Suitable for food-processing areas, these one-piece knobs have no joints to collect dirt or debris. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery. Mount them into a threaded hole.

Knobs have left-hand threads; they're used in applications where counterclockwise motion can loosen common right-hand threads. Mount them into a threaded hole to position, tighten, and hold fixtures, equipment, and machinery.

A rubber coating provides a comfortable grip to position, tighten, and hold fixtures, equipment, and machinery. Install these knobs on a threaded stud.

Designed for sanitary environments, these knobs are commonly used in pharmaceutical and food-processing facilities. Install them on threaded studs to position, tighten, and hold equipment.

Quick to install, position, and remove, these knobs have an angled hole that allows you to tilt the knob to slide it over threads, then straighten it to grip the threads and secure the knob. They provide a firm grip to position, tighten, and hold fixtures, equipment, and machinery.

A handle makes these knobs easy to turn. Tap custom threads or secure with a set screw to provide a firm grip to position, tighten, and hold fixtures, equipment, and machinery.

Mill specific holes or keyways in the hub to meet your specifications, or weld in place. These knobs provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

A handle makes these knobs easy to turn. Mill specific holes or keyways in the hub to meet your specifications, or weld in place. These knobs provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

Primarily used on spigot valves, slide these knobs over valves with a square stem and secure them in place with your fastener.

Control devices with round or D-shaped shafts and view settings at a glance with a pointer.

Often used on pallet and lift trucks, these knobs attach to steering wheels for one-hand operation.

Install these knobs on a threaded stud. Insert a bar between the arms and twist. The bar provides maximum leverage to tighten knobs securely.

These rugged steel handles provide lasting durability for applications involving frequent positioning, tightening, and holding adjustments. Lift the handle to rotate freely; then release the handle to engage and tighten. These handles are also known as clamping handles.

These rugged steel handles provide lasting durability for applications involving frequent positioning, tightening, and holding adjustments in areas with limited vertical space. Lift the handle to rotate freely; then release the handle to engage and tighten. These handles are also known as clamping handles.

Made of stainless steel with a nitrile mounting seal, these handles are suitable for food-processing applications involving frequent positioning, tightening, and holding adjustments. Lift the handle to rotate freely; then release the handle to engage and tighten. These handles are also known as clamping handles.

Also known as finger handles, these are less than 1" long. Use them as tiny grips on small hand wheels and cranks to operate machinery.

Attach a ball knob to one of these shafts to create custom handles for operating machinery.

Press fit one of these handles into a shaft, rod, or hand wheel to operate machinery.

Use these standard cam handles for most clamping applications. Push down on the handle and the head applies pressure to quickly draw two parts together for fast adjustments.

Add a pin, rod-end bolt, or other mounting hardware to build a custom assembly. Also known as double cams, these handles have a durable, extra-large handle for clamping on fixture bases, plates, and workpieces. For fast adjustments, push down on the handle and the head applies pressure to quickly draw two parts together.

Whether you're looking for a stopgap or permanent replacement, these valve handles adjust to fit a range of valve and faucet stem widths.

Connect ball swivels and damper linkages to an actuating motor to control ventilation dampers.

With a sanitary design, these threaded-hole knobs are often used to open and close doors and drawers on furniture, machines, and other equipment in pharmaceutical and food-processing facilities.

Mount these knobs in a cutout to keep them out of the way when not in use. Push the grip to extend, and push it again to recess. Use these knobs to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

With a mounting hole center-to-center distance of 1" or less, these are the smallest pull handles we offer. Thread screws through holes from the back of your surface into the handles to open and close tiny doors and drawers.

Suitable for use with food-processing equipment, these handles are made of FDA listed materials.

A rubber coating provides a comfortable grip. Cut the grip to the length you need before mounting. Fasten these handles directly to the front of your surface to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

For applications that require a large gripping area, these handles have a center-to-center distance of 12" or more. Fasten them directly to the front of your surface to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

Insert studs into holes in your surface and secure from the backside to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

When not in use, the spring in these handles keeps the folding grip flush with the mounting plate and prevents rattling. Fasten the handles directly to the front of your surface to open and close a variety of doors and drawers on chests, crates, furniture, machines, and equipment.

These handles provide a stronger connection than those attached with screws or nuts. Their grip folds out of the way when it's not in use. Use them to open and close a variety of doors and drawers on chests, crates, furniture, machines, and equipment.

