Punch-out holes in the base let you bolt down these mounts to keep your equipment stationary. Their ball-and-socket design swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.

Mounts with a cushion are nonskid for an extra measure of stability.

For technical drawings and 3-D models, click on a part number.

Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance. Use the punch-out holes in the base to bolt down mounts to keep your equipment stationary. Their ball-and-socket design swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.

Mounts with a cushion are nonskid for an extra measure of stability.

For technical drawings and 3-D models, click on a part number.

Bolt these mounts down to keep your equipment stationary. Use them to minimize vibration and noise to prolong equipment life and protect floors. Mounts have a ball-and-socket design that swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection. They're made of stainless steel for corrosion resistance when exposed to water and most chemicals.

Mounts with one mounting hole are good for tight locations.

For technical drawings and 3-D models, click on a part number.

Thread these mounts into machinery to level them on uneven floors in sanitary environments such as food-processing areas. They also create space to clean underneath machinery. All have a hygienic thread cover that prevents contaminants from settling in the grooves. To further block out contaminants as the mount moves, as well as prevent unsanitary metal-to-metal connections, there is a silicone seal at each end of the thread cover and at the point where the mount swivels. These seals have chemical additives, so you can find them with an X-ray machine if a piece falls into your line. This helps you comply with Hazard Analysis and Critical Control Point (HACCP) programs to keep contaminated food from leaving your facility. Seals are also FDA compliant for direct contact with food.

Made of 304 stainless steel, these mounts won’t corrode from frequent washdowns with harsh cleaners and sanitizers. Their smooth finish and rounded edges leave no crevices for bacteria to grow in, reducing the chance of foodborne illnesses. They also don’t have any horizontal ledges, so liquids and food will drain off completely. Certified by 3-A, EHEDG, and USDA, they meet sanitary design standards.

The rubber cushion on the bottom reduces vibration and noise from machinery, which protects floors and extends machine life. Their grip on the floor minimizes bacteria growth beneath them and prevents machines from shifting.

These mounts swivel to level machinery on slightly uneven floors; for severely uneven floors, use the threaded stud to raise each mount to a level height.

Some mounts have mounting holes to secure them to the floor, keeping machinery stationary. Mounts with one mounting hole are secure enough to prevent machines from moving while they’re running and being cleaned. Mounts with two mounting holes reduce vibration by anchoring machinery to the floor on both sides.

For technical drawings and 3-D models, click on a part number.

Higher deflection ratings translate to greater vibration and shock isolation. These mounts have a rubber base that grips the floor for stability and is resistant to oil and grease. Their ball-and-socket design swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.

For technical drawings and 3-D models, click on a part number.

Rated for high load capacity, use these inserts to connect threaded leveling mounts to machinery, instrument bases, and conveyor equipment with tubular legs. These inserts have pass-through holes that are partially threaded at the base. Tap mounts into place with a rubber hammer.

For technical drawings and 3-D models, click on a part number.

The window and body are made from a single piece of plastic, making these sights more shatter resistant than sights with a glass window. They are not rated for pressure.

For technical drawings and 3-D models, click on a part number.