Connect these modular pumps to your air system and add a reservoir and solenoid valve to automate the flow of oil. Install or remove pumps as your lubrication needs change. Each pump has a separate flow adjustment; use a screwdriver to turn the flow-adjustment screw.

Pumps with spray nozzle provide a broader dispensing pattern. Nozzle bends and stays in position.

Note: For proper operation, pumps require a three-way solenoid valve (sold separately). The solenoid can be controlled by a timer or PLC (programmable logic controller).

For technical drawings and 3-D models, click on a part number.

Ready to connect to your air system, these complete systems include a timer and a reservoir. Turn the dials to set the cycle interval. Each pump has a separate flow adjustment; use a screwdriver to turn the flow-adjustment screw. Pumps and their components come mounted on a panel.

For technical drawings and 3-D models, click on a part number.

Use these valves with manual and electric pumps to dispense different amounts of oil from multiple lubrication points. They have a check valve to prevent backward flow. To connect to tubing, use a compression nut and sleeve (sold separately).

Flow rate trade number indicates the relative amount of oil each valve delivers. For each increase in trade size, the amount of oil delivered approximately doubles. For example, 0 delivers twice the amount of oil that 00 delivers. In a system with two lubrication points, the lubrication point connected to 0 will receive 2/3 of the oil dispensed, and the lubrication point connected to 00 will receive 1/3 of the oil dispensed. In general, valves with lower relative flow rates are better for cycling systems; valves with higher relative flow rates are better for continuous recirculation systems.

Dispense a fixed amount of oil by pumping the handle. To control flow to multiple lubrication points, use metering valves (sold separately).

Vertical pump dispenses oil when you pull the handle. Horizontal pumps dispense oil when you release the handle.

With a maximum flow of 0.005 oz. per cycle, these pumps deliver small, precise amounts of oil. Turn the dials to set the cycle interval. Each pump has a separate flow adjustment; use retaining ring pliers to turn the flow-adjustment nut. Pumps and their components come mounted on a panel.

For technical drawings and 3-D models, click on a part number.

Set the cycle interval as well as the dispensing duration. This pump has a maximum flow of 0.1 oz. per second. It has a low-level switch that triggers an audible alarm and can be wired to additional, external alarms.

Use metering valves (sold separately) to adjust the flow of oil to multiple lubrication points.

Choose from pumps that dispense with a set interval. Turn the dial to adjust the flow from 0.1 oz. to 0.2 oz. per cycle. Pumps have a low-level switch that triggers an audible alarm and can be wired to additional, external alarms.

Use metering valves (sold separately) to adjust the flow of oil to multiple lubrication points.

Connect these dispensing stations to your bulk oil container to easily fill hand-held dispensers. They include one faucet and can fit up to three, so you can access different types of oil at a single centralized point.

Stations with a meter measure oil as it's dispensed.

Use the keypad to select from six dispensing durations: 15 days, 1 month, 2 months, 3 months, 6 months, and 12 months.

Battery and grease packs (sold separately) must be installed and replaced at the same time for proper operation.

Connect a manifold (sold separately) to lubricate multiple points. Manifolds with mounting kit include connectors, adapters, tubing, and mounting hardware—all the components required to set up lubrication to multiple points.

Connect these modular pumps to your air system and add a solenoid valve to automate the flow of grease. Install or remove pumps as your lubrication needs change. Mounting holes are drilled through the pump's body. Each pump has a separate flow adjustment; use a screwdriver to turn the flow-adjustment screw.

Note: For proper operation, pumps require a three-port solenoid valve (sold separately). The solenoid can be controlled by a timer or PLC (programmable logic controller).

For technical drawings and 3-D models, click on a part number.