For quick repairs, these epoxies begin to harden in 6 minutes or less.

With excellent resistance to corrosive chemicals and salt water, these epoxies work in tough conditions.

These machinable epoxies are mixed with metal so they can be used to repair cracks and threaded holes.

For invisible bond lines, these adhesives dry clear.

Bond most materials without the strong odor of other epoxy adhesives.

Fasten hard-to-bond plastics, such as polypropylene and polyethylene, with these epoxies.

No need to mix these acrylics—apply adhesive to one surface and activator to the other, then bring surfaces together to bond.

To keep these adhesives from squeezing out during clamping and give a consistent bond thickness, they're mixed with small glass beads.

With excellent shear strength, these acrylics form bonds at least 25% stronger than standard acrylic structural adhesives.

With high shear strength and peel strength, these form the strongest bonds of our urethane adhesives.

Also known as super glue, these adhesives bond quickly.

Fasten hard-to-bond plastics, such as polypropylene and polyethylene.

These adhesives withstand temperatures of 390° F or more.

In especially damp or humid environments, these adhesives keep their hold.

Form bonds in 5 seconds or less.

Make strong, instant bonds on a variety of materials—but not your skin.

These adhesives withstand temperatures up to 480° F.

Form bonds without the strong odor of other instant-bond adhesives.

Bond plastics, porous materials, or dirty surfaces.

These thick gels fill gaps up to 0.2" wide—the largest of any of our instant-bond adhesives.

These super glues are blended with rubber for better impact and moisture resistance than other instant-bond adhesives.

For easy positioning, these adhesives begin to harden only when exposed to light.

For flexible bonds that resist cracking, these adhesives stay pliable.

The 3M VHB adhesive on these rolls offers a strong hold that can replace rivets, spot welds, and other permanent fasteners.

Apply this glue like tape for a no-mess alternative to liquid adhesives, hot melts, and staples. Also known as adhesive transfer tape.

This putty-like glue cures into a pliable rubber. Use it to repair seals and cracks, or mold it into hooks and bumpers.

Also known as Gorilla Glue, this glue expands to form stronger bonds than other glue.

Apply these adhesives on two surfaces, air dry, and then bring together to bond.

For easy positioning, this adhesive remains tacky for hours. Once items are in place, apply pressure to create a permanent bond.

An alternative to solder, these flexible, silver-filled adhesives accommodate joint movement. Use them to bond electrical components and repair circuits.

This glue remains flexible after curing to accommodate joint movement.

To simultaneously mix and dispense two-part adhesives, attach these mixer nozzles to a dual cartridge.

Fill gaps up to 0.01" to secure unthreaded cylindrical metal parts such as shafts, bearings, and press-fit assemblies.

Even on oily surfaces, these retaining compounds keep their hold.

To speed cure time on coated fasteners, aluminum, stainless steel, or titanium, apply these primers before using threadlocker or retaining compound. They also work with no-mix acrylic adhesives.

Use these threadlockers on fasteners that require occasional fine-tuning, such as set screws.

Apply these threadlockers on fasteners that are already installed—their thin consistency allows them to flow into small gaps.

Coat fasteners ahead of time and store until ready to use. Upon installation, tiny capsules rupture to release the threadlocker.

These threadlockers meet NSF/ANSI 61 for drinking water.

Keep threaded fasteners from loosening at temperatures up to 450° F.

Wrap this no-mess tape around threaded fasteners up to 30 days before installation.

Paste threadlockers are easy to apply and won't drip, even from overhead fasteners.

This thick paste withstands temperatures up to 650 °F.

These structural sealants combine the mechanical strength of an adhesive with excellent sealing properties and high flexibility.

Also known as neutral cure, this sealant won't discolor copper, brass, plastic, and concrete.

With chemical and metal additives that are picked up by X-ray machines and metal detectors, these sealants are designed to help you comply with Hazard Analysis and Critical Control Point (HACCP) programs in food-processing facilities.

Made from silicone, these sealants are RTV (room-temperature vulcanizing).

Resistant to mold and mildew, these sealants are well suited to high-humidity environments.

Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Also known as neutral-cure sealants, these won't discolor copper, brass, and concrete.

Clear enough to read through, this UV-resistant sealant allows optimal light transmission for use with solar cells and fiber optics.

Apply these sealants in cold temperatures, on wet surfaces, and even through running water.

Also known as thumb-grade caulk, this forms a non-hardening, moisture-resistant seal that remains pliable.

These non-sagging sealants will not drip while hardening on vertical and overhead surfaces.

Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.