The hex shape achieves the best possible grip on hex fasteners to prevent rounding their points.

With more than double the clearance of standard sockets, these sockets access nuts on extra-long bolts.

Pivot the head to access fasteners from an angle.

Slide the open side of these sockets over a tube or hose to adjust a nut that’s already installed.

Pair these sockets with a bolt-through ratchet wrench to reach nuts at the bottom of a long threaded rod or bolt which can pass through the socket and the head of the wrench.

With a plastic insert, these sockets firmly grip hex nuts and bolts without rounding them or scratching highly polished finishes.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet IEC 60900.

For easy tightening and loosening, these sockets have pins that grip the slotted sides on bearing nuts.

Quickly position these sockets on square and external 8-point fasteners.

These sockets fit the nuts found on water and gas valves.

Turn multiple shapes and sizes of fasteners with a single socket.

Extra-long bits allow access to hard-to-reach fasteners.

When vertical space is tight or you need an extra twist on your socket, use these dual drive hex bit sockets. They work with a standard square drive tool and a box or open end wrench.

Extra-long bits allow access to hard-to-reach fasteners.

The short Phillips bit on these sockets fits in spaces that screwdrivers can’t and where height clearance is limited.

These sockets are also known as pin-in-Torx bits.

These sockets are also known as pin-in-hex or pin-in-socket bits.

An opening at the tip of these sockets fits around the security pin, allowing you to drive tamper-resistant Torx Plus screws.

Reach nuts obstructed by a fluid line or other barrier with these wrench heads.

A rubber insert grips the plug to prevent damage.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the wrench.

Built for tough industrial conditions, these wrenches have a gasket that seals lubrication in and keeps dirt, dust, and moisture out to protect the ratchet mechanism. When it’s time to release the socket, just push the button on the back of the wrench head.

The shaft on these wrenches extends and locks.

Pair these wrenches with a bolt-through socket to reach nuts at the bottom of a long threaded rod or bolt which can pass through the head of the wrench.

Also known as a construction or spud handle, wrenches use the pointed end to align bolt holes.

Customize the handle angle to reach over obstructions or fold the handle away to create a palm ratchet.

The convenience of quick socket changes combined with the versatility of a folding wrench.

Pivot the head on these wrenches to access fasteners in tight spots.

Reach over obstructions and access fasteners in tight spots—even in dirty and dusty areas. To protect the ratcheting mechanism, these wrenches have a gasket that seals lubrication in and keeps debris out.

Pivot the head and extend the handle—these wrenches adapt to reach fasteners in challenging spots. When it’s time to release the socket, just push the button on the back of the head.

Access fasteners in tight spots by pivoting the head to an optimal angle. These nonratcheting wrench handles are also known as breaker bars—they’re long enough for you to get the leverage needed to break stuck fasteners free.

Extend the shaft for additional length.

Loosen stubborn fasteners while working up high—these wrench handles clip to a carabiner or lanyard (not included) to prevent drops.

Turn sockets from above when there's not room to swing a standard wrench handle.

A soft, contoured grip gives you a secure, comfortable hold. Use these handles to tighten and loosen sockets from above when there isn’t room to swing a standard wrench.

Set the desired torque and the wrench indicates when it's reached with an audible click and an impulse in the grip.

No need to pull the socket off the tool—push a button to release.

Made of beryllium copper, these wrenches satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

These wrenches have an accuracy of ±2.0%.

Measure with an accuracy of ±2%.

A main pointer on the dial shows torque as it’s being applied and a memory pointer indicates the maximum torque reached.

Measure with an accuracy of ±7%.

Turn sockets from above when there's not room to swing a standard wrench handle.

Also known as impact drivers, use these tools with impact sockets to break frozen bolts and screws free. Strike with a hammer to tighten and loosen fasteners.

Loosen stubborn fasteners—these wrenches operate at full torque counterclockwise to break stuck bolts free.

Faster than manual ratchet wrenches, these ratchet wrenches run on air to turn fasteners quickly.

Use these wrenches with impact sockets only.

Attach your square-drive sockets to drills, powered screwdrivers, and other tools that accept a hex shank.

Attach your square-drive sockets to drills, powered screwdrivers, and other tools that accept a hex shank.

Extend your socket's reach.

Safely extend your reach in areas where you could accidentally come into contact with live circuits.

Reach a variety of spots with the confidence that your extension won’t disengage.

Bend these extensions to reach inconveniently located fasteners. These sets include multiple extension lengths, so you can find the right length to reach around obstructions.

Lock your socket into these extensions to prevent accidental disengagement.

Convert from one square drive size to another.

These adapters are insulated to protect against accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC 60900.

Already set to a specific torque limit, these adapters audibly click and release when you reach that setting to prevent overtightening.

Convert your socket into a flex socket to access fasteners from an angle.

Convert your socket into a flex socket without worrying about the adapter falling off.

Fit these adapters between a wrench and socket to enable finger tightening.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Pair the sockets in these sets with the bolt-through ratchet wrench to reach nuts at the bottom of a long threaded rod or bolt.

The sockets in these sets have a cutout and extra length so you can reach and twist nuts without having to disconnect your line.

Two spring-loaded balls inside these sockets firmly hold nuts and bolts in place as you turn them, including nonmagnetic fasteners like stainless steel screws.

Suitable for occasional maintenance work, these sets are imported.

Pivot the head to access fasteners from an angle.

Shaped and sized for compatibility with wheel bearing locknuts on trucks and trailers, the sockets in these sets make it easy to install and remove locknuts.

With squared lobes that won’t slip at high torque, all of the sockets in these sets are designed to fit on external Torx-Plus fasteners, often found on pickup trucks.

Grip the indentations around the outside of tri-groove fasteners.