Also known as rod‐end bearings, ball joint rod ends have an eyelet and a ball that swivels to support angular misalignment.

A carbon fiber-reinforced insert or PTFE liner reduces wear, handles shock loads, and eliminates the need for lubrication.

Connect your grease gun to the fitting to lubricate. Internal threads mate with rod end bolts, threaded rods, and other components with male threads.

An oil-embedded bronze insert slowly releases lubricant to the rod end. Connect your grease gun to the fitting to relubricate.

Made of stainless steel, these externally threaded rod ends provide excellent corrosion resistance.

Made of impact-resistant nylon, these internally threaded rod ends withstand corrosion as well as fuels, lyes, and weak acids. They do not require lubrication and are 80% lighter than steel rod ends.

These externally threaded steel rod ends handle loads that are at least 25% higher than other comparably sized rod ends.

These internally threaded rod ends have an innovative body design that keeps the ball from being pushed out when supporting thrust loads.

A double row of precision ball bearings allows high speeds and smooth operation.

These linkages offer excellent wear resistance. They consist of internally threaded ball joint rod ends with a ball stud attached to simplify mounting.

These ball joint linkages are made of steel.

Use these linkages to create inline pivoting connections. They have internal threads on one end and external threads on the other.

These steel rod ends are machined to SAE standards.

These rod end bolts are good for wet and corrosive environments—for maximum mounting flexibility, cut the fully threaded shaft to whatever length you need.

Good for general purpose applications where corrosion and high strength aren’t a concern, these rod end bolts are made of carbon steel.

Pivot and hinge components in wet and corrosive environments with these stainless steel or brass rod end bolts.

A slippery PTFE liner reduces wear and eliminates the need for lubrication.

A slippery PTFE liner reduces wear and eliminates the need for lubrication.

Attach these nuts to rods, pipes, and tubes to make pivoting and hinge movements where misalignment is not a concern.

Use these corrosion-resistant fittings in a low-pressure pipe line.

Use these heavy duty, corrosion-resistant fittings in high-pressure flow applications.

Bolt two same-size flanges together with a gasket to create an access point within a pipe line.

These fittings are strong enough to handle extreme pressures, yet small enough to fit into cramped spaces.

These brass fittings have the strength to handle high-pressure applications.

In addition to being lightweight, these aluminum fittings offer good corrosion resistance. Use them in low-pressure flow applications.

Connect these fittings to Schedule 40 plastic pipe—they are the industry standard for residential and commercial low-pressure plumbing and water supply applications. They are plastic for good corrosion resistance.

Connect these fittings to thick-wall plastic pipe—they have thicker, stronger walls than standard-wall fittings, so they can handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. They can withstand pressures up to 900 psi.

This polypropylene pipe resists the damaging effects of ultraviolet light, so it’s suitable for outdoor use. It has the chemical resistance to withstand acids, solvents, and other harsh substances.

Solder these fittings to tubing for a permanent, leak-tight connection. They are also known as sweat fittings.

With a nickel-plated finish, these compression fittings resist corrosion better than plain brass fittings.

Connect quick-clamp sanitary tube fittings—also known as aseptic fittings—for a fast and easy way to access your line.

Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on steel tubing that is flared to 37°.

Thicker walls make these fittings—sometimes called flareless or bite fittings—withstand about twice as much pressure as standard compression fittings, so they’re good for hydraulic power applications.

Make lightweight connections without the hassle of matching the exact thread type—these fittings connect to NPT, NPTF, BSPP, BSPT, and other universal threads.

Often used in outdoor, damp, and washdown environments, these 316 stainless steel fittings will not corrode from water, salt, or chemicals. The male threaded ends mate with NPT, NPTF, BSPT, BSPP, and other universal threads, so you won’t have to worry about matching exact threads when you’re on the job.

A 316 stainless steel body gives these fittings the best corrosion resistance of all our metal push-to-connect tube fittings.

Withstanding temperatures up to 300° F, these fittings have the highest temperature rating of all our push-to-connect tube fittings for air and water.

The threads on these fittings mate with NPT, NPTF, BSPT, and BSPP threads.

Designed for use in welding applications, these fittings are flame retardant.

Use at pressures up to 150 psi.

Barbs grip onto tubing.

Fittings have good corrosion resistance.

Made of stainless steel, these fittings have better corrosion resistance than brass fittings.

Made of acetal, these compression fittings are lighter in weight than metal compression fittings and won’t absorb moisture when used in wet environments.

Also known as instant fittings, these chemical-resistant plastic fittings connect to tubing with a push, and an internal gripping ring and fluoroelastomer O-ring hold the tubing tight.

Made of PVDF (also known as Kynar), these fittings have excellent strength and can handle temperatures as high as 240° F or 270° F.

Made of brass, these fittings withstand frequent washdowns in food-processing applications. They also adhere to NSF/ANSI safety standards, so they’re safe to use with food, beverages, and dairy.

These fittings keep their strength in moist environments and meet NSF/ANSI 61 for drinking water. Also known as instant fittings.

Metal hose fittings have better durability than plastic barbed hose fittings.

Designed for coolant applications up to 200 psi, these fittings have a standard barbed end that slides into hose and secures with a clamp.

Pivots provide smooth motion at the junction between two T-slotted rails.

Attach sensors, tubes, and other components to T-slotted framing rails and structures.

Seal T-slots, rail ends, and gaps between rails to keep out dust, debris, and other contaminants.

These U-joints are made of steel or zinc.