Extra length allows access to fasteners on long bolts.

With a plastic insert, these sockets firmly grip hex nuts and bolts without rounding them or scratching highly polished finishes.

Pivot the head to access fasteners from an angle.

Also known as pipe plug sockets, these sockets have a square shape that provides the best possible grip on square fasteners and prevents rounding.

Turn many sizes of square, hex, and 8-point fasteners with one socket. Place over the fastener and 54 pins move to grip it securely.

The short bit on these sockets fits in spaces where height clearance is limited.

Extra-long bits allow access to hard-to-reach fasteners.

These sockets are also known as pin-in-hex or pin-in-socket bits.

A rubber insert grips the plug to prevent damage.

Turn nuts on bolts and threaded rod, which pass through these sockets.

Achieve the best possible grip on hex fasteners and prevent rounding.

Pivot the head to access fasteners from an angle.

The 12-point shape quickly positions on hex fasteners.

A magnet holds the fastener securely enough to drive self-tapping screws.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Suitable for occasional maintenance work, these sets are imported.

Extra-long bits allow access to hard-to-reach fasteners.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

These sockets are also known as pin-in-hex or pin-in-socket bits.

Use these sockets as an alternative to a screwdriver or L-key. They are made to withstand the high torque and force of impact tools.

Pivot the head to access fasteners from an angle.

Set the desired torque and the wrench indicates when it's reached with an audible click and an impulse in the grip.

Made of beryllium copper, these wrenches satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Turn sockets from above when there's not room to swing a standard wrench handle.

When the set torque is reached, these wrenches signal with an audible click and an impulse in the grip.

These wrenches have an accuracy of ±2.0%.

The most advanced torque wrenches we offer, these tools store and recall up to 1,500 torque and angle measurements.

Measure with an accuracy of ±7%.

The slots in these low-profile organizers are a different color than the base so it's clear when tools are missing from your bench top or drawer.

Turn lug bolts on car and truck wheels. These wrenches have a different socket size at each end.

Turn nuts on bolts and threaded rod, which can pass through the short end of the wrench. For additional leverage, slip a bar through the short end to create a T-handle.

Turn hex nuts and cap screws.

Eliminate the need for multiple bulky tools with these bit adapters. At less than 3 inches long, these compact adapters convert ¼” bit screwdriver handles and ¼” bits into torque screwdrivers so you can fasten to a specific torque.

Sets include an assortment of nutdrivers.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet ASTM and IEC standards.

Apply constant pressure to small hex nuts and cap screws. Press the rotating end cap on the handle with your palm while turning the body of the driver with your fingertips.

Also known as ESD-safe nutdrivers, the handle drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the driver with your fingertips.

The standard for high-strength fastening.

Use these general purpose 18-8 stainless steel screws for a variety of fastening applications. They have good chemical resistance.

More corrosion resistant than 18-8 stainless steel screws, these 316 stainless steel screws have excellent resistance to chemicals and salt water.

These screws are hardened to be 40% stronger than standard 316 stainless steel screws, yet they still have excellent corrosion resistance. Use them in chemical and marine applications.

Brass screws are electrically conductive, nonmagnetic, and have good corrosion resistance.

Our most corrosion-resistant metal screws, titanium screws withstand salt water, acids, and chemicals. They have a high strength-to-weight ratio and are about 40% lighter than steel screws.

Nearly as strong as steel, these stainless steel screws won’t rust in outdoor, washdown, and other corrosive environments. With half the height of a standard socket head, these low-profile screws fit in tight spaces.

Made of alloy steel, these low-profile screws are nearly twice as strong as their stainless steel counterparts. With half the height of a standard socket head, these low-profile screws fit in tight spaces.

More corrosion resistant than 18-8 stainless steel screws, these 316 stainless steel screws have excellent resistance to chemicals and salt water. Their ultra-low-profile lets them fit in the tightest spaces.

With a tensile strength of 170,000 psi, these alloy steel screws are among the strongest we carry. They are stronger than Grade 8 steel screws and are nearly two and a half times stronger than stainless steel thread-locking screws. They have a thread locker to prevent loosening from vibration.

Serrations under the head grip the material's surface for mild vibration resistance. The flange distributes pressure across the material's surface, eliminating the need for a washer.

