We will reply to your message within an hour.
Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.
Extra length allows access to fasteners on long bolts.
Pivot the head to access fasteners from an angle.
With a plastic insert, these sockets firmly grip hex nuts and bolts without rounding them or scratching highly polished finishes.
For easy tightening and loosening, these sockets have pins that grip the slotted sides on bearing nuts.
Quickly position these sockets on square and external 8-point fasteners.
Turn many sizes of square, hex, and 8-point fasteners with one socket. Place over the fastener and 54 pins move to grip it securely.
The short bit on these sockets fits in spaces where height clearance is limited.
Extra-long bits allow access to hard-to-reach fasteners.
The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.
These sockets are also known as pin-in-hex or pin-in-socket bits.
The opening is designed to grip threaded rod for quick installation and removal without damaging the threads.
Designed to fit inside strut channel, these sockets make it easier to mount the channel than using an extension or additional tools.
A rubber insert grips the plug to prevent damage.
Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.
Achieve the best possible grip on hex fasteners and prevent rounding.
A magnet holds the fastener securely enough to drive self-tapping screws.
Tighten or loosen nuts and bolts without damaging the finish.
The 12-point shape quickly positions on hex fasteners.
Designed to remove and install dual wheels on trucks and trailers, these sockets have a hex recess for accessing lug nuts and a square recess to turn the threaded shafts found on inner wheels.
Use bit sockets as an alternative to a screwdriver or L-key.
Suitable for occasional maintenance work, these sets are imported.
Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.
Shaped and sized for compatibility with wheel bearing locknuts on trucks and trailers, the sockets in these sets make it easy to install and remove locknuts.
Keep a convenient mix of hex, Torx, Phillips, and slotted bit sockets on hand.
Turn nuts on bolts and threaded rod, which pass through these sockets.
The hex shape grips hex fasteners and prevents rounding. These sockets are made to withstand the high torque and force of impact tools.
Use these sockets as an alternative to a screwdriver or L-key. They are made to withstand the high torque and force of impact tools.
Remove and install dual wheels on trucks and trailers with the sockets in these sets.
The L shape provides clearance when reaching over obstructions.
Pivot the head for access to fasteners in tight spots.
Extend the shaft for additional length.
A rubber coating provides a comfortable grip.
Position the head anywhere along the handle.
Turn sockets in the most confined spaces.
Rather than teeth, these wrenches use a series of rollers to engage the ratchet, enabling work in the tightest of spaces. Also known as silent ratchets, they don't make the traditional click sound when turned.
The 20° offset head provides clearance when reaching over obstructions.
Made of aluminum-bronze, these wrenches satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.
Pivot the head to access fasteners in tight spots.
No need to pull the socket off the tool—push a button to release.
Insulated to protect against accidental contact with live electrical circuits, these wrenches are tested to 1,000 volts to meet IEC 60900.
When the ratchet head becomes worn or damaged, change it out for a new one.
Twist the grip to rapidly turn a socket before final tightening or to remove a fastener once loosened. The handle also swings like a traditional ratchet wrench.
A gasket seals in permanent lubrication and keeps out dirt, dust, and moisture.
Also known as a construction or spud handle, wrenches use the pointed end to align bolt holes.
The shaft on these wrenches extends and locks.
A ratchet mechanism allows you to turn fasteners without removing and repositioning the wrench.
The handle is covered in rubber for a comfortable grip.
Turn sockets from above when there's not room to swing a standard wrench handle.
The ratcheting mechanism turns sockets quickly.
Bend around obstructions to turn hard-to-reach fasteners.
Fasten quickly with these crank-style handles.
Trust the precision of your measurements—these wrenches are accurate to ±1%.
Measure with an accuracy of ±2%.
These wrenches have an accuracy of ±2.0%.
The most advanced torque wrenches we offer, these tools store and recall up to 1,500 torque and angle measurements.
A main pointer on the dial shows torque as it’s being applied and a memory pointer indicates the maximum torque reached.
Measure with an accuracy of ±7%.
Trust the precision of your measurements—these wrenches are accurate to ±2%.
When the set torque is reached, these wrenches signal with an audible click and an impulse in the grip.
Made of beryllium copper, these wrenches satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.
These wrenches slip to disengage and stop turning the fastener when the set torque is reached, preventing overtightening.
Set the desired torque and the wrench indicates when it's reached with an audible click and an impulse in the grip.
Unlike most torque wrenches, you don’t have to return the torque setting to the lowest value after use. These tools are also known as split-beam torque wrenches.
Also known as impact drivers, use these tools with impact sockets to break frozen bolts and screws free. Strike with a hammer to tighten and loosen fasteners.
Set torque and the wrench will prevent you from exceeding it. These are also known as nutrunners.
Built for durability, these high-performance tools handle the demands of high-volume production and tough maintenance applications.
Use these tools for general shop applications.
These tools are suitable for general shop, maintenance, and automotive work.
Built for durability, these wrenches handle the demands of high-volume production and tough maintenance applications.
Use these wrenches for medium-volume production, general maintenance, and construction applications.
Change a standard wrench handle into a ratcheting wrench.
Attach one of these adapters to a socket to turn it with an open-end or box wrench.
Fit these adapters between your wrench and socket to enable finger tightening.
Lock the adapter on your tool and the socket to the adapter to prevent accidental disengagement.
These adapters are insulated to protect against accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC 60900.
Turn sockets with a bit screwdriver.
A digital display shows how torque measurements change as you turn the wrench. Set the desired torque and angle—lights and an audible alarm indicate when target has been reached or exceeded.
Push the square drive through the adapter to change size.
Set a desired torque within the range.
Adapters are set to a specific torque and cannot be adjusted.
Convert from one square drive size to another.
Prevent overtightening that can damage fasteners. These adapters spring back slightly when the set torque is reached.
Pull the collar to quickly attach and remove sockets.
A magnet holds the socket, making changes quicker.
Use sockets with tools that accept hex shanks, such as impact drivers and power drills.
Change heads to use these tools as an open-end, box, square drive, or hex-key wrench.
Turn nuts on bolts and threaded rod, which can pass through the short end of the wrench. For additional leverage, slip a bar through the short end to create a T-handle.
Pivot the socket end to access hard-to-reach fasteners.
Turn lug bolts on car and truck wheels. These wrenches have a different socket size at each end.
Break stuck screws free using screwdriver bits. Strike the end of the handle with a hammer to turn the bit and tighten or loosen fasteners.
Choose a handle based on torque and change shafts to use a different size or drive style. Factory-set screwdrivers ensure you reach the same torque every time.
Attach a socket to the 1/4" square drive tip. These tools have a dial that shows how torque measurements change as you turn the driver. Use to fasten to a specific torque, determine fastener torque specifications, and identify the torque required to loosen tightened fasteners.
Attach a socket to the 1/4" square drive tip to turn hex nuts and hex head screws. When set torque is reached, these drivers signal with an audible click.