Fasten these handles directly to the front of your surface. They fit into a cutout, so they are flush with the mounting surface. Their grip drops out of the way when you let go. Use them to open and close a variety of doors and drawers on chests, crates, furniture, machines, and equipment.

Detents keep these handles in the extended or folded position—they won't move until you reposition them. Insert studs into holes in your surface and secure from the backside to open and close a variety of doors and drawers on chests, crates, furniture, machines, and equipment.

Fasten these handles directly to the front of your surface to open and close a variety of doors and drawers on chests, crates, furniture, machines, and equipment. When not in use, the grip folds out of the way.

Thread screws through holes from the back of your surface into the handles to open and close a variety of doors and drawers, including those on furniture, machines, and equipment. The grip is offset from the mounting surface so there's room to fully grasp the handle.

Tap custom threads or drill a hole in the side of the hub to secure with a set screw. The spoked design allows a better grip around the rim than solid hand wheels to manually adjust valves, presses, and machine components.

Create custom threads or drill a hole in the side of the hub to secure with a set screw. Long shafts can pass through these hand wheels for mounting versatility. The wheels are solid, so they won't catch hands or material while manually adjusting valves, presses, and machine components.

An easy-to-read dial provides accurate settings for monitoring the number of wheel turns while manually adjusting valves, presses, and machine components.

Open and close almost any hand-wheel operated overhead valve from the floor. These wheels can also be used to operate hatches, skylights, and other overhead components.

Balanced weight distribution prevents unintentional handle movement, even in high-vibration applications. Mill specific holes or keyways in the hub to meet your specifications or weld in place. Often used on cross-slide tables, these crank handles provide leverage to maximize force for turning and tightening.

Square long shafts can pass through these handles for mounting versatility. Drill a hole in the side of the hub to secure with a set screw. These crank handles provide leverage to maximize force for turning and tightening. They are often used on cross-slide tables.

These metric thumb screws are made of chemical-resistant 18-8 stainless steel. They have a raised head that makes them easy to grip.

These metric thumb screws have a raised head that makes them easy to grip. A black-oxide finish provides corrosion resistance in dry environments.

Made from 18-8 stainless steel, these thumb screws are chemical resistant. They have a thin, knurled head for use in low-clearance applications.

These metric thumb screws are made of chemical-resistant 18-8 stainless steel. They have a thin, knurled head for use in low-clearance applications.

These metric thumb screws have a thin, knurled head for use in low-clearance applications. They have a black-oxide finish to resist corrosion in dry environments.

Stainless steel thumb screws have excellent corrosion resistance in most environments.

Brass thumb screws are corrosion resistant in wet environments and electrically conductive.

These slotted thumb screws are slim to fit in tight spaces.

Stainless steel thumb screws have excellent corrosion resistance in most environments.

These metric thumb screws have a large head that allows you to grip them with your entire hand for greater torque while tightening than standard knurled plastic-head thumb screws.

These metric thumb screws have a knurled head for a slip-resistant controlled adjustment.

Tighten these thumb screws by hand or with a hex key for more torque.

These metric thumb screws have arms that provide a flat surface to push your fingers against.

These metric thumb screws are made of chemical-resistant 18-8 stainless steel. Also known as dog- and pilot-point thumb screws, insert the point into a drilled hole or slot to hold items in place.

A wide tip provides more gripping power than standard swivel-tip thumb screws. To use, remove the tip, thread the screw through the hole, and attach the tip on the other side.

A large swivel angle allows these thumb screws to make better contact with angled and uneven surfaces than nonremovable swivel-tip thumb screws.

These steel thumb screws have a black-oxide finish to resist corrosion in dry environments.

Use an arbor press or similar pressure tool to install these spring plungers into a panel.

Lock the nose in the retracted position by pulling the knob and rotating it 90°.

In addition to lasting twice as long as standard door knobs, these are made entirely of corrosion-resistant materials to stand up to washdown and marine environments.

In addition to lasting twice as long as standard key-locking door knobs, these are made entirely of corrosion-resistant materials to stand up to washdown and marine environments.

In addition to lasting twice as long as button-locking door knobs, these are made entirely of corrosion-resistant materials to stand up to washdown and marine environments.

Hold crossbars in the open position so traffic can pass freely through doorways.

These latches have a spring-wire cam that slips under a receiving catch on a cabinet body to create tension and hold cabinet doors and drawers closed.

Secure these latches with a padlock.

Attach tool holders such as collet chucks and end mill holders to your CNC machine’s spindle.