Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.

With a thickness that's precision ground to a tight tolerance, these bars are sometimes called flat stock.

In addition to good corrosion resistance, the nickel coating provides better wear resistance than the zinc-galvanized coating.

A silver-filled resin coating on one side of these sheets protects from degradation caused by bacteria and fungi.

This UHSS (ultra high-strength steel) allows you to fabricate high-strength parts using thinner material than you could with other types of steel. It is formable, weldable, and more economical than alloy steel.

Even in low temperatures, A516 carbon steel resists breaking upon impact. Also known as pressure-vessel-quality (PVQ) steel, it is mostly used for boilers, storage tanks, and pressure vessels.

Stronger than low-carbon steel with equally good machinability, 1045 carbon steel is widely used for bolts, studs, and shafts.

Also known as flat stock, the thickness on these sheets and bars is held to a tight tolerance.

Because the thickness is oversized, you can finish these bars to your exact requirements.

The thickness is oversized for finishing to your exact requirements.

4130 alloy steel has a low carbon content that provides good weldability. It's often used for gears, fasteners, and structural applications.

Also known as weathering steel, this high-strength steel develops a thin layer of rust over time in outdoor environments that protects the inner steel from corrosion.

Also known as blue-tempered steel.

5160 alloy steel handles repeated cycles of stress without breaking just like spring steel. It’s often used to make flat springs.

Gray cast iron machines faster with less wear on cutting tools than most types of steel. It's often fabricated into gears, pulleys, and bushings.

The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

The thickness is oversized to allow for finishing to exact requirements.

An anodized coating bonds to the aluminum surface to improve wear and corrosion resistance.

6101 aluminum is chiefly used as a lightweight and economical alternative to copper in electrical applications, such as bus bars in switchboards and battery banks.

3003 aluminum stands up to outdoor use, as well as exposure to chemicals. It offers a good combination of strength, formability, and weldability. It's often used for storage tanks, heat exchangers, garage doors, and general sheet metal work.

One side of these sheets is painted in your choice of gloss color, while the other side is painted gloss white.

A honeycomb core is bonded between two aluminum sheets for rigidity.

Known for being one of the easiest types of aluminum to weld, 5052 is also recognized for its ability to resist salt water. It's widely used for the bodies of boats, buses, trucks, and trailers, as well as for chemical drums.

5086 aluminum is used on ships, oil rigs, tanks, and pressure vessels because of its excellent saltwater resistance and formability.

Stronger than other marine-grade aluminum, 5456 is often used for pressure vessels and storage tanks in saltwater environments.

Made of 1100-series aluminum which is 99% pure, this aluminum offers superior formability, corrosion resistance, and electrical conductivity. It's frequently fabricated into raceways, decorative trim, and other parts where strength and hardness are not required.

Also known as armor plate, these 5083 aluminum sheets are hardened to an H131 temper for increased strength and impact resistance over standard 5083 sheets.

MIC6 is cast from a high-strength 7000-series aluminum, then stress relieved to maintain dimensional stability during high-speed machining.

While 2024 aluminum was initially designed for structural components in aircraft, it's now widely used when a high strength-to-weight ratio is needed, such as for gears, shafts, and fasteners. It offers similar performance to 7075 aluminum, but it’s not as strong.

These sheets are clad in 1230 aluminum for an added layer of corrosion resistance.

Originally developed for aircraft frames, uses for 7075 aluminum now include keys, gears, and other high-stress parts. It is often used as a replacement for 2024 aluminum because it’s stronger and provides similar performance in all other aspects.

Designed for use as production injection molds and blow molds, QC-10 is extremely strong with a hard surface and excellent thermal conductivity.

From cookware to chemical-processing equipment, 304 stainless steel is a good all-around choice for a wide range of applications.

Polished to either a brushed or mirror-like finish, this material is often used to fabricate decorative enclosures and industrial workstations.

Harder than our other 304 stainless steel, these thin sheets offer better wear resistance for use as a wrap, liner, or cover.

The textured surface hides fingerprints and dents. This material is widely used in decorative applications, such as partitions and handrails.

Widely used for fabricating fittings and fasteners, 303 stainless steel machines quickly without sticking to cutting tools.

