Sized for working on small equipment, these wrenches are 4 1/8" long with a slim head and handle.

The slim heads fit into tight spaces and around thin fasteners.

One head is angled 75° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

When turning fasteners in small spaces, these short wrenches fit where others can't.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the wrench.

Twist the grip to rapidly turn a socket before final tightening or to remove a fastener once loosened. The handle also swings like a traditional ratchet wrench.

The shaft on these wrenches extends and locks.

Rather than teeth, these wrenches use a series of rollers to engage the ratchet, enabling work in the tightest of spaces. Also known as silent ratchets, they don't make the traditional click sound when turned.

Set the desired torque and the wrench indicates when it's reached with an audible click and an impulse in the grip.

Made of beryllium copper, these wrenches satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

These wrenches have an accuracy of ±2.0%.

Trust the precision of your measurements—these wrenches are accurate to ±1%.

A main pointer on the dial shows torque as it’s being applied and a memory pointer indicates the maximum torque reached.

Trust the precision of your measurements—these wrenches are accurate to ±2%.

Turn sockets from above when there's not room to swing a standard wrench handle.

Pivot the head to access fasteners from an angle.

Also known as pipe plug sockets, these sockets have a square shape that provides the best possible grip on square fasteners and prevents rounding.

The short bit on these sockets fits in spaces where height clearance is limited.

Extra-long bits allow access to hard-to-reach fasteners.

Designed to fit inside strut channel, these sockets make it easier to mount the channel than using an extension or additional tools.

Achieve the best possible grip on hex fasteners and prevent rounding.

Tighten or loosen nuts and bolts without damaging the finish.

Pivot the head to access fasteners from an angle.

A magnet holds the fastener securely enough to drive self-tapping screws.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Suitable for occasional maintenance work, these sets are imported.

For high quality at a lower price, choose these U.S.A.-made sets.

The short bit on these sockets fits in spaces where height clearance is limited.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

Keep a convenient mix of hex, Torx, Phillips, and slotted bit sockets on hand.

Turn nuts on bolts and threaded rod, which pass through these sockets.

The hex shape grips hex fasteners and prevents rounding. These sockets are made to withstand the high torque and force of impact tools.

Use these sockets as an alternative to a screwdriver or L-key. They are made to withstand the high torque and force of impact tools.

Move the sliding clips to any position along the rail to hold a variety of sockets.

The rail is smooth plastic so the clips move more easily than on steel-rail organizers.

The slots in these low-profile organizers are a different color than the base so it's clear when tools are missing from your bench top or drawer.

Set on a benchtop or mount with screws.

Hold and carry wrenches on both sides of these caddies.

The slots in these low-profile organizers are a different color than the base so it's clear when tools are missing from your bench top or drawer.

The head is offset 45° to provide clearance for reaching over obstructions.

A ratchet mechanism allows you to turn fasteners in tight spaces without removing and repositioning the wrench.

Also known as slugging wrenches, strike the handle with a hammer to break stuck fasteners free.

A ratchet mechanism allows you to turn fasteners in tight spaces without removing and repositioning the wrench.

Open the jaws to fit around a fastener like an open-end wrench; close the jaws and the wrench acts like a ratcheting box wrench.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

Also known as E-style rings.

No groove required—press these rings onto the end of a shaft for a firm grip.

Also known as flat-style speed nuts, these have a large surface to distribute loads better than standard and flanged external push rings.

No groove required—these rings have teeth that firmly grip the bore.

Also known as flat-style speed nuts, these have large sides, so they're easy to push over threads by hand.