Press these grommets into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

A rolled rim provides added grip while the elongated neck and teeth on the washer, also known as a spur washer, add reinforcement and reduce rotation so you can use these grommets in thick materials such as canvas. Press the grommets into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

The sharp neck on these grommets cuts the material as you press them into place, eliminating the need for a cutting punch. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

Cushioning on the top provides added protection from impact. This nylon-coated stainless steel trim combines strength with flexibility for a snug hold. It can also protect wire, cable, and hose.

Made of aluminum or stainless steel, this trim withstands heavy impact for maximum surface protection. It's often used on panels, boards, signs, and mirrors to protect the edges.

Suitable for use in applications where cords are underwater—these grips are rated IP68 for protection from prolonged submersion.

Keep cords from coming loose and seal water out of enclosures in extremely cold labs and storage areas. Thanks to their plastic bushing and rubber O-ring, these grips withstand temperatures as low as -75° F.

These grips are the most corrosion resistant of any of our submersible metal cord grips.

With an oval bushing hole, these lightweight grips secure flat building cable, such as Romex and Festoon cable, in wet areas. All offer strain relief to extend cable life.

Route cords at a 45° angle when space is tight around enclosures and panels in wet and oily environments.

These cord grips are lightweight yet durable.

Secure and seal electrical cords entering knockouts at a 45° angle.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

Able to stand up to rust better than steel grips, these 300 series stainless steel grips secure electrical cables in corrosive environments.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

Secure cords in wet and industrial environments with little room—these grips curve 45° to relieve bending stress.

The mesh offers a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These grips meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection.

Modify these cord grips to get the right fit for your cord even when you don't know the exact diameter.

Install additional cables without swapping cord grips by pushing them through the thin, flexible seals on these grips, which have a sanitary design suitable for food-processing and pharmaceutical plants.

These female snap halves create the finished button-look of a snap. Pair them with male snap halves to create a complete snap.

Male and female snaps are included to create complete snaps.

Once installed, these fasteners provide a male snap half on both sides of your fabric. Create a complete snap by joining each male side with a female snap half for a finished look on assembled layers of fabric.

Everything you need to fasten a fabric snap to a solid surface.

Kits include a hand punch tool with die and six complete snaps with tapping screw studs.

The drilling screw stud drills its own hole.

Create an eyelet for turn-button fastener bases.

Snap these nuts into square holes in thin materials.

These rounded head screws have a nut that clips onto the edge of a thin panel, allowing you to mount the screw near edges. A quarter-turn locks and releases access panels, doors, and covers.

Press these rounded head nuts into the backside of a panel in applications where you have access to both sides of the panel. A quarter-turn locks and releases access panels, doors, and covers.

Press these wing head nuts into a closed-end hole or thick panel in applications where the back of the panel is inaccessible. A quarter-turn locks and releases access panels, doors, and covers.

Rivet these wing head nuts into thin panels for a flush fit. They can be mounted without space between panels. A quarter-turn locks and releases access panels, doors, and covers.