Accommodate ties in any direction with these rings that swivel all the way around.

These rings mount flush and fold down when not in use to eliminate obstructions.

The ring pivots 180° to secure loads in various directions. Also known as lashing rings.

Adhesive on the back holds these rings in place.

Use these guides to position a rope.

Sew webbing onto these plates for a permanent anchor point or run webbing through to use them as guides.

Mount threaded accessories onto track.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

Compared to metal loop clamps, plastic loop clamps reduce wear on soft materials, such as tubing and cable. Clamps are nonconductive and noncorrosive.

Tighten the bolt for an exact fit around material. Clamps secure vertical pipes in sanitation drain applications and prevent them from coming in contact with the mounting surface.

Anchor these ringbolts where you need them, then remove the ring when not in use. Once installed, the mounting bolt stays in place. Insert the ring by threading into the mounting bolt; remove by unthreading it.

Temporarily mount routing rings and other threaded components to steel and iron surfaces.

Stick these ties to any smooth, clean surface.

Attach with a screw or other fastener.

Often used as tamper seals and in tagging applications, these ties create a consistent loop size every time.

Reduce gaps between the cable tie and bundle—these ties have a smooth body that allows them to adjust to the exact size of the material.

Three lenses bonded together offer sharp magnification without distortion.

Use this loupe to magnify and measure in one operation. Turn the eyepiece until you reach the magnification you need.

Magnify and measure in one operation.

An extra-wide lens that’s curved on the viewing side ensures edge-to-edge clarity.

Also known as Hastings Triplet magnifiers, these have three lenses bonded together for distortion-free images.

For use around sensitive electronic equipment.

Clip these magnifiers onto the frame of your eyeglasses for viewing fine details.

Designed for those who don't wear glasses.

Save time when attaching rope to tie downs and hooks.

A lighter and more flexible alternative to wire rope lanyards.

A clamp and thimble in one convenient fitting simplifies installation while providing support and fray protection to the wire rope loop. Use a torque wrench to tighten the clamp.

These clamps have a forged fabrication and are reliable in critical applications. They are not for making slings. These must be oriented with the saddle on the long (live) end and U-bolt on the short (dead) end. They’re also known as wire rope clips.

Use in noncritical applications, such as fencing, where the strength of a forged clamp is not required. Install clamps so the saddle is on the long (live) end and the U-bolt is on the short (dead) end. They’re also known as wire rope clips.

Also known as Type 5 and endless slings, these slings last longer than other web slings with eyes because they can be rotated to change the load-bearing point.

Increase the life of slings by positioning these protectors over areas prone to wear.

Securely hook these slings to a load that has lifting eyes.

These slings are more abrasion and cut resistant than web and round slings, yet lighter in weight than mesh and chain slings.

Latching hooks allow you to quickly release a load.

Grab hooks can securely hold onto a single link of chain to shorten a leg or create loops.

Similar to a finger trap, the loop adjusts freely when loose and holds tight when tension is applied.

Made of galvanized steel mesh to be more cut and abrasion resistant than web or round slings, yet maintain the flexibility to conform to a load.

These convenient squares and discs have an adhesive backing.

Cover surfaces up to 60" wide.

Both the hook and the loop meet MIL-A-A-55126.

Woven from Nomex and flexible stainless steel yarn, this hook and loop withstands temperatures up to 800° F.

A high-tack rubber adhesive on these hook and loop strips sets quickly in moist conditions.

A rigid vinyl backing gives this hook and loop stability.

Fasteners are cut into convenient rectangles and discs.

When two parallel strips are pressed together, these fasteners are about one-third to one-half the thickness of other snap-together fasteners.

Cut to wrap around any size bundle.

Also known as tether loops, these have a heat-shrink sleeve for gripping your tool and a D-ring for attaching to a tool lanyard.

These glasses protect your eyes from harmful infrared light while welding. Magnifying lenses enhance details up to 163% larger to make them easier to see.

Enhance details while protecting your eyes from dust and debris.