Designed for use in 1/4" or 1/2" dia. through holes.

These locks have a spring-wire cam that slips under a receiving catch on a cabinet body to create tension and hold cabinet doors and drawers closed.

With a finger-grip knob, these latches fit where latches with handles won't.

These latches have a spring-wire cam that slips under a receiving catch on a cabinet body to create tension and hold cabinet doors and drawers closed.

With an extra long shaft, these latches are good for use with thick, heavy doors, such as those found on trucks and large cabinets.

A large handle makes gripping these latches easier than other lift-and-drop barrel slide-bolt latches.

Also known as cane bolts, these latches have the added height that's needed to bridge large vertical gaps. Install them at the top or bottom of swinging doors and gates to hold them in an open or closed position.

Bolts are spring-loaded to stay latched until you activate the pull.

The strike has angled ends so these latches can accept their bolt even when doors become misaligned.

These padlockable latches are reversible for right- and left-hand mounting.

Slide the bolt and drop the knob into the notch to hold, then secure with a padlock.

Choose these locks if you need several locks that open with the same key.

These strikes fit most deadbolt-style locks.

These latches reach around outside corners to draw two surfaces together—use them to secure cases, toolboxes, and other containers.

A safety catch prevents accidental opening.

To prevent accidental opening, these latches have a safety catch.

An integrated slide bolt extends into the strike plate to resist pull and vibration from side-to-side, front-to-back, and up-and-down forces.

No need for a strike plate, these latches hook into a lip or notch.

Adjust the latching distance for a tight fit over gasketing and to compensate for misalignment.

These latches hook into a lip or notch and have an adjustable latching distance to compensate for gasketing and misalignment.

Each latch comes with a variety of strike plates for different mounting options.

Draw lightweight surfaces together with these latches.

With a spring-loaded handle, these hold tighter than other turn-to-open draw latches and compensate for slight misalignment.

These latches snap in place to eliminate rattling and hold access doors, screens, windows, and panels.

Secure surfaces together with these padlockable latches; built-in springs withstand vibration better than other latches.

Lift and turn the handle 180° to open and close these latches. Add a padlock to secure.

No need for a strike plate, these latches hook into a lip or notch.

Open several draw locks with the same key.

Mount these hasps around complex curves, angles, and corners that other corner hasps can't reach.

Mount these padlockable eyes to the front of a door and door frame.

Choose this hasp if you need several hasps that open with the same key.

Also known as bullet catches, these latches have a spring-loaded ball that grabs and holds the strike plate to keep doors shut.

There's no need for a mating strike plate for these latches—their spring-loaded arm snaps to engage when closing the door.

To prevent doors from slamming, these latches are hydraulic.

Close and open these roller latches with a push—there's no need for a handle.

For use on spray booths and drying ovens, these latches automatically open when the internal pressure of the enclosure reaches a set level.

Also known as paddle locks, these are often used on electrical panels, cabinets, and lockers.

A paddle handle activates the top and bottom spring-loaded latching points to secure large cabinet doors.

Use these latches alone for single-point latching, or add latch kits for more holding power.

Choose these L-handle locks if you need several that open with the same key.

The ring handle is recessed to stay out of the way when not in use. Latches arrive ready for single-point latching. For more holding power, add a latch kit for two-point latching, or add two latch kits for three-point latching.

Side, top, and bottom latching points secure large, heavy doors that are subject to strenuous use, such as those on trucks and large access doors.

To prevent accidental unlatching due to vibration, there's a bushing in the eye.

Designed to stand up to heavy use, these latches are often seen on refrigerators and truck doors.

This lock has a latch bolt to secure doors in the closed position.

Close the locker door and turn the dial to lock.

Choose these locks if you need locks that each open with a different key and also open with a master key.

These locking bars have hinges and swing out of the way for easy access to cabinet drawers.

Choose these locking bars if you need bars that each open with a different key.

For security, choose a combination from over 2,000 possible five-number combinations.

Spring tension holds screens in position.

With a smaller overall length, these lockout hasps fit in tighter spaces than other lockout hasps yet still hold a similar number of locks.

The overlapping hasp interlocks when closed for added security.

The fold-over closing design hinders prying, while a slot instead of holes makes it easy to install multiple padlocks.

Secure circuit breaker switches that don’t have a hole for a padlock.

In addition to a hasp that interlocks when closed, lockout has an adapter to lock out a valve and a chain that attaches to equipment so it won't get lost.

Lock out a machine with fewer padlocks when a team is working.

Lock out the on/off or emergency-stop buttons on machinery to prevent accidental or unauthorized startups, such as during maintenance.

Secure large bundles such as lumber, cardboard, and wire coils.

These inserts allow you to connect drawbar couplers to a receiver.

For an easy connection, push the trailer-mounted ring into the vehicle-mounted jaw of these couplers, and a spring-loaded lever automatically secures the ring for towing.

Floor locks bolt or weld to the underside of your equipment and have a spring-loaded base with a nonskid floor pad to keep equipment stationary.

These kits fit most hooks with a drilled pinhole.