A micrometer handle ensures accurate, repeatable positioning along a single axis—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

A thumb screw locks the slide to prevent movement in systems where vibration is present.

Use these slides in a variety of manual-positioning applications for laboratory and production equipment as well as for positioning parts for drilling, fastening, assembly, and measuring.

Made with Frelon bearings, these slides have over four times the load capacity of standard positioning slides.

With a row of crossed-roller bearings on each side of the rail, these slides have over twice the load capacity of standard low-friction slides and are better for handling shock loads.

Good for use in pick-and-place applications, machine tool doors, and telescopic press arms, these rugged slides are designed to carry heavy loads.

These carriages and guide rails are steel.

Designed specifically for use on horizontal surfaces, the contact angle of the ball bearings on the rail allows these carriages to last longer than other carriages.

A plastic cage surrounds the ball bearings and keeps them from colliding, so these carriages run for many cycles without needing maintenance.

Suitable for clean room use, these carriages and guide rails are made entirely of stainless steel.

With a wide base and low-profile design, these carriages and guide rails stabilize moment (twisting) and off-center loads better than other carriages and rails. They're good for use in areas where multiple carriages or rails won't fit.

Adapt most 15 mm guide rails to fit on T-slotted assemblies.

Run many cycles in tight spaces before replacing or re-greasing carriages.

Use these carriages and guide rails for light loads where precise movement is not required.

A handle on the side of the carriage locks the carriage in place.

These track roller carriages and guide rails are stainless steel for use in wet, corrosive environments.

Needle-roller bearings give these track roller carriages higher load capacities than other track roller carriages.

Combine with a T-slotted rail to add linear motion to your assembly.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

With fewer moving parts and no need for lubrication, sleeve bearing carriages perform better in dusty and wet environments than ball and roller bearing carriages. They're also better at handling impact and vibration.

With a wide base, these sleeve bearing carriages stabilize moment (twisting) and off-center loads better than standard carriages. Use in areas where multiple carriages or rails won't fit.

For applications with low clearance, these carriages protrude less than 5 mm above their rails.

The square profile prevents loads from twisting and rotating.

Mate with a T-slotted rail to add linear motion to your assembly.

With an included controller and an integrated stepper motor, these slides are a complete precision motion control system.

Move loads with consistent, repeatable push-pull motion.

Accurately position a load by combining these actuators with a stepper motor, driver, and controller.

Modify the stroke length on these air slides to meet changing application requirements—slides have adjustable shaft collars on the guide rods that you can move to fine-tune the stroke length.

Take your Universal Robots arm to new heights—these bases move up and down to extend your robot’s vertical reach for high and low stacking jobs.

Keep a material certificate on hand for compliance and quality assurance needs. Certificates include a traceable lot number and material test report. These hollow shafts reduce system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

With 2" of each end softened, it's easier to machine a custom end for mounting. The rest of the shaft is case-hardened, which increases hardness and wear resistance on the surface of the shaft while allowing the center to remain soft for absorbing stresses caused by shifting loads.

Mount these externally threaded shafts into tapped holes rather than using a shaft support, or attach a hex nut, shaft collar, or other threaded accessory.

Lighter than solid shafts, hollow shafts reduce your total system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

A shoulder near the end of the shaft allows for easy positioning of housings, shaft supports, and collars.

With two bearings mounted in one housing, these sleeve bearings can handle heavier loads than standard mounted linear sleeve bearings.

Float bearings on air for precise, frictionless movement. Unlike traditional bearings that can wear your shaft down, these bearings are suspended using pressurized air for linear and rotary motion.

Use the adjustment screw in the housing to tighten or loosen the snugness (also known as preload) of the bearing to your shaft.

Choose ball bearings for debris-free environments and when speed is a necessity. They operate with less friction than sleeve bearings, so you can run them at higher speeds.

Virtually maintenance free, these bearings have slippery, chemical-resistant liners that don't require added lubrication.

The shell, housing, and balls of these bearings are stainless steel for excellent corrosion resistance.

A ceramic coating makes high speeds as well as rapid acceleration and deceleration possible.

A ceramic coating makes high speeds as well as rapid acceleration and deceleration possible.

Mount these bearings on a support rail shaft for applications requiring maximum rigidity.

With two bearings mounted in one housing, these sleeve bearings withstand heavy loads. Use them on round support rail shafts for applications that require maximum rigidity.

Slide up to two linear ball or sleeve bearings into these housings and secure them with the included internal retaining rings.

These bearings have a ceramic liner to help them achieve high speeds as well as rapid acceleration and deceleration.

Sleeve bearings outperform ball bearings in dirty environments. Use them for low speed applications.

Ball bearings create less friction than sleeve bearings, so they require less force to operate.