Use 430 stainless steel in decorative and light structural applications, rather than outdoors or in extreme temperatures.

The addition of molybdenum gives 316 stainless steel excellent corrosion resistance. Use it in a variety of marine and chemical-processing applications.

One side of these sheets is polished to either a brushed or mirror-like finish.

Because these thin sheets are harder than our other 316 stainless steel, they offer better wear resistance. Use them as a wrap, liner, or cover.

Precision ground on the top and bottom to a tight tolerance.

Also called flat stock, these precision-ground bars are held to tight thickness and width tolerances.

440A stainless steel resists damage from impact and abrasion. It's often used for cutlery and valve components.

One of the hardest types of stainless steel after heat treating, 440C offers excellent wear and abrasion resistance. It's often used for bearings, valves, and knife blades.

The width and thickness are oversized for finishing to your exact requirements.

309/310 stainless steel has high levels of chromium and nickel to provide good corrosion resistance at elevated temperatures. It's often used in heat exchangers and furnaces.

With a higher chromium content than 15-5 PH stainless steel, this high-strength 17-4 PH offers better corrosion resistance. It is also known as 630 stainless steel.

Each piece is precision ground to offer tighter tolerances than standard 17-4 PH stainless steel.

As the most formable of all the PH-grade materials, 17-7 PH stainless steel is widely used in the aerospace industry for intricate parts. When hardened, this material strengthens to make it resist distortion.

These precision-ground sheets and bars are held to a tight thickness tolerance.

These sheets and bars are precision ground to a tight thickness tolerance.

The thickness on these bars is precision ground to a tight tolerance.

These W1 bars have lower amounts of alloy elements than other tool steels for excellent machinability.

These bars have an oversized thickness, length, and width for finishing to your exact requirements.

Hardened for increased abrasion and impact resistance.

Offering high electrical conductivity and formability, 110 copper is 99.9% pure. Also known as ETP copper, it's often used in electrical applications, such as for bus bars and wire connectors, as well as for flashing, gaskets, and rivets.

An ultra-thin layer of silver makes these bars slower to tarnish than unplated copper to provide low electrical resistance at contact points over time.

One side of these sheets has a brushed finish with grain lines running in one direction to mask fingerprints.

With 99.99% copper content, 101 copper has higher purity than 110 copper, resulting in superior electrical conductivity. It's commonly called OFE and OFHC copper. Use it in electrical applications, such as for coaxial cables and terminal lugs.

In addition to being conductive, these 175 beryllium copper bars are non-sparking and non-magnetic, so they’re used in mines and oil rigs, as well as for navigational tools.

With the highest lead content of all the brass alloys, 360 offers the best machinability. Often called free-machining and free-cutting brass, it stands up to high-speed drilling, milling, and tapping operations with minimal wear on your tools. It’s commonly used for gears, pinions, and lock components.

Often called architectural bronze, 385 brass is easy to machine and has excellent formability when heated. It is typically used for handrails, ornamental trim, and hardware, such as hinges and lock bodies.

A lead-free alternative to 485 brass, 464 brass offers good weldability, strength, and wear resistance. It’s widely used for marine hardware, pump and propeller shafts, and rivets.

Thickness and width are oversized to allow for finishing.

Frequently called manganese brass, 863 bronze can handle heavy loads and high speeds when properly lubricated. These bars are a higher-strength alternative to tight-tolerance 954 bearing bronze bars.

Powdered bronze is pressed and then impregnated with SAE 30 oil to make this material self-lubricating.

Even in temperatures up to 2000° F, Alloy X nickel sheets offer good strength and weldability, along with excellent oxidation resistance. They're often used for components in gas turbine engines and furnaces. This material is equivalent to Inconel HX and Hastelloy X.

200 nickel sheets and bars are over 98% pure, so they offer outstanding corrosion resistance along with good formability, weldability, and electrical conductivity. They're often used in food-processing equipment and chemical shipping drums.

Because Grade 2 titanium is 99% pure, it is more corrosion resistant than Grades 5 and 9 but not as strong. It has good formability and weldability. Common uses include chemical processing equipment, heat exchangers, and marine hardware.

These bars are also known as flat stock.