The toughest bits available, these withstand the shock and twisting force of impact drivers.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

A retaining ring at the tip grips inside the recess to ensure screws won't slip off the bit.

A magnet or retaining ring holds the nut in place.

A retaining ring grips inside the recess to hold screws in place. These bits have a ball end that allows angled entry to drive screws in hard-to-reach areas.

Assortments contain bits with multiple drive styles.

The knurled shank on these bits allows finger tightening. They can also be used with the included screwdriver.

Sets include assorted keys with long shafts that reach into tight spots. The plastic-covered handles provide a good grip for your whole hand.

Sets include an assortment of short keys that fit in tight spaces where others can't.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t.

These assorted keys have a textured grip that provides comfort, slip resistance, and maximum torque. They have a long shaft for reaching into tight spots to turn fasteners.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. The textured grip provides comfort, slip resistance, and maximum torque.

The economical choice, these sets include an assortment of keys with a simple loop handle. The long shaft reaches into tight spots and the T-handle provides a good grip for your whole hand when turning fasteners.

The long shaft has a ball end for angled entry to turn screws in hard-to-reach areas. The short shaft provides additional torque.

These assorted keys have an extra-long shaft that provides access to fasteners in deep recesses. To change tips, use a hex key to loosen the set screw.

These assorted keys have a ball-end tip with a retaining ring that grips inside the recess to hold screws in place and allows angled entry to turn fasteners in hard-to-reach areas.

Protect your stainless steel screws by using a stainless steel key. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

The assorted keys in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900 and ASTM F1505-01. They have a long shaft that reaches into tight spots to turn fasteners.

Extra-long bits allow access to hard-to-reach fasteners.

Extra-long bits allow access to hard-to-reach fasteners.

These sockets are also known as pin-in-hex or pin-in-socket bits.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

With a plastic insert, these sockets firmly grip hex nuts and bolts without rounding them or scratching highly polished finishes.

Turn many sizes of square, hex, and 8-point fasteners with one socket. Place over the fastener and 54 pins move to grip it securely.

Turn nuts on bolts and threaded rod, which pass through these sockets.

A rubber insert grips the plug to prevent damage.

Tighten or loosen nuts and bolts without damaging the finish.

A magnet holds the fastener securely enough to drive self-tapping screws.

Pivot the head to access fasteners from an angle.

Designed to remove and install dual wheels on trucks and trailers, these sockets have a hex recess for accessing lug nuts and a square recess to turn the threaded shafts found on inner wheels.

A magnet holds the fastener securely enough to drive self-tapping screws.

Extra-long bits allow access to hard-to-reach fasteners.

Extra-long bits allow access to hard-to-reach fasteners.

Keep a convenient mix of hex, Torx, Phillips, and slotted bit sockets on hand.

Suitable for occasional maintenance work, these sets are imported.

For high quality at a lower price, choose these U.S.A.-made sets.

Suitable for occasional maintenance work, these sets are imported.

Turn nuts on bolts and threaded rod, which pass through these sockets.

Remove and install dual wheels on trucks and trailers with the sockets in these sets.

The hex shape grips hex fasteners and prevents rounding. These sockets are made to withstand the high torque and force of impact tools.