About Durometer Hardness Scales
More
About Leveling Mounts
More
About Vibration-Damping Mounts
More
Nickel-Plated Steel Swivel Leveling Mounts with Threaded Stud
Nickel-plated steel has some corrosion resistance. Mounts have a ball-and-socket design that swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Metric Yellow Zinc-Plated Steel Swivel Leveling Mounts with Threaded Stud
Yellow zinc-plated steel is more corrosion resistant than nickel-plated steel. Mounts have a ball-and-socket design that swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Metric Corrosion-Resistant Swivel Leveling Mounts with Threaded Stud
Made entirely of stainless steel, these mounts resist corrosion from water and most chemicals. Their ball-and-socket design swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Metric Super-Corrosion-Resistant Swivel Leveling Mounts with Threaded Stud
Made entirely of 316 stainless steel, these mounts have superior corrosion resistance. Their ball-and-socket design swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
For technical drawings and 3-D models, click on a part number.
Thread Size | Thread Pitch, mm | Thread Lg., mm | Capacity per Mount, lbs. | Base Dia., mm | Overall Ht., mm | Hex Nut Wd., mm | Each | |
316 Stainless Steel | ||||||||
---|---|---|---|---|---|---|---|---|
M12 | 1.75 | 51 | 4,950 | 48 | 79 | 20 | 0000000 | 000000 |
Metric Bolt-Down Swivel Leveling Mounts with Threaded Stud
Punch-out holes in the base let you bolt down these mounts to keep your equipment stationary. Their ball-and-socket design swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Mounting Holes | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Thread Pitch, mm | Thread Lg., mm | Capacity per Mount, lbs. | Base Dia., mm | Overall Ht., mm | Hex Nut Wd., mm | Temperature Range, °F | Mounting Fasteners Included | No. of | Dia., mm | Ctr.-to-Ctr. Lg., mm | Each | |
Plastic with Zinc-Plated Steel Stud | |||||||||||||
M12 | 1.75 | 76 | 4,000 | 51 | 105 | 20 | -20° to 170° | No | 2 | 6.4 | 33.8 | 0000000 | 00000 |
M12 | 1.75 | 76 | 5,000 | 101.9 | 109 | 20 | -20° to 170° | No | 2 | 12.5 | 68.8 | 00000000 | 00000 |
M12 | 1.75 | 102 | 4,000 | 51 | 130 | 20 | -20° to 170° | No | 2 | 6.4 | 33.8 | 0000000 | 00000 |
M12 | 1.75 | 102 | 5,000 | 76 | 130 | 20 | -20° to 170° | No | 2 | 8.9 | 55.9 | 00000000 | 00000 |
M12 | 1.75 | 102 | 5,000 | 102 | 135 | 20 | -20° to 170° | No | 2 | 11.9 | 68.8 | 00000000 | 00000 |
M12 | 1.75 | 152 | 4,000 | 51 | 181 | 20 | -20° to 170° | No | 2 | 6.4 | 33.8 | 0000000 | 0000 |
M12 | 1.75 | 152 | 5,000 | 76 | 181 | 20 | -20° to 170° | No | 2 | 8.9 | 55.9 | 0000000 | 00000 |
M12 | 1.75 | 152 | 5,000 | 102 | 185 | 20 | -20° to 170° | No | 2 | 11.9 | 68.8 | 0000000 | 00000 |
M12 | 1.75 | 203 | 4,000 | 51 | 232 | 20 | -20° to 170° | No | 2 | 6.4 | 33.8 | 00000000 | 00000 |
M12 | 1.75 | 203 | 5,000 | 102 | 236 | 20 | -20° to 170° | No | 2 | 11.9 | 68.8 | 00000000 | 00000 |
Plastic with Rubber Cushion and Zinc-Plated Steel Stud | |||||||||||||
M12 | 1.75 | 76 | 4,000 | 51 | 106.6 | 20 | -20° to 170° | No | 2 | 6.4 | 33.8 | 0000000 | 00000 |
M12 | 1.75 | 76 | 5,000 | 102 | 110.6 | 20 | -20° to 170° | No | 2 | 11.9 | 68.8 | 00000000 | 00000 |
M12 | 1.75 | 102 | 4,000 | 51 | 131.6 | 20 | -20° to 170° | No | 2 | 6.4 | 33.8 | 0000000 | 00000 |
M12 | 1.75 | 102 | 5,000 | 76 | 131.6 | 20 | -20° to 170° | No | 2 | 8.9 | 55.9 | 00000000 | 00000 |
M12 | 1.75 | 102 | 5,000 | 102 | 136.6 | 20 | -20° to 170° | No | 2 | 11.9 | 68.8 | 00000000 | 00000 |
M12 | 1.75 | 152 | 4,000 | 51 | 182.6 | 20 | -20° to 170° | No | 2 | 6.4 | 33.8 | 0000000 | 00000 |
M12 | 1.75 | 152 | 5,000 | 102 | 186.6 | 20 | -20° to 170° | No | 2 | 11.9 | 68.8 | 0000000 | 00000 |
M12 | 1.75 | 203 | 4,000 | 51 | 233.6 | 20 | -20° to 170° | No | 2 | 6.4 | 33.8 | 00000000 | 00000 |
M12 | 1.75 | 203 | 5,000 | 76 | 233.6 | 20 | -20° to 170° | No | 2 | 8.9 | 55.9 | 00000000 | 00000 |
M12 | 1.75 | 203 | 5,000 | 102 | 237.6 | 20 | -20° to 170° | No | 2 | 11.9 | 68.8 | 00000000 | 00000 |
Metric Corrosion-Resistant Bolt-Down Swivel Leveling Mounts with Threaded Stud
Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance. Use the punch-out holes in the base to bolt down mounts to keep your equipment stationary. Their ball-and-socket design swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Mounting Holes | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Thread Pitch, mm | Thread Lg., mm | Capacity per Mount, lbs. | Base Dia., mm | Overall Ht., mm | Hex Nut Wd., mm | Temperature Range, °F | Mounting Fasteners Included | No. of | Dia., mm | Ctr.-to-Ctr. Lg., mm | Each | |
Plastic with 303 Stainless Steel Stud | |||||||||||||
M12 | 1.75 | 76 | 4,000 | 51 | 105 | 20 | -20° to 170° | No | 2 | 6.4 | 33.8 | 0000000 | 000000 |
M12 | 1.75 | 102 | 5,000 | 76 | 130 | 20 | -20° to 170° | No | 2 | 8.9 | 55.9 | 00000000 | 00000 |
M12 | 1.75 | 102 | 5,000 | 102 | 135 | 20 | -20° to 170° | No | 2 | 11.9 | 68.8 | 00000000 | 00000 |
M12 | 1.75 | 152 | 4,000 | 51 | 181 | 20 | -20° to 170° | No | 2 | 6.4 | 33.8 | 0000000 | 00000 |
M12 | 1.75 | 152 | 5,000 | 102 | 185 | 20 | -20° to 170° | No | 2 | 11.9 | 68.8 | 0000000 | 00000 |
Plastic with Rubber Cushion and 303 Stainless Steel Stud | |||||||||||||
M12 | 1.75 | 76 | 4,000 | 51 | 106.6 | 20 | -20° to 170° | No | 2 | 6.4 | 33.8 | 0000000 | 00000 |
M12 | 1.75 | 152 | 4,000 | 51 | 182.6 | 20 | -20° to 170° | No | 2 | 6.4 | 33.8 | 0000000 | 00000 |
M12 | 1.75 | 152 | 5,000 | 102 | 186.6 | 20 | -20° to 170° | No | 2 | 11.9 | 68.8 | 0000000 | 00000 |
Metric Yellow Zinc-Plated Steel Swivel Leveling Mounts with Threaded Hole
Yellow zinc-plated steel is more corrosion resistant than nickel-plated steel. Mounts have a ball-and-socket design that swivels to compensate for uneven floors. Add your own threaded stud or bolt to build a mount that fits your needs. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Metric Corrosion-Resistant Swivel Leveling Mounts with Threaded Hole
Made of stainless steel, these mounts resist corrosion from water and most chemicals. Their ball-and-socket design swivels to compensate for uneven floors. Add your own threaded stud or bolt to build a mount that fits your needs. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a rubber cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Thread Size | Thread Pitch, mm | Thread Dp., mm | Capacity per Mount, lbs. | Base Dia., mm | Overall Ht., mm | Hex Nut Wd., mm | Temperature Range, °F | Performance | Each | |
303 Stainless Steel | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
M12 | 1.75 | 11.1 | 4,950 | 48 | 29 | 20 | -20° to 170° | Corrosion Resistant | 0000000 | 000000 |
303 Stainless Steel with Rubber Cushion | ||||||||||
M12 | 1.75 | 11.1 | 3,745 | 48 | 32 | 20 | -20° to 170° | Antislip, Corrosion Resistant | 0000000 | 00000 |
Metric Heavy Duty Leveling Mounts with Threaded Stud
Use these mounts on heavy machines and equipment. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection. They're zinc plated for corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Thread Size | Thread Pitch, mm | Thread Lg., mm | Capacity per Mount, lbs. | Base Dia., mm | Overall Ht., mm | Temperature Range, °F | Features | Each | |
Zinc-Plated Steel | |||||||||
---|---|---|---|---|---|---|---|---|---|
M12 | 1.75 | 51 | 250 | 61 | 76 | -20° to 170° | Nonmarring Plastic Bottom | 00000000 | 00000 |
M12 | 1.75 | 51 | 500 | 71 | 76 | -20° to 170° | Nonmarring Plastic Bottom | 00000000 | 0000 |
M12 | 1.75 | 102 | 250 | 61 | 127 | -20° to 170° | Nonmarring Plastic Bottom | 00000000 | 0000 |
M12 | 1.75 | 102 | 500 | 71 | 127 | -20° to 170° | Nonmarring Plastic Bottom | 00000000 | 0000 |
M12 | 1.75 | 102 | 500 | 81 | 127 | -20° to 170° | Nonmarring Plastic Bottom | 00000000 | 00000 |
M12 | 1.75 | 152 | 500 | 81 | 178 | -20° to 170° | Nonmarring Plastic Bottom | 00000000 | 00000 |
Metric Corrosion-Resistant Leveling Mounts with Threaded Stud
Made of 303 stainless steel, these mounts resist corrosion from water and most chemicals. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
For technical drawings and 3-D models, click on a part number.
