Woodruff keys work well near shaft shoulders and on tapered shafts. These keys have a rounded shape that makes them easy to remove when parts need to be taken apart frequently. Use them in light duty applications to connect gears and other components to shafts. Also known as half moon keys.

These keys have a tapered body that wedges in to the keyway for a more secure fit than standard machine keys. The gib head makes them easy to remove when parts need to be taken apart frequently, such as for maintenance or prototyping.

Cut this stock to length to create the machine key you need. Straight keys, with a square or rectangular cross section, are the most common type of key. Install in a keyway to transmit torque from shafts to gears and other components.

Slightly larger than the size listed, these oversized keys offer a tight fit in worn keyways.

A rounded bottom allows these keys to rock in their seat to relieve stress on the shaft caused by vibration or misalignment.

Sets include an assortment of keys. These simple tools turn fasteners from either end and reach into tight spots.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.

These keys have an extra-short leg to fit into tight spaces that other tools can’t.

All of the keys in these sets have an extra-short leg to fit into tight spots and a ball end to turn screws at an angle in hard-to-reach places. Their bright chrome-plated finish makes them easy to see, reducing the chance you’ll lose them.

These keys have an extra-short leg to fit into tight spaces that other tools can’t, and a ball on the long leg for angled entry to turn screws in hard-to-reach places. A bright chrome-plated finish makes them easy to see and less likely to be misplaced.

A bright finish makes these tools stand out, so they're less likely to be misplaced. They turn fasteners from either end and reach into tight spots.

Each size of these keys is a different color for easy identification. When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.

The ball end has a detent to grip inside the screw recess and allows angled entry to turn fasteners in hard-to-reach areas.

A flexible joint provides access to fasteners in hard-to-reach areas.

The zinc coating on these keys resists salt-spray exposure. They turn fasteners from either end and reach into tight spots.

The ball end allows angled entry to turn screws in hard-to-reach areas. Protect your stainless steel screws by using a stainless steel L-key. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Sets include an assortment of stainless steel keys, which protect stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Made of beryllium copper that is FM approved, these keys help meet OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. They turn fasteners from either end and reach into tight spots.

Sets include assorted keys with long shafts that reach into tight spots. The plastic-covered handles provide a good grip for your whole hand.

Sets include an assortment of short keys that fit in tight spaces where others can't.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. The textured grip provides comfort, slip resistance, and maximum torque.

These assorted keys have a textured grip that provides comfort, slip resistance, and maximum torque. They have a long shaft for reaching into tight spots to turn fasteners.

The economical choice, these sets include an assortment of keys with a simple loop handle. The long shaft reaches into tight spots and the T-handle provides a good grip for your whole hand when turning fasteners.

These sets include an assortment of keys with a ball end on the long shaft, which allows angled entry to turn screws in hard-to-reach areas. The short shaft provides additional torque.

These assorted keys have an extra-long shaft that provides access to fasteners in deep recesses. To change tips, use a hex key to loosen the set screw.

These assorted keys have a ball-end tip with a retaining ring that grips inside the recess to hold screws in place and allows angled entry to turn fasteners in hard-to-reach areas.

The long shaft provides more reach and the short shaft more torque. Protect your stainless steel screws by using a stainless steel key. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC and ASTM standards. They have a long shaft that reaches into tight spots to turn fasteners.

Each slot is marked with the size. Set these organizers on a bench top or wall mount.

The toughest bits available, these withstand the shock and twisting force of impact drivers.

A retaining ring grips inside the recess to hold screws in place. These bits have a ball end that allows angled entry to drive screws in hard-to-reach areas.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

An opening at the tip accommodates the pin in the recess of tamper-resistant hex screws. These are also known as pin-in-hex or pin-in-socket bits.

The toughest bits available, these withstand the shock and twisting force of impact drivers.

When you don't have exact alignment between the fastener and the bit, the ball end allows angled entry to turn screws in hard-to-reach areas. A retaining ring grips inside the recess to hold screws in place.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

Sets include an assortment of drivers with soft, contoured handles that provide comfort and the best possible grip for achieving maximum torque.

The assorted drivers in these sets have a ball end that allows angled entry to turn screws in hard-to-reach areas.

The assorted drivers in these sets have a holding mechanism at the tip that ensures the screw won’t slip off.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC, EN, or ASTM standards.

Insert a bit into the shaft and a magnet holds it in place.

The ball-end tip allows angled entry to turn screws in hard-to-reach areas. These tools are a scaled-down version of standard changeable-shaft screwdrivers, They're shorter, slimmer, and easy to take with you. Remove and replace the shaft to change the tip size.

Bits have a different tip at each end and snap into the shaft, which is also a nutdriver.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet ASTM and IEC standards.

Select any key without unfolding the others in the set. The assorted keys turn multiple fastener sizes.

Bright-colored handles make these tools stand out, so they’re less likely to be misplaced. Sets include an assortment of keys for turning multiple fastener sizes.

Also known as ESD-safe screwdrivers, the handle drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Press the rotating end cap on the handle with your palm to apply constant pressure while turning the body of the screwdriver with your fingertips.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas. Press the rotating end cap on the handle with your palm to apply constant pressure while turning the body of the screwdriver with your fingertips.

Sets include an assortment of drivers with a tip that can be replaced when it becomes worn. Press the rotating end cap on the handle with your palm to apply constant pressure to small fasteners while turning the body of the screwdriver with your fingertips.

Ensure carbide inserts are tightened to the correct torque. These tools are set to the recommended torque values for each screw size.

Create your own tool by attaching these shafts to a handle, or use with socket wrenches and power tools. They have a ball end that allows angled entry to make good contact with the recess when a standard-tip shaft can’t.

Extra-long bits allow access to hard-to-reach fasteners.

The short bit on these sockets fits in spaces where height clearance is limited.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

Use these sockets as an alternative to a screwdriver or L-key. They are made to withstand the high torque and force of impact tools.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet ASTM F1505 and IEC 60900.

The short bit on these sockets fits in spaces where height clearance is limited.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.