pistol‐grip handle to lock the clamp in place.

Hold up to five times the capacity of standard bar clamps. These are also known as I-beam clamps.

Two swivel pads on each jaw pivot to grip nearly any shape of material.

Place the arms on a pipe that is threaded at one end and at least 12" long to create your own bar clamp.

The clamping arm slides freely along the bar for quick, one handed positioning. Tighten the screw onto a workpiece and the arm locks in place.

Also known as J-clamps, these provide additional clearance to reach around obstructions and clamp workpieces in recessed areas.

All adjustments can be made from one end, allowing clamping in tight spaces.

Clamp much farther in from the edge of the workpiece than with standard bar clamps.

Plastic clamping surfaces prevent damage to material.

Clamp farther in from the edge of a workpiece than with other C-clamps.

All components of these clamps are made of aluminum-bronze that is Factory Mutual approved. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

With no handle or protruding screw, these clamps can fit into tight spaces.

With five times the capacity of standard C-clamps, these are the highest capacity clamps we offer.

These clamps have twice the capacity of standard C-clamps.

Push the lever to lock the handle and prevent accidental opening.

Push the lever to lock the handle and prevent accidental opening.

The jaws move in unison to apply even pressure and prevent twisting.

Apply pressure to the side of a workpiece as well as the top and bottom.

The matching jaws are ground flat for a firm grip and even pressure when clamping smooth surfaces.

Squeeze the handles to open the clamp; release and the spring holds it tightly in place.

Attached to an arm you can flex into position, these clamps hold objects such as a flashlight, tool, or instructions.

Hold lightweight objects, secure covers, and seal bags.

Slide the upper jaw to adjust the opening size. These clamps hold larger workpieces than other locking plier clamps of similar size.

Clamp thin materials, or use in tight spaces.

Set includes 12 clamps and the installation pliers required for positioning and removal.

Hold large workpieces with a standard-size clamp. Slide the jaws to adjust the opening size.

Mount using the holes in the base.

Use these fittings in an air vacuum system to avoid the hassle of brazing and welding. Insert two fittings into a clamp and tighten to form a secure seal in steel tubing.

Connect extra-support quick-clamp fittings for a fast and easy way to access your line.

Connect quick-clamp fittings in high-vacuum applications.

Repair pinholes, punctures, and cracks in low-pressure systems with these clamps. Insert tubing into the clamp and tighten the bolts to create a secure seal.

Use these fittings to make leak-resistant connections without threading or soldering. Slide them over tubing and turn the end nuts to compress the gasket.

Use these clamps with quick-clamp fittings for dairy to quickly connect and disconnect your line as needed.

Also known as manifold flange fittings, these have a clamp-together design that lets you access your line for routine maintenance. Fittings resist acids, solvents, and other harsh chemicals. They won’t deteriorate when exposed to the damaging effects of ultraviolet light, so they’re suitable for outdoor use.

The grooved ends on these flanges connect to pipe with a clamp, so you can access your chemical process line for routine maintenance. Flanges have excellent chemical resistance to withstand a variety of salt solutions, acids, and other harsh substances. They are also known as Victaulic flanges.

Also known as Victaulic pipe, this pipe has grooved ends that connect to fittings and flanges with a clamp, so you can access your line for routine maintenance. It is CPVC, which has excellent chemical resistance to withstand a variety of salt solutions, acids, and other harsh substances.

Connect these fittings to Schedule 40 plastic pipe—they are the industry standard for residential and commercial low-pressure plumbing and water supply applications. They are plastic for good corrosion resistance.

Connect these fittings to thick-wall plastic pipe—they have thicker, stronger walls than standard-wall fittings, so they can handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. They can withstand pressures up to 900 psi.

These connectors are for use in low-pressure air and vacuum conveying systems, as well as in gravity-flow systems.

Also known as no-hub couplings, these have a one-piece sleeve with a stop in the center, so you know your pipe is always aligned correctly.

These fittings can stand up to high-pressure applications. Use them in noncorrosive environments.

Use these fittings for low-pressure applications in noncorrosive environments.

Install in a cutout to create a secure joint between boards, butcher blocks, and countertops.

Thick construction makes this framing strong and sturdy.

To provide corrosion resistance in wet environments, this framing is galvanized.

Attach sensors, tubes, and other components to T-slotted framing rails and structures.

Half the weight of steel, this aluminum framing resists corrosion in wet environments.