Corrosion-Resistant Swivel Vibration-Damping
Leveling Mounts with Threaded Stud
All-stainless steel construction stands up to water and chemicals and won't rust or corrode. Use these mounts to minimize vibration and noise to prolong machine life and protect floors. Their ball-and-socket design swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
For technical drawings and 3-D models, click on a part number.
Thread Size | Thread Pitch, mm | Thread Lg. | Capacity per Mount, lbs. | Deflection @ Capacity | Base Dia. | Overall Ht. | Temperature Range, °F | Each | |
304 Stainless Steel with Rubber Cushion | |||||||||
---|---|---|---|---|---|---|---|---|---|
M12 | 1.75 | 4 3/4" | 500 | 0.07" | 2 5/8" | 5 11/16" | 0° to 200° | 0000000 | 000000 |
M12 | 1.75 | 4 3/4" | 1,000 | 0.12" | 3 7/8" | 6 1/8" | 0° to 200° | 0000000 | 00000 |
M12 | 1.75 | 4 3/4" | 2,000 | 0.12" | 3 7/8" | 6 1/8" | 0° to 200° | 0000000 | 00000 |
Bolt-Down Swivel Vibration-Damping Leveling Mounts with Threaded Stud
Bolt these mounts down to keep your equipment stationary. Use them to minimize vibration and noise to prolong equipment life and protect floors. Mounts have a ball-and-socket design that swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection. They're made of stainless steel for corrosion resistance when exposed to water and most chemicals.
Mounts with one mounting hole are good for tight locations.
For technical drawings and 3-D models, click on a part number.
Thread Size | Thread Pitch, mm | Thread Lg. | Capacity per Mount, lbs. | Deflection @ Capacity | Base Dia. | Base Ht. | Overall Ht. | Temperature Range, °F | Mounting Fasteners Included | Mount. Hole Dia. | Each | |
304 Stainless Steel with Rubber Cushion | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
One Mounting Hole | ||||||||||||
M12 | 1.75 | 3 15/16" | 1,770 | 0.06" | 2 15/16" | 7/8" | 4 13/16" | 0° to 200° | No | 5/8" | 00000000 | 000000 |
Extreme-Force Swivel Vibration-Damping Leveling Mounts with Threaded Stud
Higher deflection ratings translate to greater vibration and shock isolation. These mounts have a rubber base that grips the floor for stability and is resistant to oil and grease. Their ball-and-socket design swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
For technical drawings and 3-D models, click on a part number.
