A double hinge provides high cutting force with low gripping pressure. These cutters are also known as aviation snips.

Keep your hand away from the material being cut.

Prevent waste from flying up as you work. A double blade makes two cuts, creating a 7/64" wide strip that peels back leaving little distortion and smooth edges.

This cutter has two blades that cut a 13/64" wide strip—peel it back for smooth edges with little distortion.

These cutters make straight cuts and curves.

Also known as bulldog snips, these have long handles and short blades for cutting heavy material in any direction.

Replace blades as they wear. These cutters are also known as tinners' snips.

Made from aluminum bronze, the blade and handle on these cutters inhibit sparking and are FM approved. Use them for straight cuts.

Make cuts in metal up to 1/32" thick with these compact cutters.

Blades are heat treated then sharpened for increased performance and durability.

Also known as bulldog snips, these have long handles and short blades for cutting heavy material in any direction.

Make round, square, and irregular-shaped holes with this punch-style hole cutter.

Cut up to 1" deep V-shaped notches in sheet metal.

Use to cut patterns in flat material with minimal material loss and less effort compared to manual cutters.

A double blade creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

Punch small pieces out of material to create an almost burr-free cut with no material distortion.

Minimize material loss and edge distortion with these scissor-like cutters that cut metal up to 1/64" thick.+

These nibblers punch small pieces out of material to create an almost burr-free cut with no material distortion.

Also known a scissor-blade shears, the bottom blade remains stationary while the upper blade moves up and down to cut metal up to 1/64" thick with minimal material loss and edge distortion.

Also known as slotting shears, these cutters have a double blade that creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

Turn your portable drill into a punch cutter for cutting curved and straight shapes in flat and corrugated sheet metal and plastic.

Make straight, clean cuts in thick sheet metal.

A 12" long blade makes long, straight cuts in thin metals and flexible materials. Not for use on phenolic or other rigid materials.

This large-capacity cutter has a 25" blade for long, straight cuts.

Turn your workpiece while cutting to create curves and complex shapes.

Combine the cutting base and a corner punch to make rounded corners in sheet metal.

Notch, cut, and pierce a variety of materials including metal, plastic, and vinyl.

Make straight cuts in sheets. These cutters are foot operated so your hands are free to position the material.

Mount this cutter to the floor and use it to cut through steel angle iron up to 2"×2"×1/4".

Leave clean cut edges in a variety of pliable materials.

These air-powered cutters include a semi-square blade for no-fray cuts.

The small size and spring-loaded jaw lets you make quick cuts with one hand.

Handle is angled 30° to keep work in sight and hands clear of the work surface. Blades are flat on one side for close-to-the-surface cuts.

Cut hard bolts and up to Grade 70 chain with reinforced blades that stay aligned during repeat cuts.

Cut medium steel chain and hard steel bolts, rods, screws, rivets, nails, bars, wire, and rebar.

With a short-nosed jaw, these cutters force the material being cut deeper into the jaw for maximum leverage. The short jaw also allows you to cut one side of a chain link or padlock hasp without hitting the other side.

Blades are flat on one side for close-to-the-surface cuts.

Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Make repeated cuts in hard materials with cutters that mount for stability and provides extra leverage.

Slice through bolts and chain with low effort.

Cutters have double hinge that provides high cutting force with low gripping pressure.

Keep your hands in a comfortable position so you can apply more force for cutting.

Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

A small grip enables one-handed cutting.

Minimize material distortion while cutting steel and stainless steel wire rope.

With a quick hammer blow, these cutters make cuts without squeezing or flattening wire.

Use the lever to make one-handed cuts with minimal material distortion. Cutter mounts to a workbench for extra stability and ease of use for repeated cuts.

These manually operated cutters make a clean cut with just a few pumps of the handle.

Make clean cuts on threaded rod with the pull of a trigger.

An alternative to hacksaws and bandsaws, these cutters use leverage to cut rods cleanly in a single stroke.

Cut rods and bolts while leaving their threads intact.

Hydraulic-powered jaws cut bolts, wire rope, rods, and electrical cable with low effort and minimal material distortion.

Plastic-cushioned grips make these cutters easy to hold during repeated cuts.

Cut hard steel wire, nails, and small rivets close to the surface with the wide, flat jaws on these cutters.

Sharpen or replace the jaws as they wear. These cutters have a double hinge that provides high cutting force with low gripping pressure.

A double hinge provides high cutting force with low gripping pressure.

Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Also known as nippers, these cutters have wide, flat jaws that cut steel wire and bolts close to the surface.

Made of beryllium copper that is FM approved, these cutters satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Unlike standard tube cutters, which cut from the outside, these cutters slide into tube ends to cut and vent from inside.

Good for high-volume cutting and trimming.

Pull the lever on these cutters to make smooth cuts in steel and aluminum DIN rail without leaving a bur.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts in aluminum, iron, stainless steel, and steel.

Made of premium grade abrasives, these wheels are strong and thick for making notches in aluminum, iron, stainless steel, and steel.

Switch between cutting and deburring aluminum, iron, stainless steel, and steel without the need to change your wheel.

Make fast, burr-free cuts in stainless steel with these ceramic and zirconia alumina wheels.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts.

Prevent corrosion and discoloration on stainless steel—these wheels contain less than 0.1% iron, chloride, and sulfur contaminants.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts.

Made of premium grade of abrasives, these wheels are strong and thick for making notches in stainless steel.

Made of a combination of ceramic alumina and zirconia alumina, these wheels last up to ten times longer than standard cutoff wheels when cutting hard metal such as Inconel, Hastelloy, and tool steel.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts.

Run these high-density aluminum oxide wheels at higher speeds than standard cutoff wheels to make quick cuts in aluminum, iron, stainless steel, and steel.

Two layers of fiberglass mesh reinforcement give these wheels at least three times the life of standard cutoff wheels when cutting metal such as aluminum, iron, stainless steel, and steel.

These high-density ceramic oxide wheels have two layers of fiberglass mesh reinforcement and last up to twice as long as long-life cutoff wheels when cutting aluminum, iron, stainless steel, and steel.

For quick cuts in stainless steel, run these high-density zirconia alumina wheels at a higher rpm than standard cutoff wheels.

Use these clog-resistant zirconia alumina wheels to make quick cuts in soft metal such as aluminum, brass, and copper.

The combination of ceramic alumina and zirconia alumina in these wheels lasts up to ten times longer than aluminum oxide when cutting hard metal such as Inconel, Hastelloy, and tool steel.

An extra-fine layer of fiberglass mesh reinforcement allows these wheels to make smoother cuts than standard bench-grinder cutoff wheels when cutting metal such as aluminum, iron, stainless steel, and steel.

Two layers of fiberglass mesh reinforcement give these fast-cutting, zirconia alumina wheels at least three times the life of standard cutoff wheels when aluminum, iron, stainless steel, and steel.

These wheels are designed to cut stainless steel. They are reinforced with a layer fiberglass mesh.

These non-reinforced aluminum oxide wheels create the nearly polished finish required for testing metal.

These wheels are thinner than standard bench-top cutoff saw wheels, so they cut through aluminum, iron, stainless steel, and steel more quickly.

Use these clog-resistant wheels to make quick cuts in soft metal such as aluminum, brass, and copper.

Make fast, burr-free cuts in stainless steel with these premium aluminum oxide wheels.

Designed to cut sheet metal.

Use these wheels to cut through metal such as iron and steel. They are reinforced with a layer of fiberglass mesh.