Glow-in-the-dark vials are easy to read in low light.

One of the horizontal vials is a pitch gauge that reads slope in 1/8" increments.

Lightweight yet strong and durable, these bamboo levels won't stick to wet cement. Also known as masonry levels.

These levels have a plastic housing.

A color LCD and highly accurate sensor allow you to level both horizontally and vertically at the same time.

A color LCD and highly accurate sensor allow you to level both horizontally and vertically at the same time. This level also displays a real-time vibration graph.

With a precision-machined leveling surface and highly sensitive vial, this level provides superior accuracy.

Mount these levels to a table or other horizontal surface and they will indicate when you're level on the horizontal plane.

Stick these levels onto carts, mobile equipment, and other horizontal surfaces to make sure they're level before use. The adhesive backing forms a permanent hold with no drilling or fasteners required.

Use this compact instrument to establish a level sight line.

In addition to the instrument, you get a leveling rod and tripod.

Use these telescoping rods in conjunction with sight levels. They extend to the length you need, then collapse for convenient storage.

A magnet keeps this 90° level in place while you position posts and corners.

Twist the head to switch between a dot, a horizontal line, or a vertical line.

Whether you’re hanging a drop ceiling or aligning bench tops, use the cross-hair lines of these lasers to install material at the right height.

These kits include a laser, a beam splitter, and a leveling plate.

Mount these lasers into a chuck on your milling machine or drill press to precisely indicate the drilling point.

Fine-tune the size of the laser dot.

These lasers are sized for mounting on machinery to ensure tools are properly positioned.

With a sealed lens and an IP67 rating, these lasers are dust and liquid tight, so you can mount them to machines in dusty or wet areas such as labs, warehouses, or marine environments to align components.

Slip this tool into your pocket so it's on hand to align belts, pulleys, chain, and sprockets.

At 2 1/4" square and 1" wide, this angle indicator easily fits into your pocket.

These angle indicators display highly accurate angle, level, and tilt measurements.

The LCD on these digital angle indicators shows angle in degrees and percent of slope.

The electronic sensor and the display are connected by a 4‐ft. cable so you can measure angles from a distance. They can be mounted up to 150 feet apart by replacing the included cable with a longer cable length.

Temporarily mount these indicators to a metal surface. They have four quadrants that each read any angle from 0° to 90°.

A ball inside a level tube indicates the side-to-side tilt angle.

These tools have front and back digital displays, as well as horizontal and vertical vials.

Replace your try square, miter square, depth gauge, marking gauge, 90° level, ruler, and scriber with one tool.

Attach to High-Accuracy Combination Square Blades with the included lockbolts.

Replace your try square, miter square, depth gauge, height gauge, center-point finder, and level. The blade on these squares meets Fed. Spec. GGG-R-791H, which establishes uniform standards for accuracy, graduations, and size.

A titanium coating protects the blade against scratches and wear.

Measure volume in gallons without calculations.

Built to resist corrosion and last in harsh environments, these vertical rulers are iron with a porcelain-enamel finish. Mount them to walls and tanks.

Connect continuous segments to create a ruler up to 10 ft. long.

Attach a plumb bob (sold separately) to the rope’s hook and lower it into your tank to take a measurement.

Also known as oil-gauging tapes, use these tape measures to check the level of oil and other fluids in deep, large containers such as tanks and vats.

Reach deep into small holes and slots for precise depth measurements.

Nickel-plated steel has some corrosion resistance.

Yellow zinc-plated steel is more corrosion resistant than nickel-plated steel.

An economical choice for applications in corrosive environments that don't require high load capacities, these mounts have a plastic base.

Made of 303 stainless steel, these metric mounts resist corrosion from water and most chemicals.

Made entirely of 316 stainless steel, these metric mounts have superior corrosion resistance.

Punch-out holes in the base let you bolt down these mounts to keep your equipment stationary.

Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance.

Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance.

Nickel-plated steel has some corrosion resistance.

An economical choice for applications in corrosive environments that don't require high load capacities, these mounts have a plastic base.

Made of 303 stainless steel, these metric mounts resist corrosion from water and most chemicals.

Well-suited to damp environments, these mounts have a stainless steel nut for excellent corrosion resistance.

Use these mounts on heavy machines and equipment.

A hex nut at the base of the stud allows for easy height adjustment.

Made of 303 stainless steel, these metric mounts resist corrosion from water and most chemicals.