Thread Size | Thread Pitch, mm | Thread Lg. | Capacity per Mount, lbs. | Deflection @ Capacity | Swivel Range of Motion | Base Lg. | Base Wd. | Base Ht. | Overall Ht. | Hardness | Hardness Rating | Temp. Range, °F | Each | |
Rubber with Zinc-Plated Steel Stud | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
M12 | 1.75 | 2 5/8" | 350 | 0.13" | 7.5° | 3" | 3" | 5/8" | 3 7/16" | Durometer 50A | Medium | -20° to 180° | 00000000 | 000000 |
M12 | 1.75 | 2 5/8" | 700 | 0.13" | 7.5° | 3" | 3" | 5/8" | 3 7/16" | Durometer 70A | Hard | -20° to 180° | 00000000 | 00000 |
Thread Size | Thread Pitch, mm | Thread Lg. | Capacity per Mount, lbs. | Deflection @ Capacity | Swivel Range of Motion | Base Dia. | Base Ht. | Overall Ht. | Hardness | Hardness Rating | Temp. Range, °F | Each | |
Rubber with Zinc-Plated Steel Stud | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
M12 | 1.75 | 2 3/8" | 500 | 0.13" | 7.5° | 3" | 3/4" | 3 11/16" | Durometer 50A | Medium | -20° to 180° | 00000000 | 000000 |
M12 | 1.75 | 2 3/8" | 1,000 | 0.13" | 7.5° | 3" | 3/4" | 3 11/32" | Durometer 70A | Hard | -20° to 180° | 00000000 | 00000 |
Metric High-Capacity Leveling Mount Inserts for Tubular Legs
Rated for high load capacity, use these inserts to connect threaded leveling mounts to machinery, instrument bases, and conveyor equipment with tubular legs. These inserts have pass-through holes that are partially threaded at the base. Tap mounts into place with a rubber hammer.
For technical drawings and 3-D models, click on a part number.
Load-Rated Threaded-Stud Bumpers
Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Twist these bumpers into a threaded hole.
Bumpers with a medium hardness rating offer a balance of cushioning and impact resistance.
Bumpers with a hard hardness rating withstand more impact than softer bumpers.
Rubber bumpers are abrasion resistant. Those with a soft rating can be used outdoors.
Stainless steel studs are more corrosion resistant than steel studs.
For technical drawings and 3-D models, click on a part number.
Thread | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size | Pitch, mm | Lg. | OD | Ht. | Max. Load, lbs. | Temp. Range, °F | For Use Outdoors | Hardness Rating | Nonmarking | Color | Stud Material | Each | |
Style 1 | |||||||||||||
Rubber with Steel Base Plate | |||||||||||||
M12 | 1.75 | 37mm | 75mm | 25mm | 2,170 | -40° to 170° | No | Medium | No | Black | Steel | 00000000 | 000000 |
M12 | 1.75 | 37mm | 75mm | 25mm | 4,670 | -40° to 170° | No | Hard | No | Black | Steel | 00000000 | 00000 |
M12 | 1.75 | 37mm | 75mm | 40mm | 1,500 | -40° to 170° | No | Medium | No | Black | Steel | 00000000 | 00000 |
M12 | 1.75 | 37mm | 75mm | 40mm | 2,060 | -40° to 170° | No | Hard | No | Black | Steel | 00000000 | 00000 |
M12 | 1.75 | 37mm | 75mm | 50mm | 980 | -10° to 150° | No | Medium | No | Black | Steel | 000000000 | 00000 |
M12 | 1.75 | 37mm | 75mm | 50mm | 3,040 | -40° to 170° | No | Hard | No | Black | Steel | 00000000 | 00000 |
Rubber with Stainless Steel Base Plate | |||||||||||||
M12 | 1.75 | 37mm | 75mm | 25mm | 2,170 | -40° to 170° | No | Medium | No | Black | Stainless Steel | 00000000 | 00000 |
Heavy Duty Threaded-Stud Bumpers
All of these bumpers are reinforced with a steel core for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. Twist them into a threaded hole. All are nonmarking and can be used outdoors.
Bumpers with a hard rating withstand high levels of impact. Bumpers with a medium-soft rating offer a balance of cushioning and impact resistance.
Neoprene bumpers have good abrasion resistance.
Polyurethane bumpers have better abrasion resistance than neoprene bumpers. They won't become brittle and crack when exposed to ozone.
For technical drawings and 3-D models, click on a part number.
Thread | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size | Pitch, mm | Lg. | OD | Ht. | Overall Ht. | Temp. Range, °F | For Use Outdoors | Hardness Rating | Hardness | Nonmarking | Color | Each | |
Style 1 | |||||||||||||
Neoprene Rubber with Steel Core | |||||||||||||
M12 | 1.75 | 30mm | 32mm | 32mm | 62mm | -40° to 200° | Yes | Hard | Durometer 75A | No | Black | 00000000 | 000000 |
M12 | 1.75 | 30mm | 32mm | 32mm | 62mm | -40° to 200° | Yes | Medium Soft | Durometer 40A | No | Black | 00000000 | 00000 |
Polyurethane Rubber with Steel Core | |||||||||||||
M12 | 1.75 | 30mm | 32mm | 32mm | 62mm | -60° to 200° | Yes | Hard | Durometer 80A | No | Red | 00000000 | 00000 |
M12 | 1.75 | 30mm | 32mm | 32mm | 62mm | -60° to 200° | Yes | Medium Soft | Durometer 40A | No | Red | 0000000 | 00000 |
Load-Rated Threaded Bumpers
Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Mount these bumpers on a threaded stud. Bumpers with a medium and medium-soft rating offer a balance of cushioning and impact resistance. Bumpers with a hard rating withstand high levels of impact.
