A nonreflective black oxide finish prevents glare that can interfere with machine vision systems.

Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.

The handle locks in a horizontal position for more clearance above the clamp than standard hold-down toggle clamps.

Push the lever to lock the handle and prevent accidental opening.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Push the lever to lock the handle and prevent accidental opening.

The handle locks in a horizontal position for more clearance above the clamp.

Weld these clamps to the side of an object or drill your own holes in the mounting plate and bolt into place.

Two sets of mounting holes allow mounting on the bottom or side.

Attach one of these nonmarring rubber or plastic tips to prevent a metal holding screw from damaging workpiece surfaces.

Suitable for production applications, these clamps have double the service life of other air-powered toggle clamps.

Push the lever to lock the handle and prevent accidental opening.

Push the lever to lock the handle and prevent accidental opening.

Smaller than standard push/pull toggle clamps, these are often used for electronics and small fixturing applications.

Pull the handle backward to push the plunger forward. These clamps secure when the plunger is fully extended to hold your workpiece from the side.

Smaller than standard push toggle clamps, these are often used for electronics and small fixturing applications.

The handle can be rotated 125° for easier access or extra clearance above the clamp.

Panel mount through a hole with the included nut, or drill and tap a hole to flush mount. A pushing or pulling motion holds workpieces from the side.

Secure these clamps to a rail or bar.

These clamps have twice the capacity of standard fast-action bar clamps.

Pull the handle to lock the jaw in place and prevent loosening caused by vibration.

Hold up to five times the capacity of standard bar clamps. These are also known as I-beam clamps.

All adjustments can be made from one end, allowing clamping in tight spaces.

Press the trigger to slide the clamping arm along the bar. Release the trigger and squeeze the pistol‐grip handle to lock the clamp in place.

Each arm slides freely for quick, one-handed positioning. They lock when the screws are tightened onto a workpiece.

Also known as J-clamps, these provide additional clearance to reach around obstructions and clamp workpieces in recessed areas.

Attach to your bar clamp to hold material on three sides.

With five times the capacity of standard C-clamps, these are the highest capacity clamps we offer.

A bright finish makes these clamps easy to see.

Made entirely of fiberglass, these clamps won’t transmit electricity and are chemical resistant. They're often used around electrical equipment as well as in plating and anodizing applications.

All components of these clamps are made of aluminum-bronze that is Factory Mutual approved. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Clamp farther in from the edge of a workpiece than with other C-clamps.

With no handle or protruding screw, these clamps can fit into tight spaces.

Hold the workpiece down against a bench or table.

Apply pressure to the side of a workpiece as well as the top and bottom.

Hold magnetic workpieces in place with these clamps.

Each arm has a handle for turning the magnets on and off.

Hold and align up to three workpieces at 90° angles.

Clamp up to three workpieces at 90° angles.

Hold pipe and fittings together for tack welding.

The gas valve allows you to control the gas flow at your torch instead of at the machine.

Direct the flow of shielding gas to your weld with these nozzles.

Smooth the flow of shielding gas coming out of your TIG torch nozzle, so you have more control and less waste.

Prevent shielding gas from escaping and protect torch components from excessive heat—these insulators form a seal between nozzle and torch.

Make welds quickly with these fast-melting rods.

These rods create stronger welds than standard TIG welding rods for steel.

Grind these electrodes to your exact specifications.

Grind these electrodes to your exact specifications.

These electrodes come with a 20° angle on both ends.

These electrodes come with a 20° angle on both ends.

Heat your electrode and dip it into the jar to create a point.

Make welds quickly with this fast-melting wire.

Pair this wire with an MIG gun to fuse aluminum pieces together.

Protect the cables on your MIG guns from weld spatter.

Ensure high-quality welds by protecting your welding wire from humidity and corrosion.

Keep rusty wire and wire with a poor surface finish feeding smoothly.

These electrodes are designed for optimum performance when used with an AC power source.

Make welds quickly with these fast-melting electrodes.

Made of 85% pure nickel, these electrodes join cast iron to itself, and to mild steel and stainless steel.

Increase the wear resistance of your base metal, or restore a worn-down surface with these electrodes.