We will reply to your message within an hour.
Make clean cuts through duct tape and other sticky materials.
S-shaped handles keep your hand clear of material, so you can cut flush against flat surfaces.
These small scissors have narrow, sharp tips for fine cutting and trimming.
Prevent snags and injury with the rounded points on these small scissors.
Short blades make these scissors easy to maneuver in cramped areas for small, detailed cuts less than an inch long.
Trim flush against a flat surface with the curved blades on these small scissors.
Cut through the strong fibers of Kevlar.
For extra leverage to cut through Kevlar, metal, and plastics, these scissors have long handles and short blades.
After each cut, the jaws spring open to make continuous cutting easy.
Insulated handles protect against shock from accidental contact with live electrical circuits. These scissors are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.
Also known as electricians' shears, the back edge of the blade has a file to clean contacts.
Protect sensitive equipment from harmful static discharges while cutting and stripping wire.
Cut and strip wire in tight spaces with the compact tips on these scissors.
A double hinge provides high cutting force with low gripping pressure. These cutters are also known as aviation snips.
Keep your hand away from the material being cut.
Blades are high-speed steel so they stay sharp longer than steel blades, and they can be sharpened.
The handles are angled 90° from the blade so you can cut material from directly above tight spaces.
Snip tighter curves in smaller spaces than standard high-force cutters.
Make straight and curved cuts in sheet metal—these sets come with three tools for different cutting patterns. Also called aviation snips, they have a double hinge, so they cut with more force and require less effort to squeeze the handles than standard sheet metal cutters.
This cutter has two blades that cut a 1/8" wide strip—peel it back for smooth edges with little distortion.
Prevent waste from flying up as you work. A double blade makes two cuts to create a 7/64"-wide step that peels back, leaving little distortion and smooth edges.
Also known as tinners' snips, these cutters make straight cuts and curves.
Also known as bulldog snips, these have long handles and short blades for cutting through thick sheet metal with less effort than standard sheet metal cutters.
Handles are angled to keep your hand away from the material as you cut straight lines and curves.
Blades are tapered to give you more control when cutting straight lines, tight curves, and circles, and they're serrated to prevent slipping. These cutters are also known as duckbill snips.
Replace blades as they wear. These cutters are also known as tinners' snips.
The unique shape of these cutters gives you 40% more power per cut than standard sheet metal cutters. When blades get dull, loosen a few screws to replace them.
Loosen a few screws to swap dull blades with new ones. These cutters have offset handles to keep your hands clear of the metal being cut.
Made from aluminum bronze, the blade and handle on these cutters inhibit sparking and are FM approved. Use them for straight cuts.
Sized and shaped like pliers, these sheet metal cutters are small enough to fit in your tool belt.
Make round, square, and irregular-shaped holes with this punch-style hole cutter.
Cut up to 1" deep V-shaped notches in sheet metal.
A double blade creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.
Use to cut patterns in flat material with minimal material loss and less effort compared to manual cutters.
Punch small pieces out of material to create an almost burr-free cut with no material distortion.
Minimize material loss and edge distortion with these scissor-like cutters that cut metal up to 1/64" thick.
Convert your drill into a sheet metal cutter to make quick, low-effort cuts without a separate power tool.
These nibblers punch small pieces out of material to create an almost burr-free cut with no material distortion.
Also known as slotting shears, these cutters have a double blade that creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.
Also known as scissor-blade shears, the bottom blade remains stationary while the upper blade moves up and down to cut metal up to 1/64" thick with minimal material loss and edge distortion.
Turn your portable drill into a punch cutter for cutting curved and straight shapes in flat and corrugated sheet metal and plastic.
Make straight, clean cuts in thick sheet metal.
Make long, straight cuts around your facility—these cutters have a 12" blade and are light enough to move from bench top to bench top.
Move these lightweight cutters wherever you need to make clean, straight cuts through metal.
This large-capacity cutter has a 25" blade for long, straight cuts.
