Tighten the screws to secure your cable.

An insert clamps the cable in place to provide more strain relief than other snap-in cord grips for building cable.

These cord grips are lightweight yet durable.

The mesh extension provides a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

These grips install into enclosure holes quickly to stabilize and relieve strain on cords.

Made of nylon, these grips resist chemicals.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

These grips are sized to fit in tight areas.

Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.

Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.

These 90° elbows absorb less water and are less likely to crack or corrode than other types of plastics and metals.

Push to install these cord grips in wet environments and high-movement applications such as robotics and handheld equipment.

Snap these cord grips into place to secure cable in wet environments.

These grips are made of nylon, which resists most chemicals. The nylon mesh extension provides a secure hold when the cable is pulled or in motion.

Made of PBT, these grips resist soaking up water in washdown and other wet environments while securing cords with an extra-strong hold.

Lighter in weight than steel and brass grips, these aluminum grips are strong enough to secure cords in demanding wet environments.

Create a tight grip on cords in wet environments while reducing stress from bending—the 90° angle of these cord grips routes cords to fit tight spaces in enclosures and panels.

Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

Keep cords from coming loose and seal water out of enclosures in extremely cold labs and storage areas. Thanks to their plastic bushing and rubber O-ring, these grips withstand temperatures as low as -75° F.

These grips have an extension that provides extra support for moving cable and prevents kinking for longer cable life.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

Also known as cable-entry seals, the cable-entry side has heat-shrinkable polyolefin with an adhesive lining.

Secure cords in wet and industrial environments with little room—these grips curve 45° to relieve bending stress.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These stainless steel grips offer the most protection from wet, corrosive environments of any of our metal wet-location cord grips. They are rated IP67 for protection from temporary water submersion.

These grips are nickel-plated brass for good corrosion resistance.

These grips meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

Attach a cord grip to cable without removing connectors and rewiring. These cord grips have a two-piece design to fit around cables with connectors.

Secure multiple flat cable through one cord grip—reducing the space and number you need for a project, as well as saving time.

Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection.

Attach conduit to a knockout in an outlet box or enclosure.

Attach conduit to a knockout in an outlet box or enclosure.

Attach conduit to a knockout in an outlet box or enclosure.

Attach conduit to a knockout in an outlet box or enclosure.

Attach conduit and armored cable to a knockout in an outlet box or enclosure.

Attach conduit to a knockout in an outlet box or enclosure.

Attach conduit to a knockout in an outlet box or enclosure.