Combine power, USB, computer, and compressed air inserts to build a connector that sends signal, power, and data. A complete connector requires a hood, a base, two frames, and a male and female insert for each slot in the frame. The frames fit into the hood and base, and the inserts snap into the frame. Select components based on the number of slots needed. Once assembled, connectors are rated NEMA 4X, 12, and IP65 for protection against dirt, washdowns, and oil/coolant dripping.

Use USB adapters with USB holders to connect two male USB cords.

Crimpers (sold separately) are required for wire installation for crimp-on connectors. They ratchet to ensure the correct pressure is applied to every crimp.

Use positioners (sold separately) with crimpers to hold pins and sleeves at the correct height while crimping.

Extraction tools (sold separately) make it easier to remove pins or sleeves from 17- and 20-pole power inserts.

Insertion/Extraction tools (sold separately) make it easier to install DB25 inserts.

For technical drawings and 3-D models, click on a part number.

Configure a connector for your application—combine male and female inserts with a base and a hood. Select components based on the number of poles needed. To protect connections while maintaining access, the base and hood latch together securely, yet can be quickly detached for equipment repair or replacement. Once assembled, these connectors are rated NEMA 4X, 12, and IP65 for protection against corrosion, washdowns, dirt, oil/coolant dripping, and water projected from a nozzle.

For technical drawings and 3-D models, click on a part number.

Protect connections while maintaining access. The base and hood latch together securely yet can be quickly detached for equipment repair or replacement.

Latching connectors with one latching lever quickly disconnect with one hand. Connectors with two latching levers don’t need as much room to unlatch as connectors with one latching lever and are best for tight spaces.

Latching connectors with cord grips secure cable and protect it from strain. Choose connectors with two cord grips to create a disconnection point on curved or compact equipment that cannot have a panel cutout.

NEMA 4X rated connectors protect against washdowns. NEMA 12 rated connectors resist oil/coolant dripping. IP65 rated connectors protect against dust and rinsing. IP66 rated connectors protect against washdowns.

For technical drawings and 3-D models, click on a part number.

Able to carry more than twice the current of standard latching signal/power connectors, these can be used with thermosensors or brakes on large motors. Use them to protect connections while maintaining access. The base and hood latch together securely, yet can be quickly detached for equipment repair or replacement. They’re rated NEMA 4X, 12, and IP65 for protection against corrosion, washdowns, dirt, oil/coolant dripping, and water projected from a nozzle.

4-pole connector has two control pins to prevent arcing if it is disconnected before the power is turned off.

For technical drawings and 3-D models, click on a part number.

Rated NEMA 4X, 12, and IP65, connectors protect against corrosion, washdowns, oil/coolant dripping, and water projected from a nozzle. They have a rubber seal and stainless steel hardware for excellent chemical resistance. Use them to protect connections while maintaining access. The base and hood latch together securely, yet can be quickly detached for equipment repair or replacement.

For technical drawings and 3-D models, click on a part number.

The smallest latching connectors we offer, these fit in tight spaces. Use them to protect connections while maintaining access. The base and hood latch together securely yet can be quickly detached for equipment repair or replacement.

Latching connectors with cord grips protect cable from strain and remain secure even if cable is accidentally tugged. Connectors with two cord grips are typically used to create a disconnection point on equipment that cannot have a panel cutout, such as curved or compact equipment.

Screw terminal wire connections do not require special tools to create connections. Crimp on wire connections are more secure than screw terminal wire connections and hold up to bending and twisting. Use a crimping tool to install the crimping pins. For 12-pole connectors, you also need a positioner to hold pins at the correct height while crimping. Crimping tool and positioner are both sold separately.

NEMA 4X rated connectors protect against washdowns. NEMA 12 rated connectors resist oil/coolant dripping. IP65 rated connectors protect against dust and rinsing. IP67 rated connectors can be temporarily submerged.

For technical drawings and 3-D models, click on a part number.

Carry up to four times the current of standard compact latching signal/power connectors. To protect connections while maintaining access, the base and hood latch together securely, yet can be quickly detached for equipment repair or replacement. They’re rated IP65 for protection against dirt and water projected from a nozzle.

For technical drawings and 3-D models, click on a part number.

Push these connectors together to quickly create signal and data connections in tight spaces. They need less space to mate than screw-together connectors, which require two hands to twist them in place. However, screw-together connectors offer a more secure hold. These connectors have pin connections and a half-round or V-notched face for a snug fit that resists shock and vibration. Rated for over 2,000 mating cycles, the pins stand up to repeated connections and disconnections. Plugs can only mate with sockets of the same size, latch option, and pole count.

Connectors with a solder connection have solder cup terminals that hold wire leads in place when you’re soldering them. They form more secure connections than standard solder terminals.

Connectors with a wire lead connection come with wire leads attached to save you time on installation.

Connectors with a built-in latch keep your mated connections secure.

For technical drawings and 3-D models, click on a part number.