Combine the cutting base and a corner punch to make rounded corners in sheet metal.
Turn your workpiece while cutting to create curves and complex shapes.
Notch, cut, and pierce a variety of materials including metal, plastic, and vinyl.
Make straight cuts in sheets. These cutters are foot operated so your hands are free to position the material.
Leave clean cut edges in a variety of pliable materials.
Mount this cutter to the floor and use it to cut through steel angle iron up to 2"×2"×1/4".
Cut armored cable such as BX, HCF, and MC and flexible metal conduit.
Use these one-handed cutters on small-diameter aluminum and copper power and communication cable.
Minimize wire distortion when cutting 11/16" diameter and larger aluminum and copper power and communication cable.
Push the button to cut aluminum and copper power and communication cable.
Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.
Jaws ratchet to increase cutting pressure as you open and close the handles.
Also known as nippers, these cutters have wide, flat jaws that cut steel wire and bolts close to the surface.
Make accurate, flush cuts through small wire with these tweezer-style cutters.
Plastic-cushioned grips make these cutters easy to hold during repeated cuts.
The carbide-tipped steel jaws stay sharp longer than standard steel jaws. You can sharpen them as they wear. These cutters have a double hinge that provides high cutting force with low gripping pressure.
A double hinge provides high cutting force with low gripping pressure.
Cut hard steel wire, nails, and small rivets close to the surface with the wide, flat jaws on these cutters.
Shaped like tweezers, these cutters make accurate, flush cuts in small wire without damaging the surface underneath. The grips drain static away from the tips, protecting sensitive components from electrostatic discharge (ESD).
Snip wire close against circuit boards and other electronic components without building up electrostatic discharge (ESD).
These powerful cutters make diagonal cuts with a nipping action to cut extra-hard wire with ease.
Cut thin, hard wire with these small cutters.
Make one-handed cuts with these small cutters.
An angled cutting head keeps handles up and out of the way for trimming bolts, chain, and wire against flat surfaces. Smaller than standard bolt cutters, these cutters can be used one-handed in tight spaces.
Handle is angled 30° to keep work in sight and hands clear of the work surface. Blades are flat on one side for close-to-the-surface cuts.
Keep a variety of small cutters on hand for cuts in tight spaces.
Cut through hard metal bolts, chain, and padlocks with these cutters.
Leverage points on the jaws and handles let you cut through bolts, chains, and rods with 30% less effort than standard bolt cutters.
Cut medium steel chain and hard steel bolts, rods, screws, rivets, nails, bars, wire, and rebar.
Slice through bolts and chain with low effort.
The cutting head is angled 30° from the handles, so you can cut close to a surface or in a tight space without the handles getting in your way.
Make repeated cuts in hard materials with cutters that mount for stability and provides extra leverage.
Minimize material distortion while cutting steel and stainless steel wire rope.
Cutters have double hinge that provides high cutting force with low gripping pressure.
Keep your hands in a comfortable position so you can apply more force for cutting.
A small grip enables one-handed cutting.
Use the lever to make one-handed cuts with minimal material distortion. Cutter mounts to a workbench for extra stability and ease of use for repeated cuts.
With a quick hammer blow, these cutters make cuts without squeezing or flattening wire.
These manually operated cutters make a clean cut with just a few pumps of the handle.
An alternative to hacksaws and bandsaws, these cutters use leverage to cut rods cleanly in a single stroke.
Make clean cuts on threaded rod with the pull of a trigger.
Hydraulic-powered jaws cut bolts, wire rope, rods, and electrical cable with low effort and minimal material distortion.
Pull the lever on these cutters to make smooth cuts in steel and aluminum DIN rail without leaving a bur.
Keep one hand free while cutting and trimming strapping.
Two-handed strap cutters give you more leverage than one-handed strap cutters.
Slip strapping into the slot and rotate the handle to snap the strap.
Save space in your shop by cutting, bending, and curving sheet metal with a single machine. Also known as shear brake rolls.
Trim solid rivets to the length you need without changing their shape.