Drilled through the head and shaft, these screws vent fluid and gases trapped below the screw, making them good for vacuum applications.

The nylon patch bonded to the threads of these socket head screws adds friction to keep vibration from loosening them, while their O-ring prevents leaks and seals out contaminants.

Closely spaced threads on these screws fit in holes with a fine pitch. They're not compatible with standard metric threads.

Made from brass, these metric button head screws are corrosion resistant in wet environments, nonmagnetic, and electrically conductive.

The Torx or Torx-Plus drive on these metric screws have more points of contact than other drives, allowing you to tighten them without damaging the recess.

Made from A286 stainless steel, these metric screws provide the strength of alloy steel and the corrosion and chemical resistance of 18-8 stainless steel. They have a Torx drive that has more points of contact than other drives, allowing you to tighten the screw without damaging the recess.

These metric screws have a Torx drive for more points of contact than other drives, allowing you to tighten the screw without damaging the recess.

These metric alloy steel screws are nearly twice as strong as stainless steel button head screws. They have a flange that distributes pressure across a wide surface, eliminating the need for a separate washer.

These metric 316 stainless steel screws resist corrosion from chemicals and salt water better than 18-8 stainless steel screws. They have a flange that distributes pressure across a wide surface, eliminating the need for a separate washer. Screws may be mildly magnetic.

Made from aluminum, these metric screws are lightweight and resist corrosion in wet environments. The flange is wider and thicker than our other flanged screws, so they distribute pressure the best.

Made from 18-8 stainless steel, these metric button head screws have good chemical resistance and may be mildly magnetic. The tamper-resistant hex drive (also known as a pin-in hex drive) makes them difficult to remove without special tools.

To prevent unwanted removal, these metric screws have a tamper-resistant Torx drive—also known as a pin-in Torx drive—that makes them difficult to unscrew without special tools. An O-ring under the head blocks leaks and seals out dust and dirt.

More corrosion resistant than 18-8 stainless steel screws, these metric screws have excellent resistance to chemicals and salt water. They may be mildly magnetic.

These metric brass screws are electrically conductive, nonmagnetic, and have good corrosion resistance.

These metric 18-8 stainless steel screws have good chemical resistance and may be mildly magnetic.

With a tamper-resistant Torx drive (also known as a pin-in Torx drive), these metric screws are difficult to remove without special tools.

With a tamper-resistant hex drive (also known as a pin-in hex drive), these metric screws are difficult to remove without special tools.

These metric set screws have good chemical resistance.

These alloy steel set screws have a thin edge that digs into hard surfaces for a secure hold. They're available in metric sizes.

These metric 18-8 stainless steel set screws are chemical resistant. They have serrations on the cup edge that grip the material surface to resist loosening.

Made from alloy steel, these metric set screws have a thin edge that digs into hard surfaces for a secure hold. They have a nylon locking patch that grips threads to resist loosening.

These metric set screws have a tip that makes good contact on flat surfaces and allows you to make frequent adjustments with minimal surface damage.

These metric 316 stainless steel set screws have excellent chemical resistance and can be used in saltwater environments. The tip makes good contact on flat surfaces and allows you to make frequent adjustments with minimal surface damage.

Made of chemical-resistant 18-8 stainless steel, these metric screws have an extra-soft nylon tip that reduces the noise, vibration, and damage that can occur from metal-on-metal contact. Use them on soft surfaces such as aluminum.

Available in metric sizes, these screws have a tip that is harder than nylon and silver to provide a secure hold on hard surfaces. The body is 18-8 stainless steel for good chemical resistance.

Fine threads give you precise control.

Made from alloy steel, these metric set screws have a pointed tip that wedges into the contact surface for a secure hold on soft materials such as brass.

These metric set screws have a protruding tip that locks within a mating hole or slot to keep parts aligned. They're also known as dog-point set screws.

Comparable to Class 12.9 steel.

The metric-sized threads on these screws are the same diameter as the shoulder. Comparable in strength to Class 12.9 steel.

With inch-sized threads the same diameter as the shoulder, these screws can handle heavy loads. They’re 18-8 stainless steel for good chemical resistance.