Rubber bumpers are abrasion resistant.
For technical drawings and 3-D models, click on a part number.
Thread | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size | Pitch | Dp. | OD | Ht. | Max. Load, lbs. | Temp. Range, °F | For Use Outdoors | Hardness Rating | Hardness | Nonmarking | Color | Each | |
Style 1 | |||||||||||||
Rubber with Steel Base Plate | |||||||||||||
M12 | 1.75 mm | 12mm | 75mm | 30mm | 1,770 | -40° to 170° | No | Medium | Durometer 55A | Yes | Black | 00000000 | 000000 |
M12 | 1.75 mm | 12mm | 75mm | 40mm | 1,010 | -20° to 150° | No | Medium | Durometer 55A | Yes | Black | 000000000 | 00000 |
M12 | 1.75 mm | 12mm | 75mm | 40mm | 2,060 | -40° to 170° | No | Hard | Durometer 70A | Yes | Black | 00000000 | 00000 |
M12 | 1.75 mm | 12mm | 75mm | 50mm | 980 | -20° to 150° | No | Medium | Durometer 55A | Yes | Black | 000000000 | 00000 |
Rubber with Stainless Steel Base Plate | |||||||||||||
M12 | 1.75 mm | 12mm | 75mm | 30mm | 1,770 | -40° to 170° | No | Medium | Durometer 55A | Yes | Black | 00000000 | 00000 |
M12 | 1.75 mm | 12mm | 75mm | 40mm | 1,010 | -20° to 150° | No | Medium | Durometer 55A | Yes | Black | 000000000 | 00000 |
Style 2 | |||||||||||||
Rubber with Steel Base Plate | |||||||||||||
M12 | 1.75 mm | 12mm | 75mm | 89mm | 570 | -40° to 170° | No | Hard | Durometer 70A | Yes | Black | 00000000 | 00000 |
Threaded Bumpers
Mount these bumpers on a threaded stud. All are reinforced with a steel core or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. All of these bumpers can be used outdoors.
Bumpers with a medium and medium-soft rating offer a balance of cushioning and impact resistance. The softer the bumper, the more it cushions.
Bumpers with an extra-hard, hard, and medium-hard rating withstand high levels of impact. The harder the bumper, the more impact it withstands.
Neoprene bumpers have good abrasion resistance.
Polyurethane bumpers have better abrasion resistance than neoprene bumpers. They won't become brittle and crack when exposed to ozone.
For technical drawings and 3-D models, click on a part number.
Thread | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Size | Pitch | Dp. | OD | Ht. | Temp. Range, °F | For Use Outdoors | Hardness Rating | Hardness | Nonmarking | Color | Each | |
Neoprene Rubber with Steel Core | ||||||||||||
M12 | 1.25 mm | 13mm | 32mm | 32mm | -40° to 200° | Yes | Hard | Durometer 75A | No | Black | 00000000 | 000000 |
M12 | 1.25 mm | 13mm | 32mm | 32mm | -40° to 200° | Yes | Medium Soft | Durometer 40A | No | Black | 00000000 | 00000 |
M12 | 1.75 mm | 13mm | 32mm | 32mm | -40° to 200° | Yes | Hard | Durometer 70A | No | Black | 00000000 | 00000 |
Polyurethane Rubber with Steel Core | ||||||||||||
M12 | 1.25 mm | 13mm | 32mm | 32mm | -40° to 200° | Yes | Hard | Durometer 85A | No | Red | 00000000 | 00000 |
M12 | 1.25 mm | 13mm | 32mm | 32mm | -40° to 200° | Yes | Medium | Durometer 50A | No | Red | 00000000 | 00000 |
M12 | 1.25 mm | 13mm | 32mm | 32mm | -40° to 200° | Yes | Medium Hard | Durometer 60A | No | Red | 00000000 | 00000 |
M12 | 1.25 mm | 13mm | 32mm | 32mm | -40° to 200° | Yes | Medium Soft | Durometer 40A | No | Red | 0000000 | 00000 |
M12 | 1.75 mm | 13mm | 32mm | 32mm | -40° to 200° | Yes | Extra Hard | Durometer 95A | No | Black | 00000000 | 00000 |
M12 | 1.75 mm | 13mm | 32mm | 32mm | -40° to 200° | Yes | Medium Soft | Durometer 40A | No | Black | 00000000 | 00000 |