A double hinge provides high cutting force with low gripping pressure. These cutters are also known as aviation snips.

Keep your hand away from the material being cut.

Prevent waste from flying up as you work. A double blade makes two cuts, creating a 7/64" wide strip that peels back leaving little distortion and smooth edges.

This cutter has two blades that cut a 13/64" wide strip—peel it back for smooth edges with little distortion.

These cutters make straight cuts and curves.

Replace blades as they wear. These cutters are also known as tinners' snips.

Also known as bulldog snips, these have long handles and short blades for cutting heavy material in any direction.

Made from aluminum bronze, the blade and handle on these cutters inhibit sparking and are FM approved. Use them for straight cuts.

Blades are heat treated then sharpened for increased performance and durability.

Also known as bulldog snips, these have long handles and short blades for cutting heavy material in any direction.

Make cuts in metal up to 1/32" thick with these compact cutters.

Make round, square, and irregular-shaped holes with this punch-style hole cutter.

Cut up to 1" deep V-shaped notches in sheet metal.

A double blade creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

Use to cut patterns in flat material with minimal material loss and less effort compared to manual cutters.

Punch small pieces out of material to create an almost burr-free cut with no material distortion.

Minimize material loss and edge distortion with these scissor-like cutters that cut metal up to 1/64" thick.+

Turn your portable drill into a punch cutter for cutting curved and straight shapes in flat and corrugated sheet metal and plastic.

These nibblers punch small pieces out of material to create an almost burr-free cut with no material distortion.

Also known as slotting shears, these cutters have a double blade that creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

Also known a scissor-blade shears, the bottom blade remains stationary while the upper blade moves up and down to cut metal up to 1/64" thick with minimal material loss and edge distortion.

Make straight, clean cuts in thick sheet metal.

A 12" long blade makes long, straight cuts in thin metals and flexible materials. Not for use on phenolic or other rigid materials.

This large-capacity cutter has a 25" blade for long, straight cuts.

Combine the cutting base and a corner punch to make rounded corners in sheet metal.

Turn your workpiece while cutting to create curves and complex shapes.

Notch, cut, and pierce a variety of materials including metal, plastic, and vinyl.

Make straight cuts in sheets. These cutters are foot operated so your hands are free to position the material.

Leave clean cut edges in a variety of pliable materials.

These air-powered cutters include a semi-square blade for no-fray cuts.

Mount this cutter to the floor and use it to cut through steel angle iron up to 2"×2"×1/4".

Cutters have double hinge that provides high cutting force with low gripping pressure.

Also known as nippers, these cutters have wide, flat jaws that cut steel wire and bolts close to the surface.

Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Minimize material distortion while cutting steel and stainless steel wire rope.

Keep your hands in a comfortable position so you can apply more force for cutting.

A small grip enables one-handed cutting.

Cut medium steel chain and hard steel bolts, rods, screws, rivets, nails, bars, wire, and rebar.

With a short-nosed jaw, these cutters force the material being cut deeper into the jaw for maximum leverage. The short jaw also allows you to cut one side of a chain link or padlock hasp without hitting the other side.

Blades are flat on one side for close-to-the-surface cuts.

Cut hard bolts and up to Grade 70 chain with reinforced blades that stay aligned during repeat cuts.

Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

The small size and spring-loaded jaw lets you make quick cuts with one hand.

Make repeated cuts in hard materials with cutters that mount for stability and provides extra leverage.

Slice through bolts and chain with low effort.

Handle is angled 30° to keep work in sight and hands clear of the work surface. Blades are flat on one side for close-to-the-surface cuts.

Make clean cuts on threaded rod with the pull of a trigger.

Cut rods and bolts while leaving their threads intact.

An alternative to hacksaws and bandsaws, these cutters use leverage to cut rods cleanly in a single stroke.

Hydraulic-powered jaws cut bolts, wire rope, rods, and electrical cable with low effort and minimal material distortion.

Pull the lever on these cutters to make smooth cuts in steel and aluminum DIN rail without leaving a bur.

Good for high-volume cutting and trimming.

Push the button to cut aluminum and copper power and communication cable.

For extra leverage to cut through Kevlar, metal, and plastics, these scissors have long handles and short blades.

After each cut, the jaws spring open to make continuous cutting easy.

Longer handles and shorter blades give you more leverage than other scissors to cut tough materials such as leather, rope, and thick cardboard.

Cut keyways at the edges of existing holes. Also known as a keyway nibbler.

Save space in your shop by cutting, bending, and curving sheet metal with a single machine. Also known as shear brake rolls.

A long handle gives you the leverage to quickly bend metal.

Also known as 40-ton metalworkers, these hydraulic machines handle a variety of forming tasks including pressing, punching, notching, and shearing.

Two-handed strap cutters give you more leverage than one-handed strap cutters.

Slip strapping into the slot and rotate the handle to snap the strap.

Keep one hand free while cutting and trimming strapping.